Journal of Asian Ceramic Societies

Papers
(The TQCC of Journal of Asian Ceramic Societies is 6. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-11-01 to 2025-11-01.)
ArticleCitations
Impedance spectroscopy technique for estimating the oxidation of the PyC interphase layer in a SiCf/SiC ceramic matrix composite40
Enhancing Na ion conductivity of Na chloride cathode material NaFeCl 4 through polyatomic anion substitution30
Macroporous bioceramic scaffolds based on tricalcium phosphates reinforced with silica: microstructural, mechanical, and biological evaluation30
Magnetically separable CeO 2 /CoFe 2 O 4 heterojunction photocatalysts for dye degradation: cha27
Effect of sintering temperature on physical, mechanical, and electrical properties of nano silica particles synthesized from Indonesia local sand for piezoelectric application20
High-voltage insulation and dielectric properties of ceramic-glass composites19
Characterization of slurries for slip casting via constant pressure filtration: determination of the most suitable slurry property for controlling the green-body density18
Enhancing the thermal shock resistance of Al2O3-SiC-C castables via the generation of in-situ SiC whiskers15
Crystallite size and phase purity in Pb 1-x Sr x TiO 3 ferroelectric perovskites for biomedical14
Enhanced electrical and energy harvesting performances of lead-free BMT modified BNT piezoelectric ceramics14
Dependence of local atomic structure on piezoelectric properties of PbZr1−xTixO3 materials14
Enhancing the optical and photoelectric efficiency of PEDOT/PSS thin film by incorporating activated biochar for photovoltaic applications14
Effect of aprotic solvent on characteristics of Al2O3 ceramic hollow fiber substrates prepared by phase inversion for hydrogen permeation applications13
Effect of sintering temperatures on temperature coefficient of capacitance of KCa2Nb3O10 bulk-layered perovskite12
Effect of CeO 2 -Y 2 O 3 sintering aids on the microstructure and properties of corundum-based 12
Effect of CNT addition and its orientation on thermal shock resistance of B4C/CNT composites fabricated by hot-pressing12
Effect of magnesium oxide in multiphase additive on the formation process and morphology of β-Si3N4 whisker12
Microhardness and microstructural properties of a mixture of hydroxyapatite and β-tricalcium phosphate11
In-situ TiC-reinforced Ni-based composite coatings fabricated by ultrasonic-assisted electrospark powder deposition10
The effects of Ba0.85Ca0.15Zr0.1Ti0.9O3 addition on the phase, microstructure, and thermoelectric properties of Ca3Co4O10
High energy-storage performance under low electric fields and enhanced electric-field-induced strain in Nb 5+ doped BNT−BT lead-free piezoceramics10
A Synergic Effect of Bi-metallic Layered Hydro-Oxide Cocatalyst on 1-D TiO2 Driven Photoelectrochemical Water Splitting9
Structural evolution, ferroelectric phase transitions, and dielectric behavior of Sn-doped Ba 0.95 Sr 0.05 TiO 3<9
Influence of MgO-Al 2 O 3 hollow sphere content on the microstructure and mechanical properties of calcium hexaluminate porous cer9
Preparation of novel cosmetic white pigments by mechanochemical treatment of zinc oxide with phosphoric acid9
Preparation and properties of HfB2-HfC and HfB2-HfC-MoB composites by reactive spark plasma sintering8
Temperature- and electric field-dependence of polarization hysteresis for a [001]c poled PMN-PT single crystal8
Oxyfluorides for electrochemical and photoelectrochemical water oxidation: a review and basic tutorial8
In-situ formation of Zn-MOF coating on MgO/HA composite layer produced by plasma electrolytic oxidation on Mg-Sn-Mn-Ca alloy for orthopedic internal fixation devices8
Development and Characterization on the Isothermal Kinetics of Mg(OH)2-sol Synthesized by Chemical Method8
Correlation between phase, microstructure and electrical properties of Ba 0.7 Sr 0.3 TiO 3 -mod8
Synthesis of PbTiO3 nanoplates by two-step hydrothermal method with pH-adjusting agent of ammonia solution8
Hydrostatic piezoelectric properties of 1-3 type piezo-composite with a porous polymer matrix8
Ultra-low temperature sintering and microwave dielectric properties of Mg-substituted SrCoV2O7 ceramics7
Effects of surface roughness of AlN ceramic substrate on the interface mechanical behavior of AlN/Ag structures7
Preparation of Fe2AlB2 material via thermal explosion induced by spark plasma sintering7
Effects of adding alloying elements to nickel on the hardening of WC–Ni cemented carbides7
Synthesis of BaTiO 3 /Ag nanocomposites using a sonochemical process and low-temperature sintering7
Synthesis of multi-type rare earth compounds with RE(OH)SO4 as a new sacrificial-template and photoluminescence6
Preparation and properties of metakaolin-based porous geopolymer formed with sodium perborate6
Resistive switching behaviors of oxygen-rich TaOx films prepared by reactive magnetron sputtering6
Facile synthesis of zinc hydroxyfluoride nanobelt and effect of hexamethylenetetramine for growth direction6
Development of oxide-based all-solid-state batteries using aerosol deposition6
Parametric estimation analysis of compressive stress effects on piezoelectric properties of PZT ceramic6
Investigating the ultralow dielectric loss of spinel-like and modified orthorhombic perovskite ceramic structures for microwave applications6
Digital light processing 3D printing of surface-oxidized Si3N4 coated by silane coupling agent6
Effect of silver/zinc co-dopant on enhancing cytotoxicity and antibacterial property of spray pyrolyzed bioactive glasses6
Evaluation of surface characteristics and natural radioactivity of mineral-based glaze according to zircon substitution6
Study on the correlation between radioactive counting time and measurement uncertainty of ceramic materials6
Tailoring the optical parameters of CuO nanoparticles via Ni and Co co-doping6
Enhanced energy storage and fast discharge properties of BaTiO3-Bi(Ni0.5Zr0.5)O3 ceramics modified by (Bi0.5Na0.5)0.7Sr6
TiO 2 phase-controlled synthesis of Li-La-TiO solid electrolytes for advanced all-solid-state batteries6
Effect of laser surface texturing on friction performance and surface damage of silicon nitride ceramic6
0.17633080482483