European Journal of Environmental and Civil Engineering

Article	Citations
Compressive strength of geopolymer concrete composites: a systematic comprehensive review, analysis and modeling	53
Effects of natural zeolite and sulfate environment on mechanical properties and permeability of cement–bentonite cutoff wall	35
Estimation of the compressive strength of green concretes containing rice husk ash: a comparison of different machine learning approaches	35
Challenges and perspectives in designing engineering structures against debris-flow disaster	29
Experimental and empirical evaluation of strength for sustainable lightweight self-compacting concrete by recycling high volume of industrial waste materials	29
Effects of alternative ecological fillers on the mechanical, durability, and microstructure of fly ash-based geopolymer mortar	27
Comparative analysis of soft computing techniques in predicting the compressive and tensile strength of seashell containing concrete	25
Eco-friendly and cost-effective concrete utilizing high-volume blast furnace slag and demolition waste with lime	22
ML-EHSAPP: a prototype for machine learning-based earthquake hazard safety assessment of structures by using a smartphone app	22
A review on recycled concrete aggregates (RCA) characteristics to promote RCA utilization in developing sustainable recycled aggregate concrete (RAC)	20
Reusing plastic waste in the production of bricks and paving blocks: a review	17
Durability performance evaluation of green geopolymer concrete	16
Flexural behavior of reinforced concrete beam using CFRP hybrid system	15
Nonlinear structural performance and seismic fragility of corroded reinforced concrete structures: modelling guidelines	15
Bearing capacity-relative density behavior of circular footings resting on geocell-reinforced sand	14
Mechanism, influencing factors and research methods for soil desiccation cracking: a review	14
Friction and maximum dilatancy angles of granular soils incorporating low plastic fines and depositional techniques effects	14
Properties of sustainable self-compacting concrete made with rice husk ash	14
Behaviour of RC beams strengthened with FRP strips under combined action of torsion and bending	14
Physical and mechanical properties of metakaolin-based geopolymer mortars containing various waste powders	13
Biochar as a cost-effective and eco-friendly substitute for binder in concrete: a review	13
Neural network-based optimization of fibres for seismic retrofitting applications of UHPFRC	13
Effectiveness of using Metakaolin and fly ash as supplementary cementitious materials in pervious concrete	13
Effects of recycled tyre rubber and steel fibre on the impact resistance of slag-based self-compacting alkali-activated concrete	12
Bond properties between smooth carbon fibre-reinforced polymer bars and ultra-high performance concrete modified with polymeric latexes and fibres	12

Application of load transfer method for bored pile in loess area	12
Numerical study on the bearing capacity of strip footing resting on partially saturated soil subjected to combined vertical-horizontal-moment loading	12
State of the art on the mechanical properties of pervious concrete	12
Damage behaviours of new-to-old concrete interfaces and a damage prediction model of reinforced concrete	12
Effects of elevated temperatures on the properties of ground granulated blast furnace slag (GGBFS) based geopolymer concretes containing recycled concrete aggregate	12
Predicting changes in the mechanical properties of frozen saline soils	11
Probabilistic characteristics analysis for the time-dependent deformation of clay soils due to spatial variability	11
Temperature-dependent lateral earth pressures in partially saturated backfills	11
Flexural behavior of environmentally friendly ultra-high-performance concrete with locally available low-cost synthetic fibers	11
Crack healing in concrete by microbially induced calcium carbonate precipitation as assessed through electromechanical impedance technique	11
Improving corrosion resistance of reinforcement steel rebars exposed to sulphate attack by the use of electroless nickel coatings	11
Recent advances in blended alkali-activated cements: a review	10
Novel bond-slip model between concrete and angular CFRP fan type anchoraged CFRP strip	10
Performance of a top-down excavation in shanghai: case study and numerical exploration	9
The mechanism of alkali-aggregate reaction in concrete/mortar and its mitigation by using geopolymer materials and mineral admixtures: a comprehensive review	9
Nonlinear models to predict stress versus strain of early age strength of flowable ordinary Portland cement	9
Effect of type and volume fraction of recycled-tire steel fiber on durability and mechanical properties of concrete	9
Experimental study on the process of overtopping breach of concrete-faced sand-gravel dam	9
Laboratory investigation of cemented silt improved with bentonite and phosphogypsum in DCM walls	9
Comparative life cycle assessment (LCA) of concrete mixtures: a critical review	9
A novel true triaxial test device with a high-temperature module for thermal-mechanical property characterization of hard rocks	9
Tensile properties of bamboo strips and flexural behaviour of the bamboo reinforced concrete beams	9
Investigating impacts of deep foundation pit dewatering on land subsidence based on CFD-DEM method	9
Strength development and microstructure properties of slag activated with alkaline earth metal ions: a review study	9
Investigation of the properties and technologies of epoxy asphalt concrete preparation with the addition of fiber from fly ash of thermal power plants	9
Residual compressive strength of plain and fiber reinforced concrete after exposure to different heating and cooling regimes	8
Ground reaction curve of a circular tunnel considering the effects of the altered zone and the self-weight of the plastic zones	8
Analysis of suspension bridges in construction and completed status considering the pylon saddles	8
Mechanical and durability properties of slag/fly ash based alkali-activated concrete reinforced with steel, polypropylene and polyamide fibers	8
3D centrifuge and numerical modelling of lateral responses of a vertical loaded pile group to twin stacked tunnels	8
A new index for the strength analysis and prediction of cement-mixed soils	8
Experimental study on the shear mechanical properties of the cemented soil–concrete interface	8
Experimental study of the mechanical properties of basalt fibre-reinforced concrete at elevated temperatures	8
A simplified geopolymer concrete mix design considering five mineral admixtures	8
Large strain dynamic characteristics of quaternary alluvium sand with emphasis on empirical pore water pressure generation model	8
On the rheological, fresh and strength effects of using nano-silica added geopolymer grout for grouting columns	8
Permeation-durability properties of metakaolin blended concrete containing rubber	8
Sustainable lightweight mortar using biochar as sand replacement	8
Relation between rheological and mechanical properties on behaviour of self-compacting concrete (SCC) containing recycled plastic fibres: a review	8
Mechanical and durability properties of steel, polypropylene and polyamide fiber reinforced slag-based alkali-activated concrete	8
Experimental and numerical investigation of seismic retrofitting of RC square short columns using FRP composites	8
Effect of partial drainage on the pullout behaviour of a suction bucket foundation	8
Properties of natural pozzolan-based geopolymer concrete: effects of natural pozzolan content, type of alkaline activator, and silicate/alkali ratio	8
Numerical study on crack propagation of rock mass using the time sequence controlled and notched blasting method	8
Examination of particle shape on the shear behaviours of granules using 3D printed soil	7
Effectiveness of henna leaves extract and its derivatives as green corrosion inhibitors of reinforcement steel exposed to chlorides	7
Experimental study of fracture geometry characteristics on rock mass strength and crack propagation evolution law	7
Free desiccation shrinkage process in clayey soils	7
Theoretical analysis of the shield tunnel face stability in dry sandy strata	7
Strength and durability study of low-fines self-consolidating concrete as a pavement material using fly ash and bagasse ash	7

Effects of blending manufactured sand and offshore sand on rheological, mechanical and durability characterization of lime-cement masonry mortar	7
Behaviour of heat damaged repaired reinforced SCC cantilever beam using carbon fiber reinforced polymer rope	7
Shear behavior of reinforced concrete beams incorporating waste glass powder as partial replacement of cement	7
Closed-form solutions for large strain analysis of cavity contraction in a bounded Mohr-Coulomb medium	7
Performance evaluation of sustainable geopolymer concrete produced from ferrochrome slag and silica fume	7
Mechanical properties and environmental impact of rubberized fly ash- and red mud-based geopolymer concrete	7
Two-phase analytical model of seepage during grout consolidation around shield tunnel considering the temporal variation in viscosity and the infiltration effect	7
Cleaner production of the precast concrete industry: comparative life cycle analysis of concrete using recycled aggregates from crushed precast rejects	7
Bearing capacity of single stone column in clay using finite element limit analysis	7
Consolidation theory of homogeneous multilayer treatment by air-boosted vacuum preloading	7
Using a hybrid artificial intelligence method for estimating the compressive strength of recycled aggregate self-compacting concrete	7
Effect of the proximity of slope and pile shape on lateral capacity of piles in clay slopes	7
Comprehensive review on utilization of waste foundry sand in concrete	7
Model study on backfill grouting in shield tunnels based on fractal theory	7
Ambient cured high calcium fly ash geopolymer concrete with dolomite powder	6
Experimental investigation and analysis of pure bending plastic hinge zone in hybrid beams reinforced with high reinforcement ratio under static loads	6
Bio-fiber reinforced roller compacted concrete designed for road construction: feasibility of date palm fibers in pavements	6
Self-healing concrete: application of monod’s approach for modeling Bacillus pseudofirmus growth curves	6
Drying experiment on rammed earth structure	6
Assessment of properties of mortars modified with sugarcane bagasse ash processed by heating at different temperatures as cement replacement	6
Geosynthetic-reinforced and pile-supported embankments: theoretical discussion of finite difference numerical analyses results	6
Performance assessment of travertine waste as alternative concrete aggregate	6
Top challenges to widespread 3D concrete printing (3DCP) adoption – A review	6
Effect of slightly cadmium-enriched kenaf straw on the mechanical and thermal properties of cement mortar	5
Environmental influence on bacterial efficiency in ensuring self-healing mortars	5
Environmentally friendly viscosity-modifying agent for self-compacting mortar: Cladophora sp. cellulose nanofibres	5
A simplified approach to estimate settlements of earth embankments on piled foundations: the role of pile shaft roughness	5
An experimental and statistical investigation on the fresh and hardened properties of HFR-SCC: the effect of micro fibre type and fibre hybridization	5
Dynamic mechanical properties and constitutive model for jointed mudstone samples subjected to cyclic loading	5
Flexural behavior of high-performance and non-high-performance textile reinforced concrete composites	5
Effect of water to binder ratio and particle size distribution of waste glass powder on the compressive-strength and modulus of elasticity of normal-strength concrete	5
Effect of the alkaline solution concentration on swelling performance of MX80 granular bentonite	5
Effects of dry-wet cycles on compacted loess: from macroscopic to microscopic investigation	5
Optimization of dune sand-based mixture material for pavement design	5
Experimental study on fracture properties of concrete under cyclic loading using digital image correlation method	5
Machine foundation response subjected to vertical vibration: experimental and analytical using cone model	5
Effect of rice husk ash as partial replacement of ordinary Portland cement in ultra-high-performance glass concrete	5
Experimental investigation of linear damping characteristics on granite and red sandstone under dynamic cyclic loading	5
Influence of alkali activators on thermo-physical properties of ecofriendly unfired clay bricks from anthill mounds	5
Effect of glass powder on the rheological and mechanical properties of slag-based mechanochemical activation geopolymer grout	5
Performance of recycled concrete aggregates based self-compacting concrete containing coal combustion ashes and silica fume	5
Experimental and numerical investigation of strengthening of openings in masonry walls using steel bars and steel wire mesh	5
Effect of graphene oxide and functionalized carbon nanotubes on mechanical and durability properties of high volume fly-ash cement nanocomposite	5
Experimental and analytical investigations on the failure modes of concrete sandwich panels under axial compression	5
Load-sharing mechanism of piled-raft foundation: a numerical study	5
Durability of recycled waste plastic aggregate concrete	5
Numerical study on full-field stress evolution and acoustic emission characteristics of rocks containing three parallel pre-existing flaws under uniaxial compression	5
Properties of geopolymer mortars derived from ground calcined perlite and NaOH solution	5
One-dimensional large-strain model for soft soil consolidation induced by vacuum-assisted prefabricated horizontal drain	5
Dynamic behaviour of drystone retaining walls: shaking table scaled-down tests	5
A dynamic Gaussian process surrogate model-assisted particle swarm optimisation algorithm for expensive structural optimisation problems	5
Influence of low fines content on the liquefaction resistance of sands	5
Influence of stress relief due to deep excavation on a brick masonry wall: 3D numerical predictions	5
Enhancing the internal curing process of self-compacting concrete containing lightweight aggregate and chemical additives	4
Investigation of the effect of commercial limestone on alkali-activated blends based on Algerian slag-glass powder	4
Exploration of the mechanical properties, durability and application of geopolymers: a review	4
A novel extreme gradient boosting algorithm based model for predicting the scour risk around bridge piers: application to French railway bridges	4
Investigation on rapid solidification of waste dredged sludge with magnesium phosphate cement modified by GGBFS	4
Engineering behavior of ambient-cured geopolymer concrete activated by an alternative silicate from rice husk ash	4
3D DEM investigation of the resistance of ice and frozen granular soils	4
Corrosion-resistance evaluation of coated and specialty bars	4
Simulation of internal and external sulfate attacks of concrete with a generic reactive transport-poromechanical model	4
Real-time implication of hybrid carbonaceous fibre and powder integrated self-sensing cement composite in health monitoring of beams and columns	4
The behavior of strengthened and repaired RC columns with (CFRP) rope under different preloading levels	4
The compressive and tensile behavior of polypropylene fibers and activated fly ash incorporated concrete at elevated temperatures	4
A thermal–hydromechanical coupled model for poro-viscoplastic saturated freezing soil	4
On CO2 sequestration in concrete aggregate via carbonation: simulation and experimental verification	4
Characteristics of unconfined masonry walls under in-plane static and reverse-cyclic loading: a comparative numerical study	4
Seismic performance of semi-precast high-strength recycled concrete columns with ultra-high-strength steel bar	4
Improving the mechanical properties of recycled aggregate concrete with graphene	4
A log-spiral limit equilibrium analysis for passive earth pressure under the effect of unsaturated seepage conditions	4
Analysis of mechanism, properties and existing problems of liquid setting accelerators	4
Flow exchange and unsaturated permeability of cracked clay: experimental and modelling	4
Liquefaction resistance behaviours of gravel steel slag	4
Mechanical behaviour of rock containing a persistent joint under uniaxial compression at different strain rates	4
Influence of GGBFS and silica fume on characteristics of alkali-activated Metakaolin-based concrete	4
Experimental study on internal erosion and seepage in the foundation of a dike under variable water head	4
Coupling hardening soil model and Ménard pressuremeter tests to predict pile behavior	4
Study on calcareous sand treated by MICP in different NaCl concentrations	4
A study of the rheological behaviour of eco-friendly mortar made with metakaolin and marble powder at various ambient temperatures	4

Optimum characteristics of plastic fibres for sustainable self-compacting concrete SCC	4
Crack propagation studies in strain hardened concrete using acoustic emission and digital image correlation investigations	4
Numerical modelling of desiccation shrinkage and cracking of soils	4
Influence of styrene-butadiene rubber and pretreated hemp fibers on the properties of cement-based repair mortars	4
Numerical study of dynamic fracture behaviors of rock containing double pre-existing flaws under different confined stress and flaw geometry	3
Seismic characteristics of isolated plate-shell integrated concrete LSS	3
Study on strong contact system by sub-network partitioning method for binary mixtures	3
High temperature effects on the properties of a high porosity calcareous stone building material	3
Development of sustainable self-compacting concrete utilising silico manganese fume	3
Stability assessment of soil-nailed slopes using the homogenisation approach	3
Experimental study of flexural behaviour of RC beams strengthened using near surface mounted CFRP strips and ropes	3
Investigations on fracture related properties of strain hardened concrete using digital image correlation and acoustic emission techniques	3
Mechanical and microstructural properties of silt roadbed filling improved with cement, red mud and desulfurization gypsum	3
Scouring effects on lateral cyclic responses of piles in sand	3
Performance of chemical substance inhibitors on the surface between steel rebar and concrete	3
Hybrid finite–discrete element modelling of rock fracture process in intact and notched Brazilian disc tests	3
Deep residual network training for reinforced concrete defects intelligent classifier	3
Prediction of shear strength of RC deep beams using XGBoost regression with Bayesian optimization	3
‘Efficacy of sodium alginate, xanthan gum, and diatomite admixtures in improving the strength and shrinkage behaviour of EPS lightweight concrete’	3
A comparison index in mortar repair treatments by microbiologically induced carbonate precipitation and its evaluation by a non-destructive technique	3
Seismic performance evaluation of retrofitted RC beam-column joints reinforced by plain and deformed bars	3
Hydration characteristics and microstructure evolution of concrete with blended binders from LCD and OLED wastes	3
Preliminary study on the fresh and mechanical properties of UHPC made with recycled UHPC aggregates	3
Valorization of uncontaminated dredged marine sediment through sand substitution in marine grade concrete	3
A systematic review on MICP technique for developing sustainability in concrete	3
Limits of enhanced of macro- and meso-scale continuum models for studying size effect in concrete under tension	3
Experimental study on the shear mechanical behaviour of rock-like materials containing one embedded flaw under unloading normal stress conditions	3
Mechanical, physicochemical, microstructural and self-cleaning performance of nano-titanium dioxide containing photocatalytic cement mortars exposed to elevated temperatures	3
Investigation of torsion in confined masonry structures originating due to unsymmetric openings	3
A binary-medium-based constitutive model for artificially cemented gravel-silty clay mixed soils	3
Step-changed strain rate effect on the mechanical properties of undisturbed expansive clay	3
Durability characteristics and mechanical properties of multi-walled carbon nanotubes reinforced concrete, a case study: Caspian seawater curing condition	3
Water vapor permeability of flax fibers reinforced raw earth: Experimental and micro-macro modeling	3
Plastic shrinkage cracking properties of high-performance shotcrete with supplementary cementitious materials	3
Experimental feasibility for the incorporation of solid waste aggregates in masonry hollow blocks	3
Mechanical, sound and thermal properties of recycled expanded polystyrene concrete reinforced with 0.5% to 5.5% kenaf fibre	3
Strength, life cycle analysis, embodied energy and cost-sensitivity assessment of sugarcane bagasse ash-based ternary blends of geopolymer concrete	3
Hydration of flax fibre-reinforced cementitious composites: influence of fibre surface treatments	3
Creep model for the long-term behaviour of combined cohesive-bridging model of FRP–concrete interface debonding under axial loading	3
Stability of rectangular tunnel in anisotropic cohesionless soil under steady-state groundwater flow	3
Experimental study and particle flow modeling on 3D cracking behavior of rock-like samples with an embedded flaw	3
Combined effect of using steel fibers and demolition waste aggregates on the performance of fly ash/slag based geopolymer concrete	3
A comprehensive investigation on bearing capacity of shallow foundations on unsaturated fly ash slopes adopting finite element limit analysis	3
Dispersion, viscosity, unconfined compression and bender element testing of bentonite-waste glass mixtures	3
Microstructure and chemo-physical characterizations, thermal properties, and modeling of the compression stress-strain behavior of lime-based roof and screed paste	3
Experimental behaviour of unreinforced and confined rat-trap bond masonry	3
Instability analysis of jointed rock slope subject to rainfall using DEM strength reduction technique	3
Effect of 10% recycled sands from various storage sites on the mortar’s properties	3
A practical model for moment redistribution in statically indeterminate RC beams	3
Development of a maturity method for GFRC shell concretes with different fiber ratios	3
Shear strengthening of brick masonry walls with opening	3
Strut-and-tie model for FRP effectiveness in shear strengthening of RC deep beams	3
Learning simple additive weighting parameters for subsidence vulnerability indices in Tehran plain (Iran) by artificial intelligence methods	3
Experimental characterization of desiccation cracking mechanisms in clayey soils	3
Behavior of repaired projectile bullet damaged reinforced concrete beams using CFRP sheet in conjunction with natural aggregate or recycled aggregate concrete layer	3
Probabilistic evaluation of chloride-induced corrosion effects on design parameters of RC beams	3
Prediction of limit support pressure for face stability of deep tunnels buried beneath sea/water	3
Compressive behavior and microstructural analysis of low and high volume fly ash concrete containing recycled concrete aggregate	3
An eco-friendly reliability-based design optimization of intermediate reinforced concrete moment frames	3
Very high early strength calcium aluminate based binary and ternary cementitious systems: properties, hydration and microstructure	3
Seismic energy dissipation in reinforced concrete beam: investigating damping formulations	3
Effect of wetting stress paths on mechanical behavior and instability of unsaturated soil in stress state space	3
A novel damage index for reinforced concrete beam-column joint using acoustic emission technique	3
Probabilistic analysis of the crack spacing in reinforced concrete members under tensile loads – numerical investigation of size effects	3
Influence of geometrical uncertainties of analytical modelling on the evaluation of building deflections induced by ground movements	2
Evaluation of the soil layering and soil lens effect on the ground-borne vibrations induced by twin metro tunnels	2
Experimental investigation on the desiccation cracking process in date palm fiber reinforced clayey soil using digital image correlation	2
Stiffness and strength parameters for the hardening soil model of a reconstituted diatomaceous soil	2
Experimental analysis on tensile and bond properties of basalt-ettringite TRM for strengthening masonry structures	2
Test results for a monopile in medium dense sand subjected to unidirectional lateral cyclic loading	2
An experimental investigation on the dovetail notched connection for cross-laminated-timber-concrete composite slabs	2
Experimental study on vegetation performance improvement of carbonaceous mudstone aggregate vegetation concrete with its micromechanism	2
Physical modelling of EPB TBM in dry sand and greenfield conditions	2
Simulation of steam/air leakage through small-scale cracked concrete specimen	2
Experimental investigation on shear behaviours of textile reinforced concrete beams	2
On the hydraulics of flow in cracks in embankment dam cores	2
Dynamic analysis of rock fall impact for a cantilever rock shed with geofoam cushion	2
Waste coal cement concrete for sustainable production	2
Analytical solutions for one-dimensional nonlinear large strain consolidation of soft soils with high compressibility under a multi-stage loading	2
Valorization of powder of volcanic rocks used as cement substitution in self-compacting concrete	2
Effect of transient drying on mechanical properties of concrete specimens	2
Experimental study on the relationship between local deformation and macro-crack evolution of granite under conventional triaxial compression	2
An experimental and analytical research on moment redistribution in reinforced concrete continuous beams	2
Strength and durability properties of recycled aggregate concrete blended with hydrated lime and brick powder	2
Numerical and statistical investigation of the performance of closed-cell aluminium foam as a seismic isolation layer for tunnel linings	2
Effect of fly ash and red mud on strength and electrochemical properties of seawater mixed concrete	2
Engineering statistical models for carbonation depth	2
Analyzing the effectiveness of anti-slide piles for slope stabilization against seismic loading using discrete element method	2
Surface application of multifunctional compound to prevent and control combined chloride and carbonation corrosion in concrete	2
Performance evaluation of sustainable recycled aggregate concrete with colloidal nano-silica	2
A DEM-based approach for modeling the thermal-mechanical behavior of frozen soil	2
Fragility of single-span masonry arch bridges accounting for deterioration and damage effects	2
Timber connection behaviour characterisation based on similitude laws	2
Study on the workability, mechanical properties of fish tail palm fibre reinforced concrete-emphasis on fibre content and fibre length	2
Developing a multi-variable vulnerability function for a class of multi-span continuous concrete box-girder highway bridges with emphasis on near-field earthquakes	2