OOIR: Observatory of International Research

Papers

(The median citation count of Archives of Civil and Mechanical Engineering is 4. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-11-01 to 2024-11-01.)

Article	Citations
Tunnel deformation and stress response under the bilateral foundation pit construction: a case study	52
Isogeometric couple stress continuum-based linear and nonlinear flexural responses of functionally graded composite microplates with variable thickness	47
Isogeometric nonlinear bending analysis of porous FG composite microplates with a central cutout modeled by the couple stress continuum quasi-3D plate theory	47
Statistical damage constitutive model based on the Hoek–Brown criterion	40
Microstructure evolution and property analysis of commercial pure Al alloy processed by radial-shear rolling	21
Effect of multi-walled carbon nanotubes on the damping property of cement mortar and mechanism analysis	21
Creep, shrinkage and permeation characteristics of geopolymer aggregate concrete: long-term performance	21
Generalized thermoelasticity model of nonlocal strain gradient Timoshenko nanobeams	19
Analytical modeling of surface generation in ultrasonic ball burnishing including effects of indentation pile-up/sink-in and chipping fracture	17
Fracture limit analysis of DP590 steel using single point incremental forming: experimental approach, theoretical modeling and microstructural evolution	16
Effects of equal channel angular pressing and heat treatments on the microstructures and mechanical properties of selective laser melted and cast AlSi10Mg alloys	15
Silicon carbide nanocomposites reinforced with disordered graphitic carbon formed in situ through oxidation of Ti3C2 MXene during sintering	14
Effect of rubber particles on impact resistance of concrete at a temperature of − 20 ℃	14
Nonlinear resonance and chaotic dynamic of rotating graphene platelets reinforced metal foams plates in thermal environment	13
Fatigue failure analysis of three-layer Zr–Ti/Zr–Steel composite plates: an insight into the evolution of cracks initiated at the interfaces	12
Detailed micro-modeling of partially grouted reinforced masonry shear walls: extended validation and parametric study	12
Numerical simulation for train–track–bridge dynamic interaction considering damage constitutive relation of concrete tracks	11
Surface properties enhancement of Inconel 718 alloy by ultrasonic roller burnishing coupled with heat treatment	11
Investigation of modified friction stir clinching-brazing process of AA2024 Al/AZ31 Mg: metallurgical and mechanical properties	11
Mechanical and thermal stability of retained austenite in plastically deformed bainite-based TRIP-aided medium-Mn steels	11
Influence of curing conditions on the mechanical performance of ultra-high-performance strain-hardening cementitious composites	11
Microstructure and mechanical properties of TC4 titanium alloy hollow shaft formed by cross wedge rolling	10
Multi-objective optimization of process parameters in cold forging minimizing risk of crack and forging energy	10
Performance study of precast reinforced concrete shear walls with steel columns containing friction-bearing devices	9
A physically based constitutive model of Ti-6Al-4 V and application in the SPF/DB process for a pyramid lattice sandwich panel	9

Processing of commercially pure copper tubes by hydrostatic tube cyclic extrusion–compression (HTCEC) as a new SPD method	9
Crashworthiness-based multi-objective integrated optimization of electric vehicle chassis frame	9
Tribological performance of gas tungsten arc welded dissimilar joint of sDSS 2507/IN-625 for marine application	9
Prestress state evolution during thermal activation of memory effect in concrete beams strengthened with external SMA wires	9
Providing a new perspective for obtaining high-quality metal coatings: fabrication and properties studies of TA2 foil on Q235 steel by explosive welding	8
Prediction of forming limits and microstructural evolution during warm stretch forming of DP590 steel	8
Effect of air entraining and pumice on properties of ultra-high performance lightweight concrete	8
The effect of freeze–thaw cycles on flexural behaviour of FRP-reinforced ECC beams	8
Synergistic effects of alloying, homogenization, and hot extrusion on the mechanical properties of as-cast Mg–Al–Ca magnesium alloys	7
Experimental and numerical investigation on plasticity and fracture behaviors of aluminum alloy 6061-T6 extrusions	7
Quantitative Rietveld analysis of the decomposition of hardened rapid sulphoaluminate cement after exposure to elevated temperatures	7
Assessment of modal characteristics of cross-laminated timber beams subject to successive damages	7
Effects of manufacturing methods and production routes on residual stresses of rectangular and square hollow steel sections: a review	7
Fracture behavior of 7075-T6 aluminum alloy under electromagnetic forming and traditional stamping	7
Rehabilitation of RC flexural members in shear with externally bonded fiber-reinforced polymer composites: present status and future need	6
Analysis of vane loads and motion in a hydraulic double vane pump with integrated electrical drive	6
Dynamic non-linear Mohr–Coulomb strength criterion for hybrid basalt–polypropylene fibre-reinforced concrete under impact loading	6
Exhaust system piping made by hydroforming: relations between stresses, microstructure, mechanical properties and surface	6
Deformation and failure mechanism of deep cement mixing walls: experimental study using physical model tests	5
Experimental investigation and analysis on the axial compressive performance of recycled concrete-filled corroded steel tubular columns	5
Electro-magneto-mechanical formulation of a sandwich shell subjected to electro-magneto-mechanical considering thickness stretching	5
The decisive impact of microstructure on the machinability of pure copper	5
Microstructural and mechanical properties of CFC composite/Ti6Al4V joints brazed with Ag–Cu–Ti and refractory metal foils	5
Solid-state welding of ultrafine grained copper rods	5
Analysis of thickness variation and stress state in hydroforming of complex T-shaped tubular part of nickel-based superalloy	5
A multiscale experimental analysis of mechanical properties and deformation behavior of sintered copper–silicon carbide composites enhanced by high-pressure torsion	5
Experimental study of nanocomposite hybrid adhesive-rivet joints	5
Physical simulation and dilatometric study of double-step heat treatment of medium-Mn steel	5
Seismic behavior and damage assessment of mid-rise cold-formed steel-framed buildings with normal and reinforced beam-column joints	5
Work hardening of Ni-based single crystal alloy in vibration grinding based on molecular dynamics method	4
Fabrication and effect of Mg–Zn solid solution via Zn foil interlayer alloying in FSW process of magnesium alloy	4
Three-dimensional exact elastic analysis of nanoplates	4
Structural assessment of bridges through ambient noise deconvolution interferometry: application to the lateral dynamic behaviour of a RC multi-span viaduct	4
Structural performance of reinforced concrete interior beam–column joints with high-strength bars	4
Shear behaviour of I-shaped steel with bamboo scrimber composite beams	4
Numerical and experimental study on the inner diameter uniformity of hollow shafts in cross-wedge rolling with mandrel	4