Journal of Materials Research and Technology-JMR&T

Article	Citations
Microstructure evolution during oxidation of quinary Ti3(AlSiSn)C2 at high temperatures and induced probable performance	607
Accelerated testing of soft soldered, small-diameter, thin-walled CuNi pipes subjected to cyclic internal pressure loading	497
Models for plastic flow: People, places, concepts and techniques	459
Intergranular creep resistance affected by grain boundary carbides to suppress lamellae γʹ precipitation in a specially designed inconel 740H variant	375
Study on microstructural evolution of SiCox/Al-4.2Cu-4.0Mg composites during aging process	255
Effect of strain rate on the deformation mechanism of laser powder bed fusion (LPBF) Ti – 10V–2Fe–3Al alloy before and after solution treatment	247
Corrosion behaviors of pre-oxidized Al-containing Fe alloys in molten NaCl–KCl salts	219
Effect of heating and bending on localized critical current in 2G HTS tapes with non-contact trapped field measurements	218
Effect of Ni and Nb concentration on microstructural evolution in a 20Cr ferritic alloy strengthened by Ni16Nb6Si7-G phase	207
Suppression of Cr nanoclusters and enrichments in Fe–Cr based alloys with cryogenic processing for future energy sector	201
Influence of pre-strain on inelastic recovery and shape memory property of metastable Ti–10V–2Fe–3Al alloy	200
High fracture toughness: Nacre-mimetic HA-CaCO3/SA layered composites without sintering	195
Structural evolution and precipitation behavior of titanium diboride-reinforced 7075Al composites during multi-pass rolling	186
Interaction of displacement cascades with {10 1	184
A facile synthesis by spark plasma sintering of mobile lithium ions into oxynitride glass-ceramic matrix: Insight and perspective	181
Corrigendum to “Melting behavior of in-flight particles in ultra-high speed laser cladding” [J Mater Res Technol 24 (2023) 7047–7057]	181
Development of TiO2-doped MgO refractories with enhanced corrosion resistance for preparing high-purity nickel-based superalloys	177
Sequential solution annealing of a CrMnCN austenitic stainless steel	173
Effect of bimodal powder on densification and mechanical properties of 316L stainless steel fabricated by binder jet 3D printing	166
The evolution of precipitates and mechanical properties in rapidly solidified 2195 Al–Cu–Li alloy during thermal exposure	165
Mechanical performance improvement for various 9Cr ODS alloys at room temperature and 650 °C by tailoring hot rolling and subsequent heat treatments	164
Achieving superior ductility and toughening in as-cast 2055 Al–Li alloy through single-pass rolling with a small reduction ratio for homogenization	163
Corrigendum to ‘Study on laser cladding and properties of AZ63-Er alloy for automobile engine’ [Source J Mater Res Technol-JMR&T 9 (3), (May–June 2020) Pages 5154–5160]	158
Corrigendum to ‘The regolith-hosted clay REEs leaching effects by mechanical grinding and at low temperature: An analogy on treatment method’ [J Mater Res Technol 37 (2025) 2338–2351]	157
Revisiting the model for austenite grain size of M50 steel coupled with the carbide dissolution behavior	156

Microstructure and heat resistance of Al–Cu–Mg–Ag alloy fabricated by wire-arc directed energy deposition	155
Influence of Mn on nanobainite formation kinetics and austenite retention in Al-added medium-Mn steels subjected to hybrid isothermal annealing	153
Tripling thermoplastic adhesive tape shear fatigue lifetime by decorating the adhesive–carrier interface with tailored sacrificial defects	148
Balance interlaminar improvement and in-plane adverse impact of hexagonal semi-embedded fine Z-pin reinforced polymer composite	144
Precipitation kinetics of precipitates with different orientations and segregation in an ultrafine grained Al–Cu–Mg alloy	144
Synthesis and purification of nano-sized titanium carbide particles through vacuum carbothermal reduction for enhanced mechanical, microstructural morphology, and tribological properties in friction s	141
Effect of rare earth yttrium and the deformation process on the thermal deformation behavior and microstructure of pure titanium for cathode rolls	135
Study on the microstructure and properties of TiB2-CoCrFeNiW0.2 metal ceramic composites prepared by pressureless sintering	133
Tensile mechanical behavior and failure mechanism of 2.5D woven fabric reinforced aluminum matrix composites involving residual stress	133
Recrystallization processing of additively-manufactured oxide dispersion strengthened Ni alloys	132
Cryogenic thermal cycling induced simultaneous improvement of strength and ductility in a Zr-based bulk metallic glass composite	126
High efficient photoreduction of U(VI) by a new synergistic photocatalyst of Fe3O4 nanoparticle on GO/g-C3N4 composites	126
Hybrid modeling prediction of residual stresses in turned Ti6Al4V considering frictional contact	126
Adaptability analysis of H2-rich gas injection and sintered ore performance with different raw material ratios	124
Influence of shielding gas flow on pore evolution in AlSi10Mg/In718 alloy by laser powder bed fusion	122
Experimental investigation of material extrusion additive manufacturing of copper with high powder loading rate	122
Effects of single/double stage cold rolling and aging treatment on the α-Fe phase, microstructure, and properties of Cu–12Fe-0.42Si-0.008B alloy	118
Effect of interaction between bubbles and interfaces on irradiation hardening of vanadium alloy and ODS steel	114
A damage model that can be coupled with constitutive behavior prior to necking for SGAFC 780 steel	111
Mechanical and optical properties of multilayer yttria-stabilized zirconia for dental prostheses	110
Effects of cooling rate on isothermal spheroidizing annealing of hot-rolled GCr15 bearing steel	110
Microstructure and mechanical properties analyses of Ti(C, N)–Fe/low-carbon steel composite material	108
Enhanced high-temperature strength and ductility of wire arc additive manufactured Al–Ce–Mg alloys with fine α-Al/Al11Ce3 eutectics	105
Application of shot peening to improve fatigue properties via enhancement of precipitation response in high-strength Al–Cu–Li alloys	105
Influence of chemical and bio-surfactants on physiochemical properties in mesoporous silica nanoparticles synthesis	104
Influence of combining Al2O3, La2O3, Gd2O3, and Dy2O3 with barium borosilicate glass-ceramics: a case study of gamma radiation interaction parameters	104
Study on the magnetic viscosity of multi-step magnetized heterogeneous alloys	102
Microstructure evolution, diffusion behavior, and mechanical properties of a Cu/AlCoCrFeNi2.1 composite under pulsed magnetic field	102
3Y-TZP electrostatic painting to increase bond strength to dentin and dental prostheses	100
Static softening behavior of 316L stainless steel under flexible rolling process	99
Predicting the three-dimensional grain structure of superalloys during vacuum arc remelting process	99
Effect of molybdate on crevice corrosion initiation of hydrogen-charged duplex stainless steel	98
Bioinspired fibrous microstructure breaks strength and toughness trade-off in plain carbon steel	98
Biomimetic 4D printing of dome-shaped dynamic mechanical metamaterials	97
Corrigendum to “Study on the surface properties of the regenerated polyurethane foam micropowder via cryogenic pulverization and its application” [J Mater Res Technol 23 (2023) 808–818]	96
Electron microscopic investigation of precipitation hardening in Al-Si based alloys	94
Microstructure and microhardness of electron beam melted Ti–6Al–4V components with differential thickness in initial deposition layers	93
Isothermal foaming-nucleation-crystallization of glass ceramic foams with hierarchical pore structure: A sustainable approach for disposal of secondary aluminum ash	92
Enhanced mechanical properties of Zr65Cu15Ni10Al10 bulk metallic glass by simultaneously introducing surface grooves and multiple shear bands	92
Preferential growth of intermetallics under temperature gradient at Cu–Sn interface during transient liquid phase bonding: insights from phase field simulation	92
Effect of tensile stress annealing on residual stress and strength of C19400 alloy	92
Microstructure development and mechanical properties of a C-Mn-Si-Al-Cr cold rolled steel subjected to quenching and partitioning treatment	91
Sustainable geopolymerization approach to stabilize sabkha soil	91
Removal mechanism of Hydroides fouling on high-strength steel in the marine environment during nanosecond pulsed laser cleaning	91
Microstructure-based 3D finite element modeling of deformation and damage of (ZrB2+B4C)/6016Al hierarchical composites	91
Microstructures and thermal conductivity anisotropy of hot-rolled Cu/Kovar composites sheet	90
Influence of laser absorptivity of CuCr0.8 substrate surface state on the characteristics of laser directed energy deposition inconel 718 single track	89
Microstructures and mechanical properties of additively manufactured Fe–21Mn-0.6C TWIP steel using laser powder bed fusion	88
Toward single crystal nickel fabrication using WAAM – A first report	87
Prediction of titanium burn-off and untimate titanium content in electroslag process	87

Stability criteria of Aluminum lattice from first-principles	87
Mechanical characterizations of η′-Cu6(Sn, In)5 intermetallic compound solder joint: Getting prepared for future nanobumps	87
Study of the corrosion behavior of cast Ti2AlNb alloy in HF–HNO3 solution	87
Exploring the impact of pre-existing helium bubbles on nanoindentation in tungsten through molecular dynamics simulation	87
Investigation of mechanical integrity and high-cycle fatigue behavior of 3D-printed PLA/PCL blend after exposure to a physiological environment	86
Strain-induced fabrication of anisotropic nanopores by in-situ E-beam irradiation	86
Improvement of surface properties of fiber-reinforced polymer composites by metallization strategies: Technologies, challenges and prospects	85
Elemental synergistic effect in CoxCrCuFeMnNi high-entropy alloys and its influence on phase and magnetic properties	85
A comparative study on microstructure and mechanical properties of wire-arc directed energy deposited Al–Zn–Mg–Cu alloy based on the cold metal transfer technology	85
Thermal–microstructural analysis of the mechanism of liquation cracks in wire-arc additive manufacturing of Al–Zn–Mg–Cu alloy	84
Microstructural evolution and uniformity regulation in twin-roll casting Al–Mg–Si alloy plates via recrystallization annealing	84
Oxidation behaviors of a Ni–Cr–W based superalloy with different microstructures	83
Fabrication and characterizations of glass fiber-reinforced functional leaf spring composites with or without microcapsule-based dicyclopentadiene as self-healing agent for automobile industrial appli	83
Improved CMAS corrosion resistance of rare earth niobates by high-entropy and composite design	83
In-vitro cytotoxicity of zinc oxide, graphene oxide, and calcium carbonate nano particulates reinforced high-density polyethylene composite	82
The effects of room temperature soaking and deep cryogenic treatment on the stress relief phenomenon of Ti–Mo maraging stainless steel: experimental evidence and critical patents investigation	82
High-temperature radiation resistance of NiCoFe medium-entropy alloy enabled by stable nanostructures and defect evolution mechanisms	82
Numerical and experimental study of underwater friction stir welding of 1Cr11Ni2W2MoV heat-resistant stainless steel	82
Material removal rate model of single crystal diamond near atomic scale chemical mechanical polishing based on SOA	81
Eco-friendly, bright luminescent carbon dots and their potential applications for detecting hypochlorous acid in water and live cell imaging	81
Effects of powder morphology on stereolithography additive manufactured Al2O3 ceramic	80
Influence of thermal exposure on microstructural stability and tensile properties of a new Ni-base superalloy	80
A study on mechanical properties of CuNi2SiCr layered on nickel–aluminum bronze via directed energy deposition	80
Stress corrosion inhibition mechanism of hot rolled medium thickness Al–Zn–Mg–Cu plate by cryogenic-aging treatment	80
Biocementation by Sporosarcina pasteurii ATCC6453 under simulated conditions in sand columns	79
The role of initial grain size on bimodal-grained microstructure and mechanical properties of an extruded Mg-Gd-Y-Nd-Zr alloy	79
Electrodeposition of lead and lead-tin alloy on copper using an eco-friendly methanesulfonate plating bath	79
A novel high-strength Al–Li alloy printed by laser powder bed fusion: Microstructural evolution and strengthenin mechanism	79
Influence of basalt fiber on pore structure, mechanical performance and damage evolution of cemented tailings backfill	78
Synergistic effect of Al and Ti micro-alloying in CoCrNi-based medium entropy alloy	78
Investigation of corrosion behavior, tensile and cyclic fracture mechanism of EH36 steel welded joints	77
Effect of supersonic fine particle bombardment on microstructure evolution and tribological properties of GCr15SiMn bearing steel	77
Experimental investigation on wear resistance and corrosion behavior of nickel-aluminum bronze alloy fabricated by wire-arc additive manufacturing	77
Phase transformation and thermal stability of the laser powder bed fused high-strength and heat-resistant Al–Ce–Mg alloy	77
Development of the bioinspired multiscale structures for the enhancing impact resistance of the lightweight armor	76
Influence of Ni, Al, W doping on microstructure, corrosion and wear resistance of HVOF spraying Fe-based amorphous alloy coatings	76
Research on the joining of aluminum alloy and high-strength steel by dieless clinched-adhesive processes	76
First-principles study of metallic impurities induced 355 nm UV laser absorption in fused silica	75
Work hardening in metastable high entropy alloys: a modified five-parameter model	75
Biofunctional coating of stainless steel surfaces with carvacrol- and eugenol-derived film using atmospheric dielectric barrier discharge plasma: aiming for suppression of biofilm formation and corros	75
Predicting mechanical properties of bainitic rail steels based on microstructure digitalization and machine learning	75
Facile fabrication of transparent slippery glass coated with nanoscale silicone brushes having self-healing and liquid-like behavior	74
Local shear fracture properties in heat-affected zone of resistance spot-welded advanced high-strength steel	73
Deformation mechanism and resultant microstructural characteristics in extruded dilute Mg-0.1Bi-0.1Sn alloy with bimodal-sized grain structure under compression	73
Workability optimization and microstructure regulation for a multi-angular extrusion process of AZ80 magnesium alloy	73
Hexamethyldisiloxane coating by plasma to create a superhydrophobic surface for fabric masks	73
The effect of temperature and strain rate on the grain boundary sliding in a CM247 LC Ni-based superalloy processed with laser based powder bed fusion	72
Solidification structure and central segregation of 6Cr13Mo stainless steel under simulated continuous casting conditions	72
Altering tensile and crack initiation behavior in a metastable β titanium alloy via designing grain size and precipitates	72
A eutectic high-entropy alloy coating of novel hard-surface and soft-core structure with improved tribological properties	71
High temperature effects on fatigue performance and crack initiation mechanisms of 316LN stainless steel for nuclear power pipelines	71
The interrupted hot compression of an as-forged titanium matrix composite: flow softening behavior and deformation mechanism	70
Interplay of austenite and ferrite deformation mechanisms to enhance the strength and ductility of a duplex low-density steel	70
Sliding wear behaviors of the AlNiTi amorphous coatings: effect of temperatures	70
Effect of combined lean additions of isomorphous and eutectoid beta stabilisers on the properties of titanium	70
Behavior of stiffened concrete-filled steel tube columns infilled with nanomaterial-based concrete subjected to axial compression	70
Effect of gamma irradiation on microstructural evolution and mechanical properties of Sn3Ag0.5Cu solder joints	70
A criterion for fatigue failure mode evaluation of U-rib to deck joints	70
Ballistic response and failure mechanisms of gradient structured Mg alloy	69
Microstructure, mechanical properties and high temperature tribological behavior of NiAl-based composites	69
Research on asynchronous quenching behavior of boron steel tubular parts with variable cross-sections in hot gas forming-quenching integrated process	69
A novel route to improve the fatigue properties of aviation M50 steel via tailoring the bainite content and cold deformation	69
Graphene oxide and silver effects on the arc erosion properties of Al2O3–Cu/30Cr composite	69
Low cycle fatigue properties assessment and damage influence on DP 500/800 steel sheet	69
Composite nanofillers with a locust-like cushioned half-moon structure to improve the impact resistance of polyurethane	68
Heterogeneous nucleation and growth of interlaced CuO nanosheets on porous nickel foams as binder-free electrode material	68
Enhancement of mechanical properties and corrosion resistance in laser lap welding joint of zirconium R60702 by forced water-cooling	68
In-situ observation of twinning and grain rotation assisted deformation in wire-arc direct energy deposited (WDED) single phase titanium	68
Improved creep properties of a Ni-based single crystal superalloy by optimized solid solution treatments	68
Ductilization and grain refinement of AA7075-T651 alloy via stationary shoulder friction stir processing	67
A high-strength binary Mg-1.2Ce alloy with ultra-fine grains achieved by conventional one-step extrusion during 300–400 °C	67
Investigation of copper and zinc alloy surface exposed to corrosion environment by digital image processing	67
Effect of heat treatments on the microstructure and mechanical properties of a Ti–5Al–5Mo–5V–1Fe–1Cr alloy	67
Durability for coating mortars: Review of methodologies	67
In-situ SEM investigation of low-cycle fatigue behavior and microstructure evolution of CoCrNi medium entropy alloy	67
Anisotropic deformation mechanisms in textured nanotwined Cu under shock loading	66
Interface microstructure and phase constitution of AA1060/TA2/SS30408 trimetallic composites fabricated by explosive welding	66
Effect of pearlitic and bainitic initial microstructure on cementite spheroidization in rail steels	66
Effect of open die forging and cooling rate on the precipitation of secondary phases and corrosion properties of a cast UNS S32760 super duplex stainless steel	66
Effect of heat treatment on microstructure and hydrogen embrittlement of additively manufactured and cast 18Ni300 maraging steel	66

Microstructure, mechanical properties and high-speed dry-cutting performance of AlCrSiCN composite coatings	66
Enhancing the mechanical properties of 6061 aluminum alloy through the synergistic effects of twins, stacking faults, nanograins and lattice distortions	66
A comparison of granule-based material extrusion and fused filament fabrication in the performances of TPS/PBS blend	66
Effect of designed pore size on properties of additively manufactured TC4 with micro-nano biomedical surface	66
Evolution mechanism of grain orientation and texture distribution of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si alloy under electroshocking treatment	65
Low temperature plasma carburizing of additive manufactured 316 L steel: the effect of treatment time on tribological behavior	65
Effect of cold metal transfer mode on the microstructure and machinability of Ti–6Al–4V alloy fabricated by wire and arc additive manufacturing in ultra-precision machining	65
Effects of cooling manner on Laves phase precipitation and mechanical properties of Al modified super ferritic stainless steels	65
The mechanical coupling effect of laser shock and shot peening in Ti–6Al–4V dovetail joint: Residual stress, microstructure and fretting fatigue behavior	65
Synthesis and characterization of flyash reinforced polymer composites developed by Fused Filament Fabrication	65
Influence mechanism of solution temperature on microstructure evolution and tensile properties of Ti microalloyed high strength steel CGLC700	65
Ultrasonic welding of thermoplastic composites with woven mesh energy directors: Enhanced strength and hygrothermal resistance	65
Enhancing strength-ductility synergy of thermally oxidized dual-phase HEA particles reinforced aluminum matrix composites via heterogeneous interface	65
(La0.2Dy0.2Nd0.2Sm0.2Eu0.2)2GdTaO7: a promising candidate oxides for high-temperature coating applications	64
Influence of different rolling processes on microstructure, texture and anisotropy of the Al–Cu–Li alloy	64
Towards the preparation of organic ferroelectric composites: fabrication of a gamma-glycine-bacterial cellulose composite via cold sintering process	64
Water loss and defects dependent strength and ductility of articular cartilage	64
Rapid design of high-end copper alloy processes combining orthogonal experiments, machine learning, and Pareto analysis	64
Dependence of microstructure evolution of novel CoreFlow™ aluminium alloy wire on wire diameter	64
Enhancing surface quality in laser powder bed fusion using core-shell structured powder with micrometer-sized metal core and TiO2 nanoparticle shell	64
The effect of preforming and infusing bindered and unbindered carbon non-crimp-fabrics on the final quality of composites parts	64
Systematic study of (TiZr)xNby(TaMo)z medium entropy alloys for biomedical implants	64
Microstructure evolution and property strengthening of CuCr50 prepared by thermite reduction-electromagnetic casting during the heat treatment process	64
The feasibility of resistance seam welding as an additive manufacturing technology for Al 1060	63
Enhancement of electrical conductivity and corrosion resistance by gold-nickel coating of additively manufactured AlSi10Mg alloy	63
Achieving excellent oxidation resistance in a Mg alloy by grain boundary adhesion and in-situ phase transformation	63
Effect of Cu content on microstructure and high-temperature oxidation behaviors of AlCu CoCrFeNi2.1 high-entropy alloys manufactured by laser directed energy deposition	63
Regulate the microstructure, tensile properties and fatigue crack growth behavior of an Al–Zn–Mg–Cu alloys fabricated by laser powder bed fusion via post-heat treatment	62
Enhanced interfacial strength and ductility of stainless steel/carbon steel laminated composite by heterogenous lamella structure	62
Laser powder bed fusion of Ti6Al4V using low-cost high efficiency 450 nm diode point melting	62
Aging behaviors of the Al–Cu alloy via ultrasound-promoted thermal treatments	62
Determination of tensile strength and fracture toughness of nuclear graphite and prediction of its structural failures	62
Complex multiphase predicting of additive manufactured high entropy alloys based on data augmentation deep learning	62
Behavior of eccentrically loaded hybrid fiber-reinforced high strength concrete columns exposed to elevated temperature	61
Preparation of graphene film reinforced CoCrFeNiMn high-entropy alloy matrix composites with strength-plasticity synergy via flake powder metallurgy method	61
Strain-induced heterogeneous bimodal microstructure behavior of Mg-Gd-Y-Zn-Zr alloy containing LPSO phase during hot compression	61
Unraveling L12 Al3X (X=Ti, Zr, Hf) nano-precipitate evolution in aluminum alloys via multi-scale diffusion simulation	61
Preparation and sintering behavior of GdYb-YSZ nanostructured thermal barrier coating	61
Experimental study on the effects of triangular groove inclination angles on the mechanical behavior of sand–concrete interfaces	61
Microstructure, texture evolution and mechanical properties of a large-scale multidirectionally forged Mg-Gd-Y-Zn-Zr-Ag alloy	61
Study on the role of cryogenic treatment on corrosion and wear behaviors of high manganese austenitic steel	61
Hybrid Cu-to-Cu bonding with nano-twinned Cu and non-conductive paste	61
Quantitative analysis of 3D pore characteristics effect on the ductility of HPDC Al–10Si-0.3 Mg alloy through X-ray tomography	60
Effect of powder size segregation on the mechanical properties of hot isostatic pressing Inconel 718 alloys	60
ZnO/CuO nanocomposite-based carboxymethyl cellulose/polyethylene oxide polymer electrolytes for energy storage applications	60
Effects of multi-directional forging on the microstructure and mechanical properties of TiB2 particulate reinforced 6061Al composite	60
Assessment of thermal conductivity of polyethylene glycol-carbon dot nanofluid through a combined experimental-data mining investigation	60
Unveiling the effect of N interstitial on the mechanical properties of a CrFeCoNi medium entropy alloy	60
Compositional interpretation of high elasticity Cu–Ni–Sn alloys using cluster-plus-glue-atom model	60
Characterization of dynamic recrystallization and development of a processing map during hot deformation of FeCoCrNi high-entropy alloy	60
Tailoring β-Ti based shape memory alloy with the exceptional mechanical and functional properties towards biomedical bone implants application	60
Green penetration dyeing of wool yarn with natural dye mixtures in D5 medium	60
Studies on the Correlation between Irradiation Hardening and Thermal Conductivity of RPV Steel Irradiated with Protons	59
NdB6 ceramic nanoparticles: First principles calculations, mechanochemical synthesis and strain engineering	59
Microstructural and constitutive relationship in process modeling of hot working: The case of a 60Mg-30Pb-9.2Al-0.8B magnesium alloy	59
Designing impact-resistant bio-inspired low-porosity structures using neural networks	59
Microstructure and mechanical properties of extruded Mg–Zn–Mn–Ca alloys	59
Wear mechanism and evolution of tribofilm of ceramic on steel pairs under ester oil lubrication in wide temperature range	59
Achieving strength-ductility synergy of laser powder bed fusion Ti–6.5Al–2Zr–1Mo–1V alloy by regulating laser power	59
First principles calculations to investigate electronic, magnetic anisotropy energy and optical properties of MnCrP half-Heusler alloy	58
Behavior and evaluation of stress corrosion cracking of typical anchor bolt steel in simulated crevice environment	58
Structural evolution of PVP@Ag nanowires induced by focused electron beam irradiation: The passivation effect of PVP	58
Zinc oxide tetrapod sponges for environmental pollutant monitoring and degradation	58
Effectiveness of a CuZnNi alloy in preventing microbial growth and biofilm architecture	58
Effects of Si on the stress rupture life and microstructure of a novel austenitic stainless steel	58
Diffusion bonding of nickel-based powder metallurgy superalloy FGH98 with pure nickel interlayer	58
High strength and high electrical conductivity Cu composites reinforced by SiO2 aerogel particles	58
Quantized synaptic characteristics in HfO2-nanocrystal based resistive switching memory	57
Material hardening model effects on the calculated welding residual stresses in ultra-high strength steel S960	57
Effect of Cr on the microstructure and corrosion behavior of nickel-based alloys in hydrochloric acid	57
Multi-stage hot deformation and dynamic recrystallization behavior of low-cost Ti–Al–V–Fe alloy via electron beam cold hearth melting	57
SiC fibers with different diameters exhibiting excellent high-temperature resistance and oxidation resistance	57
Microstructure evolution and its influence mechanism on strength-plasticity of Al7075 sheets during hot multi-DoF forming	57
Atomic simulation study on the effect of Y atom and grain boundary on tensile deformation in polycrystalline magnesium alloy	57
Effect of mixing method and particle size on hardness and compressive strength of aluminium based metal matrix composite prepared through powder metallurgy route	57
Exploring the creep and oxidation behaviors of four types of FeCrAl alloys through small punch test at 600 °C: Experiments and simulations	57
Effect of pulse gas tungsten arc welding on the metallurgical characteristics & microstructural evolution in AZ31B magnesium alloy welds	57
Experimental and numerical simulation study on microstructure, residual stress and mechanical properties of Fe–Mn–C–Cr cryogenic high-manganese steel arc-welded joint	56
Modeling and simulation of the negative angle cutting with a combined constitutive model for U71Mn rail steel	56
Enhanced high-temperature deformation compatibility of an austenite-ferrite duplex microstructure in medium-Mn steel	56
Mechanism of liquid film migration and interface reaction in multi-layer aluminum sheets during brazing based on the homogenization annealing	56
Eliminating fluoride-induced corrosion of aluminum cathodes in zinc electrowinning by aluminum ion complexation	56
Effect of laser offset on microstructure and mechanical properties of Nb521/TA15 dissimilar joints	56
Parameter optimization and tensile properties of additively manufactured lattice structures of Ti6Al4V alloy	56
Study on self-sharpening mechanism of porous diamond abrasive grain based on discrete element simulation	56
Experimental investigation and machine learning modeling using LSTM and special relativity search of friction stir processed AA2024/Al2O3 nanocomposites	56
Effect of shot peening on residual stress stability and high-temperature mechanical properties of powder metallurgy Ni-based superalloy	56
Corrosion behavior of irradiated FeCrAlY coatings in oxygen-deficient and flowing Lead-bismuth Eutectic	56
Hot deformation behavior, microstructure evolution and slip system of Mg-2Zn-0.5Mn-0.2Ca alloy	55
Microstructure and wear resistance of TiC-reinforced high carbon wear-resistant steel after heat treatment	55
Orientation relationships and interface structure between Al11Ce3 and Al in Al–Ce eutectic	55
In-situ fabrication of Ce-doped CuAl-LDH@Ce composite superhydrophobic coating on 2219 aluminum alloy: Self-healing anti-corrosion performance and mechanism investigation	55
Study on the effect of solution treatment on mechanical and corrosion properties of SAF 2507DSS produced by LPBF	55
Machine learning guided constitutive model and processing map for Fe2Ni2CrAl1.2 multi-principle element alloys	55
Effect of long-term thermal exposure on the microstructure and mechanical properties of a new cast nickel-base superalloy	55