OOIR: Observatory of International Research

Papers

(The H4-Index of Journal of Central South University is 32. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Optimized joint repair effects on damage evolution and arching mechanism of CRTS II slab track under extreme thermal conditions	88
Hollow structured SnO2/NxC composites: Preparation approach and promising performance in lithium-ion battery	65
One-pot alternating current synthesis of SnO2 based composite with enhanced diffusion kinetic behaviors for lithium-ion batteries	64
Investigation of precursor criterion of coal dynamic instability from energy perspective	62
Numerical simulation of intensive quenching process and experimental validation for 40Cr	61
Innovative pillar recovery method integrating gob-side entry driving and directional roof-cutting for thick-hard roof coal seams	60
Experimental studies and failure mechanisms of strain and fault-slip rockburst: A review	57
Microstructure evolution and mechanical properties of 2195 Al-Li alloy with different heat-treatment states via friction stir additive manufacturing	56
Construction of dicyandiamide-coated manganese dioxide composite and its mechanism for improving zinc storage performance	47
Stainless steel anisotropic superhydrophobic surfaces fabrication with inclined cone array via laser ablation and post annealing treatment	46
Influence of the synergistic effect of rare-earth biphasic particles on wear properties of high-entropy alloy coatings prepared by extremely high-speed laser cladding	46
Seepage characteristics test of carbonaceous mudstone soil-rock mixture considering rock content and rainfall infiltration angle	45
Crack propagation behavior in sandstone during unloading confining pressure under different seepage pressures	44
Static compressive mechanical properties and disturbed state concept-based theoretical model of gypsum rocks with coupled influences of wet-dry cycles and flow rates	44
Bearing characteristics and safety control of hydraulic support groups in shallow-buried thin bedrock ultra-long working faces	44
Evaluation of the slipstream in different regions around a train with respect to different nose lengths: A comparison study	41
Characteristics of subgrade soil resilient modulus considering wide-range stress state	39
Numerical investigation of friction stir welding parameters on microstructure, thermal and mechanical properties of ultrafine-grained Al-0.2 wt% Sc alloy sheet	39
Experimental study on mechanical behavior and microscopic damage evolution of sandstone subjected to freeze-thaw cycles	38
Microstructure and corrosion properties of micro-beam plasma remelted Mg-12Dy-1.1Ni alloy	38
Dynamic behaviors and mitigation measures of a train passing through windbreak transitions from ground to cutting	37
Mechanism, prevention, and control of mining-induced dynamic disasters in underground metal mines in China: Challenges and solutions	36
Undercutting mechanism of worm wheel in offsetting normal arc-toothed cylindrical worm drive	36
Visualization detection of slurry transportation pipeline based on electrical capacitance tomography in mining filling	36
Optimal design of automotive body B-pillar using simplified finite element model of body-in-prime combined with an optimization procedure	34

Metal-organic framework-derived porous carbon for the advanced aqueous zinc-ion hybrid capacitor	34
Towards early rockburst susceptibility assessment: A simple approach combining acoustic emission and uniaxial compression tests	34
Comprehensive utilization of spodumene ore through pyrometallurgical process with Fe2O3 addition	33
Band gap modulation of nanostructured WO3 nanoplate film by Ti doping for enhanced photoelectrochemical performance	33
Microseismic energy and intensity criterion of rockburst in deep TBM tunnels: A case study of the Neelum-Jhelum hydropower project	33
Strength and damage evolution mechanism of rock mass with holes under cyclic loading	32
Laser surface functionalization to achieve extreme surface wetting conditions and resultant surface functionalities	32
Interfacial optimization enabling reversible and stable aqueous zinc metal batteries under harsh conditions	32
Removal of arsenic from arsenic-containing solution in a three-dimensional electrode reactor	32
Risk adjustable optimal operation for electricity-hydrogen integrated energy system based on chance constrained goal programming	32