Energy Science & Engineering

Papers
(The median citation count of Energy Science & Engineering is 2. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-11-01 to 2024-11-01.)
ArticleCitations
How green is blue hydrogen?449
Ionic conductivity and ion transport mechanisms of solid‐state lithium‐ion battery electrolytes: A review168
Progress in proton‐conducting oxides as electrolytes for low‐temperature solid oxide fuel cells: From materials to devices120
Effects of different environmental and operational factors on the PV performance: A comprehensive review107
A brief review of electrocatalytic reduction of CO2—Materials, reaction conditions, and devices80
Safety challenges and safety measures of Li‐ion batteries66
Performance enhancement of a solar still using magnetic powder as an energy storage medium‐exergy and environmental analysis58
A novel long term solar photovoltaic power forecasting approach using LSTM with Nadam optimizer: A case study of India54
Back contacts materials used in thin film CdTe solar cells—A review44
A novel hybrid algorithm based on rat swarm optimization and pattern search for parameter extraction of solar photovoltaic models41
Strategies for improving photoelectrochemical water splitting performance of Si‐based electrodes40
Influences of hydrogen addition from different dual‐fuel modes on engine behaviors39
Low‐carbon economic operation for integrated energy system considering carbon trading mechanism38
Regulation and impact of VOC and CO2 emissions on low‐carbon energy systems resilient to climate change: A case study on an environmental issue in the oil and gas industry33
A conceptual review of sustainable electrical power generation from biogas32
Optimization of fuzzy control energy management strategy for fuel cell vehicle power system using a multi‐islandgenetic algorithm32
Comparative experimental study on macroscopic spray characteristics of various oxygenated diesel fuels31
Degradation issues and stabilization strategies of protonic ceramic electrolysis cells for steam electrolysis30
Monitoring of renewable energy systems by IoT‐aided SCADA system30
Maximum power point tracking algorithms for wind power generation system: Review, comparison and analysis28
Artificial neural networks model for predicting the behavior of different injection pressure characteristics powered by blend of biofuel‐nano emulsion28
CO2 reduction into formic acid under hydrothermal conditions: A mini review26
Hybrid energy storage system topology approaches for use in transport vehicles: A review26
Economic, Environmental and Social Impact of Carbon Tax for Iran: A Computable General Equilibrium Analysis26
Comment on “How green is blue hydrogen?”25
Role of Ca, Cr, Ga and Gd promotor over lanthana‐zirconia–supported Ni catalyst towards H2‐rich syngas production through dry reforming of methane25
Defect object detection algorithm for electroluminescence image defects of photovoltaic modules based on deep learning25
Critical review of multigeneration system powered by geothermal energy resource from the energy, exergy, and economic point of views25
Techno‐economic optimization of a grid‐connected hybrid energy system considering electric and thermal load prediction24
Optimal scheduling of DG and EV parking lots simultaneously with demand response based on self‐adjusted PSO and K‐means clustering24
An enhanced multi‐objective differential evolution algorithm for dynamic environmental economic dispatch of power system with wind power24
Thermohydraulic performance improvement and entropy generation characteristics of a microchannel heat sink cooled with new hybrid nanofluids containing ternary/binary hybrid nanocomposites24
Space cooling using geothermal single‐effect water/lithium bromide absorption chiller23
Multiphase layered transition metal oxide positive electrodes for sodium ion batteries23
An ultra‐short‐term wind speed prediction model using LSTM based on modified tuna swarm optimization and successive variational mode decomposition23
Deformation and damage of cement sheath in gas storage wells under cyclic loading23
Twin‐model framework development for a comprehensive battery lifetime prediction validated with a realistic driving profile22
Forecasting carbon dioxide emission price using a novel mode decomposition machine learning hybrid model of CEEMDAN‐LSTM22
Direct internal methane reforming in biogas fuelled solid oxide fuel cell; the influence of operating parameters22
Application of Al2O3/water nanofluid as the coolant in a new design of photovoltaic/thermal system: An experimental study22
Prediction of remaining useful life for lithium‐ion battery based on particle filter with residual resampling21
Enhanced social network search algorithm with powerful exploitation strategy for PV parameters estimation21
Numerical simulation of the stress field and fault sealing of complex fault combinations in Changning area, Southern Sichuan Basin, China20
Repair options for PV modules with cracked backsheets20
Validation study of no‐pillar mining method without advance tunneling: A case study of a mine in China20
Conversion of waste to sustainable aviation fuel via Fischer–Tropsch synthesis: Front‐end design decisions20
Interaction mechanism between cellulose and hemicellulose during the hydrothermal carbonization of lignocellulosic biomass20
Sustainable development of China's smart energy industry based on artificial intelligence and low‐carbon economy20
Application of ultrathin TiO2 layers in solar energy conversion devices20
Nonlinear modeling and operation stability of variable speed pumped storage power station19
Deconvolution approach for floating wind turbines19
Characterization and kinetic modeling for pyrolytic conversion of cotton stalks18
Determination of coal pillar width for gob‐side entry driving in isolated coal face and its control in deep soft‐broken coal seam: A case study18
Solar‐light‐driven ZnO/biochar treatment of pesticides contaminated wastewater: A practical and computational study18
Life cycle analysis of greenhouse gas emissions of China's power generation on spatial and temporal scale17
Analysis and optimization of concentrated solar power plant for application in arid climate17
A multigroup marine predator algorithm and its application for the power system economic load dispatch17
Multi‐objective optimal planning of EV charging stations and renewable energy resources for smart microgrids17
Determination of the heat capacity of cellulosic biosamples employing diverse machine learning approaches16
A study on the fuzzy evaluation system of carbon dioxide flooding technology16
Improvement of microbial fuel cell performance using novel kaolin earthenware membrane coated with a polybenzimidazole layer16
Salt hydrates as phase change materials for photovoltaics thermal management16
The Connection between flow pattern evolution and vibration in 90‐degree pipeline: Bidirectional fluid‐structure interaction15
Fracturing and production analysis of the efficacy of hydraulic fracture stage reduction in the improvement of cost‐effectiveness in shale oil development: A case study of Jimsar shale oil, China15
Mining‐induced failure characteristics and surrounding rock control of gob‐side entry driving adjacent to filling working face in the deep coal mine15
Dynamic simulation of a solar ejector‐based trigeneration system using TRNSYS‐EES co‐simulator15
Solar photovoltaic potential and diffusion assessment for Pakistan15
Experiment and failure mechanism of cement sheath integrity under development and production conditions based on a mechanical equivalent theory15
Feasibility evaluation of an off‐grid solar‐biomass system for remote area electrification considering various economic factors15
Experimental investigation on the application of carbon dioxide adsorption for a shale reservoir14
Rapid evaluation and optimization of carbon dioxide‐enhanced oil recovery using reduced‐physics proxy models14
Review on low carbon planning and operation of integrated energy systems14
Design and research of permanent magnet synchronous motor controller for electric vehicle14
Techno‐economic assessment and sensitivity analysis of biodiesel production intensified through hydrodynamic cavitation14
Experimental based comparative exergy analysis of a spark‐ignition Honda GX270 Genset engine fueled with LPG and syngas14
Numerical simulations of depressurization‐induced gas production from hydrate reservoirs at site GMGS3‐W19 with different free gas saturations in the northern South China Sea14
Decarbonization potential of future sustainable propulsion—A review of road transportation14
Comprehensive assessment of heat pump dryers for drying agricultural products14
Effects of hydrophilic and hydrophobic nano‐CaCO3 on kinetics of hydrate formation14
Spatiotemporal evolution of coal spontaneous combustion in longwall gobs: A case study from mining discontinuation to resumption14
Selection of the ultimate perovskite solar cell materials and fabrication processes towards its industrialization: A review14
Nonlinear modeling of hydroturbine dynamic characteristics using LSTM neural network with feedback13
Field and simulation study of the rational retracement channel position and control strategy in close‐distance coal seams13
4E analysis of the horizontal axis wind turbine with LCA consideration for different climate conditions13
Bi‐level optimization of the integrated energy systems in the deregulated energy markets considering the prediction of uncertain parameters and price‐based demand response program13
Evaluation of research and development subsidies and fossil energy tax for sustainable development using computable general equilibrium model13
In situ synthesis of heterogeneous NiSe2/MoSe2 nanocomposite for high‐efficiency electrocatalytic hydrogen evolution reaction13
Energy characteristics of sandstones with different crack angles under true triaxial cyclic loading and unloading13
Microgrid to smart grid's evolution: Technical challenges, current solutions, and future scopes13
Gas seepage laws based on dual porosity and dual permeability: Numerical simulation and coalbed methane extraction practice13
Risk‐averse scheduling of an energy hub in the presence of correlated uncertain variables considering time of use and real‐time pricing‐based demand response programs13
Optimal operation of a smart railway station based on a multi‐energy hub structure considering environmental perspective and regenerative braking utilization13
Techno‐economic analysis and energy performance of a geothermal earth‐to‐air heat exchanger (EAHE) system in residential buildings: A case study13
Energy and exergy assessment with updated Reistad estimates: A case study in the transportation sector of Bangladesh13
Fault detection through discrete wavelet transform in overhead power transmission lines13
Measurement of wellbore leakage in high‐pressure gas well based on the multiple physical signals and history data: Method, technology, and application13
Participation of electric vehicles in auxiliary service market to promote renewable energy power consumption: Case study on deep peak load regulation of auxiliary thermal power by electric vehicles13
Operation optimization of integrated energy systems based on heat storage characteristics of heating network13
An experimental and numerical investigation into using hydropower plant on oil transmission lines13
Environmental and damage assessment of transparent solar cells compared with first and second generations using the LCA approach13
A machine learning‐based approach to the multiobjective optimization of CO2 injection and water production during CCS in a saline aquifer based on field data12
Performance study of centrifugal air compressor for proton exchange membrane fuel cell systems12
Preventing sour gas kicks during workover of natural gas wells from deep carbonate reservoirs with anti‐hydrogen sulfide fuzzy‐ball kill fluid12
Energy, exergy, economic, and environmental (4E) analyses and optimization of a CCHP system with steam turbine12
Impacts of fluorine in NASICON‐type materials as cathodes for aqueous zinc ion batteries12
Adaptive slime mould algorithm for optimal design of photovoltaic models12
Defect identification of wind turbine blade based on multi‐feature fusion residual network and transfer learning12
A universal anisotropic model for a lithium‐ion cylindrical cell validated under axial, lateral, and bending loads12
Simulation of a parabolic trough solar collector containing hybrid nanofluid and equipped with compound turbulator to evaluate exergy efficacy and thermal‐hydraulic performance12
Techno‐economic comparison of amine regeneration process with heat‐stable amine salt reclaiming units12
Reply to comment on “How Green is Blue Hydrogen?”12
Recent progress in electrochemical reduction of carbon dioxide on metal single‐atom catalysts12
Piezoelectric method‐based harvested energy evaluation from car suspension system: Simulation and experimental study12
Evaluation of the solidification process in a double‐tube latent heat storage unit equipped with circular fins with optimum fin spacing12
The green total factor productivity and convergence in China11
Internal benefit optimization model of gas‐thermal power virtual power plant under china's carbon neutral target11
Indoor light energy harvesting for battery‐powered sensors using small photovoltaic modules11
A hybrid deep learning approach by integrating extreme gradient boosting‐long short‐term memory with generalized autoregressive conditional heteroscedasticity family models for natural gas load volati11
Carbon dioxide utilization: A critical review from multiscale perspective11
Deformation and stress analysis of cup on pipeline inspection gauge based on reverse measurement11
Distribution characteristics of pulverized coal and stress–gas pressure–temperature response laws in coal and gas outburst under deep mining conditions11
Modified reptile search algorithm for optimal integration of renewable energy sources in distribution networks11
Electrodeposition of Ni on MWNTs as a promising catalyst for CO2RR11
Simultaneous fault diagnosis based on multiple kernel support vector machine in nonlinear dynamic distillation column11
Effects of air cooling structure on cooling performance enhancement of prismatic lithium‐ion battery packs based on coupled electrochemical‐thermal model11
Study on surrounding rock failure mechanism and rational coal pillar width of the gob‐side coal roadway under influence of intense dynamic pressure11
Development and assessment of renewable hydrogen production and natural gas blending systems for use in different locations11
Hosting capacity in distribution grids: A review of definitions, performance indices, determination methodologies, and enhancement techniques11
Numerical investigation on rock‐breaking mechanism and cutting temperature of compound percussive drilling with a single PDC cutter11
State‐of‐health estimation for lithium‐ion batteries based on partial charging segment and stacking model fusion10
The application of nonthermal plasma in methanol synthesis via CO2 hydrogenation10
Hydrothermal performance of humid air flow in a rectangular solar air heater equipped with V‐shaped ribs10
Blue hydrogen must be done properly10
Optimization on jet‐induced ventilation to enhance the uniformity of airflow distribution in data center10
A comparison of using organic Rankine and Kalina cycles as bottom cycles in a solar‐powered steam Rankine cycle10
The effect of forestry on energy efficiency in EU countries: A non‐oriented dynamic slack‐based data envelopment analysis10
Using MLP‐GABP and SVM with wavelet packet transform‐based feature extraction for fault diagnosis of a centrifugal pump10
A novel hybrid solar chimney power plant: Performance analysis and deployment feasibility10
Raising thermal efficiency of solar water‐pump using Oldroyd‐B nanofluids' flow: An optimal thermal application10
CFD analysis on optimizing the annular fin parameters toward an improved storage response in a triple‐tube containment system10
Anisotropic double‐Gaussian analytical wake model for an isolated horizontal‐axis wind turbine10
A framework for energy optimization of distillation process using machine learning‐based predictive model10
Experimental and numerical investigation of energy dissipation of roadways with thick soft roofs in underground coal mines10
Comprehensive evaluation of waterflooding front in low‐permeability reservoir10
Model for sustainable development based on system dynamics and energy–economy–environment coordination: A case study of Beijing, China10
Adaptive equivalent consumption minimization strategy for hybrid electric ship10
A novel energy optimization framework to enhance the performance of sensor nodes in Industry 4.010
Numerical investigation on sealing performance of drainage pipeline inspection gauge crossing pipeline elbows9
Experiment and numerical simulation investigation on cavitation evolution and damage in the throttling section of pressure reducing valve9
Turbulence and thermo‐flow behavior of air in a rectangular channel with partially inclined baffles9
Characteristics of in situ stress and its influence on coal seam permeability in the Liupanshui Coalfield, Western Guizhou9
Comprehensive thermoeconomic, exergoeconomic, and optimization analyses of direct oxy‐combustion supercritical CO2 intercooled and reheated cycles under design and off‐design conditions9
Prediction of methane adsorption capacity in different rank coal at low temperature by the Polanyi‐based isotherm model9
Bridging granularity gaps to decarbonize large‐scale energy systems—The case of power system planning9
Weed colonization‐based performance improvement opportunities in dual‐mixed refrigerant natural gas liquefaction process9
The influence of Ni stability, redox, and lattice oxygen capacity on catalytic hydrogen production via methane dry reforming in innovative metal oxide systems9
Evaluating the effect of using nanofluids on the parabolic trough collector's performance9
A modified model‐free‐adaptive‐control‐based real‐time energy management strategy for plug‐in hybrid electric vehicle9
Influence of cobalt chromium nanoparticles in homogeneous charge compression ignition engine operated with citronella oil9
Energy, exergy, exergo‐environmental, and exergetic sustainability analyses of a gas engine‐based CHP system9
Prediction of longwall mining‐induced stress in roof rock using LSTM neural network and transfer learning method9
Optimization of the shale gas reservoir fracture parameters based on the fully coupled gas flow and effective stress model9
Conventional and advanced exergy analyses of an organic Rankine cycle by using the thermodynamic cycle approach9
Failure mechanism and divisional differentiated control of surrounding rock in mining roadway under remaining coal pillar in close‐distance coal seam9
Study on bi‐level multi‐objective collaborative optimization model for integrated energy system considering source‐load uncertainty8
Assessment of the economic efficiency of energy‐saving projects, methodology based on simple and compound methods8
Sustainable aviation fuel: Pathways to fully formulated synthetic jet fuel via Fischer–Tropsch synthesis8
8
Critical stable sectional area of downstream surge tank of hydropower plant with sloping ceiling tailrace tunnel8
Study of the influence laws of the flow and cavitation characteristics in an injector control valve8
Research on prediction methods of formation pore pressure based on machine learning8
Transient cutting transport model for horizontal wells with a slim hole8
Reasonable stopping method and retracement channel support at fully mechanized top coal caving working face of 15 m extra‐thick coal seam: A case study8
Building energy model validation and estimation using heating and cooling degree days (HDD–CDD) based on accurate base temperature8
Vertical wind speed extrapolation model using long short‐term memory and particle swarm optimization8
Optimal stochastic energy management of electrical railway systems considering renewable energy resources' uncertainties and interactions with utility grid8
Investigating effect of polymer concentrations on separation performance of hydrocyclone by sensitivity analysis8
Experimental study of the influence of temperature and cooling method on dynamic mechanical properties and damage of granite8
A mathematical model‐based approach for DC multi‐microgrid performance evaluations considering intermittent distributed energy resources, energy storage, multiple load classes, and system components v8
Numerical simulation of complex flow structures and pressure fluctuation at rotating stall conditions within a centrifugal pump8
Analysis and assessment of a novel organic flash Rankine cycle (OFRC) system for low‐temperature heat recovery8
Effects of pore morphology and moisture on CBM‐related sorption‐induced coal deformation: An experimental investigation8
Influence of blade number on performance of multistage hydraulic turbine in turbine mode8
Experimental study on improving coalbed methane extraction by chemical treatment using acetic acid or ammonium persulfate8
Monitoring and measurement analysis of key indexes for the implementation of mining, dressing, backfilling, and controlling technology in coal resources—A case study of Tangshan Mine8
Effects of parent well spacing on the poroelastic behaviors in the infill zone in shale oil reservoirs: A case study in Jimsar Shale Oil, China8
Metal‐organic chemical vapor deposition of anatase titania on multiwalled carbon nanotubes for electrochemical capacitors8
Inverse analysis of dynamic failure characteristics of roadway surrounding rock under rock burst8
Information gap decision theory‐based electricity purchasing optimization strategy for load aggregator considering demand response8
A configuration optimization framework for renewable energy systems integrating with electric‐heating energy storage in an isolated tourist area8
An empirical study of environmental regulation on carbon emission efficiency in China8
Comparison of the influence of solid and phase change materials as a thermal storage medium on the performance of a solar chimney8
Multivariable neural network to postprocess short‐term, hub‐height wind forecasts8
Experimental study on the characteristics of wind turbine wake field considering yaw conditions8
A comprehensive framework for solar panel technology selection: A BWM‐ MULTIMOOSRAL approach7
Energy and exergy analysis of a trapezoidal absorber plate‐based solar air collector7
Enhancing potential of hydrofracturing in mylonitic coal by biocementation7
A novel non‐pillar coal mining technology in longwall top coal caving: A case study7
What does the clean energy transition look like for Russian oil exports?7
Design and performance optimization of a tri‐generation energy hub considering demand response programs7
Analysis of solar photo‐voltaic for grid integration viability in Uganda7
An interpretable BRB model with interval optimization strategy for lithium battery capacity prediction7
A novel design method of organic Rankine cycle system harvesting waste heat of heavy‐duty trucks based on off‐design performance7
Multistage carbon dioxide compressor efficiency enhancement using waste heat powered absorption chillers7
Short‐term natural gas consumption prediction based on wavelet transform and bidirectional long short‐term memory optimized by Bayesian network7
Investigation on the effect of the flow passage geometry of diesel injector nozzle on injection process parameters and engine performances7
Assessment of the thermal efficiency of subcritical power generation cycles using environmentally friendly fluids at various heat source temperatures7
Hybrid photovoltaic‐liquid air energy storage system for deep decarbonization7
Numerical investigation of corroded middle‐high strength pipeline subjected to combined internal pressure and axial compressive loading7
Numerical simulation of the non‐Newtonian fracturing fluid influences on the fracture propagation7
Stability region of hydropower plant with surge tank at HVDC sending terminal7
Experimental study on the formation characteristics of CO2 hydrate in porous media below the freezing point: Influence of particle size and temperature on the formation process and storage 7
A review on data‐centric decision tools for offshore wind operation and maintenance activities: Challenges and opportunities7
Fracture law of different overlying strata in mining of protective seam under close distance coal seam7
Optimization of wavy fin‐and‐elliptical tube heat exchanger using CFD, multi‐objective genetic algorithm and radical basis function7
Multi‐objective optimization of integrated gas–electricity energy system based on improved multi‐object cuckoo algorithm7
Anchorage weakening effect of coal roadway sidewall with different destressing borehole diameters7
A modified pulse‐decay approach to simultaneously measure permeability and porosity of tight rocks7
Numerical analysis of natural gas pressure during coal and gas outbursts7
The influence path and dynamic relationship between economic development, industrial structure upgrading, urbanization, urban–rural income gap, and electricity consumption in China7
An adaptive state of charge estimator for lithium‐ion batteries7
Effects of fracture parameters and roughness on heat‐flow coupling in rock masses with two‐dimensional fracture networks7
Material design and performance of carbon monoxide‐fueled solid oxide fuel cells: A review7
Techno‐economic analysis of PV–wind–diesel–battery hybrid power systems for industrial towns under different climates in Spain7
Heat transfer and pressure drop through mono and hybrid nanofluid‐based photovoltaic‐thermal systems7
An improved particle swarm optimization for optimal configuration of standalone photovoltaic scheme components7
Characteristics and contributing factors of major coal bursts in longwall mines7
Optimal design and experimental test of a solar simulator for solar photovoltaic modules7
A novel piezoelectric energy harvester of noncontact magnetic force for a vehicle suspension system7
Sand production behaviors during gas recovery from sandy and clayey‐silty hydrate‐bearing sediments: A comparative analysis7
Hydrofracture plugging mechanisms and evaluation methods during temporary plugging and diverting fracturing7
The effects of key rock layer fracturing on gas extraction during coal mining over a large height7
Visible light‐active pure and lanthanum‐doped copper oxide nanostructures for photocatalytic degradation of methylene blue dye and hydrogen production7
Examining the determinants of electricity consumption in the nine South African provinces: A panel data application7
A comparative study of the impact on combustion and emission characteristics of nanoparticle‐based fuel additives in the internal combustion engine6
Experimental study on the effect of injection pressure ratio on the propagation characteristics of hydrogen rotating detonation waves6
A review of hydrogen production and storage materials for efficient integrated hydrogen energy systems6
Investigation into the heat transfer models for the hot crude oil transportation in a long‐buried pipeline6
Physicochemical characteristics of biomass‐coal blend char: The role of co‐pyrolysis synergy6
Effects of SiNxrefractive index and SiO2thickness on polarization‐type potential‐induced degradation in front‐emitter n‐type crystalline‐silicon photovoltaic cell modules6
The effect of H2S on internal dry reforming in biogas fuelled solid oxide fuel cells6
A review of crude oil emulsification and multiphase flows in chemical flooding6
Design and optimization of air‐cored double‐sided linear permanent magnet generators for wave energy conversion6
Parameter identification and identifiability analysis of lithium‐ion batteries6
Study on rock mechanics characteristics of deep shale in Luzhou block and the influence on reservoir fracturing6
Computational fluid dynamic analysis of hydrogen‐injected natural gas for mixing and transportation behaviors in pipeline structures6
Exergoeconomic analysis of a pumped heat electricity storage system based on a Joule/Brayton cycle6
Research on gob‐side entry‐retaining technology with coal rib and corner strengthened support in soft rock strata6
Optical investigation on combustion and soot formation characteristics of isopropanol‐butanol‐ethanol (IBE)/diesel blends6
Preparation of energy platform chemicals by hydrothermal conversion of citrus peel6
0.058112144470215