Journal of Materials Research and Technology-JMR&T

Papers
(The H4-Index of Journal of Materials Research and Technology-JMR&T is 91. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)
ArticleCitations
Accelerated testing of soft soldered, small-diameter, thin-walled CuNi pipes subjected to cyclic internal pressure loading933
Models for plastic flow: People, places, concepts and techniques710
Effect of Ni and Nb concentration on microstructural evolution in a 20Cr ferritic alloy strengthened by Ni16Nb6Si7-G phase485
Interaction of displacement cascades with {10 1351
Electron microscopic investigation of precipitation hardening in Al-Si based alloys335
Effect of heating and bending on localized critical current in 2G HTS tapes with non-contact trapped field measurements284
In-situ observation of twinning and grain rotation assisted deformation in wire-arc direct energy deposited (WDED) single phase titanium245
Near-surface self-resistance hydrogen effect of eutectic high-entropy alloy AlCoCrFeNi2.1228
Utilization of rice straw as an inhibitor of strength deterioration of sulfide-rich cemented paste backfill223
Microstructure evolution and property strengthening of CuCr50 prepared by thermite reduction-electromagnetic casting during the heat treatment process221
Effect of Al2O3 particle content on microstructure and mechanical properties of 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding217
(La0.2Dy0.2Nd0.2Sm0.2Eu0.2)2GdTaO7: a promising candidate oxides for high-temperature coating applications217
Structural evolution of PVP@Ag nanowires induced by focused electron beam irradiation: The passivation effect of PVP217
Investigation of copper and zinc alloy surface exposed to corrosion environment by digital image processing215
Enhanced mechanical properties of Zr65Cu15Ni10Al10 bulk metallic glass by simultaneously introducing surface grooves and multiple shear bands212
SiC fibers with different diameters exhibiting excellent high-temperature resistance and oxidation resistance212
The interrupted hot compression of an as-forged titanium matrix composite: flow softening behavior and deformation mechanism199
Low cycle fatigue properties assessment and damage influence on DP 500/800 steel sheet190
Toward single crystal nickel fabrication using WAAM – A first report186
Strain-induced fabrication of anisotropic nanopores by in-situ E-beam irradiation181
Adaptability analysis of H2-rich gas injection and sintered ore performance with different raw material ratios167
Predicting mechanical properties of bainitic rail steels based on microstructure digitalization and machine learning166
Microstructure and mechanical properties analyses of Ti(C, N)–Fe/low-carbon steel composite material165
Melt-based additive manufacturing of refractory metals and alloys: Experiments and modeling164
An integrated exploration from microstructure to mechanics in austenite to pearlite transformation of high carbon steel under high magnetic fields164
Oxidation behaviors of a Ni–Cr–W based superalloy with different microstructures162
A high-strength binary Mg-1.2Ce alloy with ultra-fine grains achieved by conventional one-step extrusion during 300–400 °C159
Prediction of titanium burn-off and untimate titanium content in electroslag process156
Corrigendum to ‘Study on laser cladding and properties of AZ63-Er alloy for automobile engine’ [Source J Mater Res Technol-JMR&T 9 (3), (May–June 2020) Pages 5154–5160]155
Corrigendum to “Study on the surface properties of the regenerated polyurethane foam micropowder via cryogenic pulverization and its application” [J Mater Res Technol 23 (2023) 808–818]154
Corrigendum to “Melting behavior of in-flight particles in ultra-high speed laser cladding” [J Mater Res Technol 24 (2023) 7047–7057]153
Microstructures and mechanical properties of additively manufactured Fe–21Mn-0.6C TWIP steel using laser powder bed fusion144
Corrigendum to ‘The regolith-hosted clay REEs leaching effects by mechanical grinding and at low temperature: An analogy on treatment method’ [J Mater Res Technol 37 (2025) 2338–2351]144
A eutectic high-entropy alloy coating of novel hard-surface and soft-core structure with improved tribological properties140
Surface layer strengthening mechanism of 2060 aluminum–lithium alloy after shot-peening139
Elemental synergistic effect in CoxCrCuFeMnNi high-entropy alloys and its influence on phase and magnetic properties139
Influence of Mn on nanobainite formation kinetics and austenite retention in Al-added medium-Mn steels subjected to hybrid isothermal annealing138
Towards the preparation of organic ferroelectric composites: fabrication of a gamma-glycine-bacterial cellulose composite via cold sintering process133
Microstructure evolution and its influence mechanism on strength-plasticity of Al7075 sheets during hot multi-DoF forming129
Microstructure evolution during oxidation of quinary Ti3(AlSiSn)C2 at high temperatures and induced probable performance127
Influence of Cr content on precipitates formation and corrosion behavior of (FeNi)94-xCrx(AlTi)6 medium entropy alloys125
Dependence of microstructure evolution of novel CoreFlow™ aluminium alloy wire on wire diameter125
Effects of simulated inflammation on the encapsulation performance of medical silicone rubber coating for implantable electronic devices124
Synergistic strengthening driven by boundary-dislocation architectures in hot-rolled NiV7 alloy122
Corrigendum to ‘Microstructure, mechanical properties, and corrosion behavior of Zn-x wt. % Ti (x = 0, 0.3 and 1) alloys for biomedical applications’ [J Mater Res Technol 36 (2025) 4968–4984]120
Effect of wheel speed on the microstructure and magnetic properties of Fe-3.0 wt %Si non-oriented silicon steel ultra-thin ribbons prepared by planar flow casting119
Hot deformation behavior and microstructure evolution of K4169 nickel-based superalloy119
Mechanism of liquid film migration and interface reaction in multi-layer aluminum sheets during brazing based on the homogenization annealing118
Effect of laser offset on microstructure and mechanical properties of Nb521/TA15 dissimilar joints117
Static softening behavior of 316L stainless steel under flexible rolling process116
Parameter optimization and tensile properties of additively manufactured lattice structures of Ti6Al4V alloy115
3Y-TZP electrostatic painting to increase bond strength to dentin and dental prostheses115
Application of shot peening to improve fatigue properties via enhancement of precipitation response in high-strength Al–Cu–Li alloys115
Quantitative analysis of 3D pore characteristics effect on the ductility of HPDC Al–10Si-0.3 Mg alloy through X-ray tomography115
Revisiting the model for austenite grain size of M50 steel coupled with the carbide dissolution behavior109
Microstructural and constitutive relationship in process modeling of hot working: The case of a 60Mg-30Pb-9.2Al-0.8B magnesium alloy109
Influence of shielding gas flow on pore evolution in AlSi10Mg/In718 alloy by laser powder bed fusion107
Stress corrosion inhibition mechanism of hot rolled medium thickness Al–Zn–Mg–Cu plate by cryogenic-aging treatment106
Anisotropic deformation mechanisms in textured nanotwined Cu under shock loading106
Effect of heat treatment on microstructure and hydrogen embrittlement of additively manufactured and cast 18Ni300 maraging steel105
Study on the magnetic viscosity of multi-step magnetized heterogeneous alloys104
Dominating effects of vanadium diffusion on β↔α phase transformation in LDED Ti–6Al–4V alloy revealed by multiscale in-situ electron microscopy103
Effects of HPDC processing parameters and gating design on microstructure and properties of FeCoNiCrAl-particle-reinforced Al–Si composites103
Influence of hot isostatic pressing temperature on the hot deformation and dynamic recrystallization of a typical Ni-based powder metallurgy superalloy103
Corrigendum to ‘Coupled stress–diffusion modeling of hydrogen embrittlement in API X52 and X70 pipeline steels’ [J Mater Res Technol 41, March–April 2026, Pages 4155-4176]103
Studies on the correlation between irradiation hardening and thermal conductivity of RPV steel irradiated with protons102
Quasi-in-situ observation: study on the evolution of the brass-texture in oriented silicon steel during the process of normalizing annealing101
Unravelling age hardening behavior of multicomponent Al50Mg30Si10Cu5Zn5 alloy using TEM, APT, and SANS100
Microstructure-based 3D finite element modeling of deformation and damage of (ZrB2+B4C)/6016Al hierarchical composites99
Removal mechanism of Hydroides fouling on high-strength steel in the marine environment during nanosecond pulsed laser cleaning99
Microstructure, texture, and mechanical properties of inter-pass annealed CGPed low carbon steel after cold rolling99
High strength and high electrical conductivity Cu composites reinforced by SiO2 aerogel particles98
Simultaneous strength enhancement, melt purification, and hydrogen resistance via trace Cu/Al2Cu precipitation by controlling Cu addition in Al-5Si alloys98
Corrosion behavior of ZrO2-incorporated PEO coatings on magnesium–lithium alloy: Parameter optimization and stress-induced phase transformation98
Fabrication and characterizations of glass fiber-reinforced functional leaf spring composites with or without microcapsule-based dicyclopentadiene as self-healing agent for automobile industrial appli98
Modeling and simulation of the negative angle cutting with a combined constitutive model for U71Mn rail steel98
Effect of pulse gas tungsten arc welding on the metallurgical characteristics & microstructural evolution in AZ31B magnesium alloy welds97
Microstructural evolution and uniformity regulation in twin-roll casting Al–Mg–Si alloy plates via recrystallization annealing97
Numerical and experimental study of underwater friction stir welding of 1Cr11Ni2W2MoV heat-resistant stainless steel97
Effects of cooling manner on Laves phase precipitation and mechanical properties of Al modified super ferritic stainless steels96
Microstructure, mechanical properties and high-speed dry-cutting performance of AlCrSiCN composite coatings96
Deformation mechanism and resultant microstructural characteristics in extruded dilute Mg-0.1Bi-0.1Sn alloy with bimodal-sized grain structure under compression95
Ductilization and grain refinement of AA7075-T651 alloy via stationary shoulder friction stir processing95
Quantized synaptic characteristics in HfO2-nanocrystal based resistive switching memory95
High-temperature radiation resistance of NiCoFe medium-entropy alloy enabled by stable nanostructures and defect evolution mechanisms94
Experimental investigation on wear resistance and corrosion behavior of nickel-aluminum bronze alloy fabricated by wire-arc additive manufacturing94
Evolution mechanism of grain orientation and texture distribution of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si alloy under electroshocking treatment93
Bioinspired fibrous microstructure breaks strength and toughness trade-off in plain carbon steel92
Influence of ω and secondary α phase transformation on high-cycle fatigue behavior of Ti–2Al-9.2Mo–2Fe alloy92
Mechanical performance improvement for various 9Cr ODS alloys at room temperature and 650 °C by tailoring hot rolling and subsequent heat treatments92
Investigation of defect control in selective laser melted La–Fe–Co–Si alloys through energy optimization and thermal modeling91
Effect of shot peening on residual stress stability and high-temperature mechanical properties of powder metallurgy Ni-based superalloy91
Solute segregation and interface stability in ODS ferritic alloys: A first-principles study with experimental validation91
0.52051401138306