OOIR: Observatory of International Research

Papers

(The H4-Index of Case Studies in Thermal Engineering is 66. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-06-01 to 2026-06-01.)

Article	Citations
Performance assessments of cascade refrigeration system with expander boosted subcooling	255
Characteristics of motor temperature distribution in plateau	214
Maximizing photovoltaic thermal system through computational fluid dynamics-driven multi-factor parametric optimization: A Taguchi-grey relational analysis method to enhancing electrical output and co	169
Effect of ultrasonic on thermo-hydraulic characteristics of shell and tube heat exchangers with twisted tape	165
Experimental studies on sidewall pool fire for assessing green façades hazard	155
Investigating cold energy retention in advanced storage systems with complex geometries	149
Study of thermal behavior on multi-tank cascade system for ship-borne hydrogen storage tank using a new design configuration	138
Analysis of heat transfer in n	135
Three-dimensional analysis of thermohydraulic performance in corrugated channels with embedded baffles: Optimization of heat transfer and energy efficiency	133
Enhancing heat exchanger design using autoencoder model for predicting efficiency and cost in chemical processing	127
Harnessing fuel cell and PVT for cogeneration in buildings: A comparative analysis in different climates	127
Study of geometrical influence on heat transfer characteristics in a cross-wavy primary surface heat exchanger regarding thermal resistance method	119
An experimental study on the agitating efficiency and power consumption for viscoelastic-based nanofluids: Elasticity, impeller effects, and artificial neural network approach	112
Numerical investigation of the effect of hot and cold fluids on dental implants made of different materials	112
Adjustment algorithm of damper openings of tangentially fired boilers based on secondary air distribution	109
Order degree and centrality analysis of advanced fighter environmental control system and thermal management system	104
Conjugate gradient method with regularization in estimating mold surface heat flux during continuous casting	103
Experimental investigation of biodiesel powered engine coupled refrigeration for remote areas' vaccine storage	103
Improve the performance of cold crucible used for emissivity measurement of molten metal	101
Investigation on steady-state temperature field by a novel laminated tooth for multi-tooth in harmonic gear drive	101
Forecasting the temperature of a building-integrated photovoltaic panel equipped with phase change material using artificial neural network	100
Study of heat transfer performance of miniature heat sink for integrated circuit packaging field	99
Optimization of the performance and operation of a photovoltaic-thermoelectric power supply system for bridge safety monitoring microsystems	99
Intelligent deep learning analysis of MHD williamson ternary hybrid nanofluid thin film transport with heat and mass transfer under multiple slip effects	98
Case study of natural convection topology optimization based on finite volume method	97

Thermal performance enhancement and assessment of a double-pass solar air heater using perforated vertical V-baffles and semi-circular ducts	97
Development of an empirical correlation to predict the effectiveness of heat and mass transfer from textiles in a rotating drum	96
Neural network model for fast prediction of infrared radiation of turbofan engine with axisymmetric exhaust system in preliminary design phase	96
Kinetic analysis and calculation correction methods for moisture evaporation rate in pine lignocellulosic biomass	91
Thermal error prediction model of high-speed motorized spindle based on DELM network optimized by weighted mean of vectors algorithm	90
Enhancing the ignition and combustion characteristics of aluminum-based nanofluid fuels via graphene oxide	89
Analysis of billet temperature non-uniformity in a regenerative reheating furnace: Considering periodic combustion switching and misalignment contact of walking beams	88
Thermal optimization of heat pipes with multi-walled carbon nanotubes and aluminum oxide nanofluids	87
Research on efficient numerical method of air flow and heat transfer in a refrigerated truck	87
Experimental study on the influence of base plate temperature and fin pitch on frosting characteristics of parallel cold plates	85
Rapid pyrolysis of low rank coal: dynamic modeling and parameter analysis of a novel solid heat carrier in a co-current downer reactor	81
An in-depth analysis of residential E-cooling demand in The Netherlands	80
Unveiling thermal and hemodynamic effects of aneurysm on abdominal aorta using power law model and finite element analysis	79
Numerical investigation of the self-propulsion mechanism of a droplet on a hot ratchet surface	79
Numerical modeling of wall-to-cluster heat transfer in swirling fluidized beds based on MFiX-DEM approach	78
Numerical simulation and geometric optimization of a desalination system using solar energy using two-phase mixing method with alumina nanoparticles	78
Performance comparison of LFPSC-ASHP and VTSC-ASHP heating systems based on oil and gas gathering and transportation stations	77
Numerical simulation of interior ballistics two-phase flow in modular charge based on the particle element method	76
Energy and thermodynamic analysis of a typical cement production system based on experimental and simulated investigations	76
A coupling ventilation and refrigerating research for car cabin	76
Numerical and experimental investigation of a novel hybrid indirect-direct evaporative cooling system with enhanced humidity regulation: A case study in hot-humid conditions	75
Phase change regulation and enhanced enthalpy in mixed tetrabutylammonium salt hydrates for multi-temperature cold storage applications	75
Corrigendum to “Integrated thermal management enabling 0.1 K uniformity in meter-scale blackbody radiation source over broad temperature ranges” [Case Stud. Therm. Eng. 75 (2025) 107252]	74
Heat transfer modelling of thermal anti-freezing method for ice hot-point drilling	72
Third-order isogeometric analysis for vibration characteristics of FGP plates in the thermal environment supported by Kerr foundation	72
Thermal investigation of a thermoelectric cooler based on Arduino and PID control approach	72
Research on magnetic-fluid-thermal-stress multi-field bidirectional coupling of high speed permanent magnet synchronous motors	71
Analysis on Cattaneo-Christov heat flux in three-phase oscillatory flow of non-Newtonian fluid through porous zone bounded by hybrid nanofluids	71
Hybrid geometric optimization of wavy tubes with Y-shaped fins for enhanced solidification in latent heat storage systems	71
Numerical analysis of thermal resistivity impact on magnetohydrodynamic squeezing flow of Casson ternary nanofluid with chemical reaction	70
Study on temperature gradient of ultra-thick foam sandwich composite structure during curing	68
Centerline temperature distribution of compartment spray fire under limited ceiling ventilation	68
Entropy formation in second grade nanofluid flow across a curved surface with the impact of activation energy and chemical reaction	68
Numerical investigation of the effects of geometric and fluid parameters on the thermal performance of a double -tube spiral heat exchanger with a conical turbulator	67
Machine learning-based Nusselt number prediction for falling-film evaporators in absorption refrigeration systems	67
Mechanical properties and mechanism of carbonated coal gangue concrete after elevated temperatures	67
Artificial intelligence aided microwave coagulation therapy: Analysis of heat transfer to tumor tissue via hybrid modeling	66
Study on thermo-mechanical properties of energy piles based on the improved exponential model	66
A comprehensive analysis of flow and heat transfer performance in a novel Tesla valve microchannel	66
Oblique microchannel merged with circle micro pin-fin as a novel hybrid heat sink for cooling of electronic devices	66
Enhancing solar still operation through rounded corrugated walls and basin with wick material, reflectors, and external condensation	66
Design and development of a test platform for a power transformer using biodegradable dielectric liquid cooling	66
Optimizing engine performance with piston thermal barrier coatings and Juliflora biodiesel–diesel blends: A response surface methodology approach	66