OOIR: Observatory of International Research

Papers

(The median citation count of Multidiscipline Modeling in Materials and Structures is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-03-01 to 2025-03-01.)

Article	Citations
Capacity prediction of straight and inclined slender concrete-filled double-skin tubular columns	31
Description of crystal defect properties in BCC Cr with extended Finnis–Sinclair potential	29
Machinability optimization of carbon fiber reinforced polymer composites for aviation manufacturing parts	27
Implementation of improved Fourier's law and Fick's law for rotational flow of nanofluid over an exponentially stretching sheet	26
Site effect influence on the seismic vulnerability of unreinforced masonry buildings in low to moderate seismic urban areas in Algeria	22
2D problem of nonlocal rotating thermoelastic half-space with memory-dependent derivative	16
Effects of non-symmetric non-uniformly distributed welding residual stress on fatigue failure initiation and propagation in a hydropower generator shaft	16
Statistical and experimental study on microcrack of mortar by a self-healing agent of bacteria adsorbed by expanded perlite	15
Viscous fluid flow and heat transfer past a permeable wall jet with convective boundary conditions	14
An innovative reinforcement method: the combination of CFRP bars and UHPC layer is applied to the flexural reinforcement of RC beams	14
Modeling of voltage-limiting kinetics in two-layer varistor–posistor structures	14
Simulation of coupled elasticity problem with pressure equation: hydroelastic equation	13
Review of research progress and development trend of digital image correlation	12
Investigation on effect of carbon equivalent and inoculation on the solidification and shrinkage tendency of ductile cast iron using thermal analysis	11
Entropic behavior with activation energy in the dynamics of hyperbolic-tangent mixed-convective nanomaterial due to a vertical slendering surface	11
Entropic behavior in bidirectional flow of CeO₂-ZnO/water hybrid nanofluid with prescribed surface temperature/heat flux aspects	10
Multicriteria decision-making for optimization of welding parameters in cold metal transfer and pulse metal-inert gas weld bead of AA2099-T86 alloy using CRITIC and ROV methods	10
A novel model on nonlocal thermoelastic rotating porous medium with memory-dependent derivative	10
Dynamic characteristics analysis of complex aircraft pipeline system using MDSMA algorithm	8
Rheological model of cement-based material slurry with different water-cement ratio and temperature	8
Boundary layer analysis on magnetohydrodynamic dissipative Williamson nanofluid past over an exponentially stretched porous sheet by engaging OHAM	8
On stress concentration analysis of inverse distance weighted function based finite FGM panel with circular hole under biaxial loading	8
Numerical investigation of magnetized bioconvection and heat transfer in a cross-ternary hybrid nanofluid over a stretching cylinder	8
A comprehensive study on using expanded silica gel size as hollow sphere material in different aluminum alloy-based syntactic foams	7
Breaking process of composite membranes used in desalination phenomenon	7

Robust optimization of EMU brake module based on interval analysis	7
Wavy mathematical modeling of dynamically reactive shear thinning materials under the influence of gravity and wavy structures amplitude	6
Thermal transport analysis for entropy generated flow of hybrid nanomaterial: modified Cattaneo–Christov heat and Darcy–Forchheimer	6
Fracture mechanism and failure criterion of S-07 steel for liquid rocket engine	5
Time-dependent flow of Reiner–Rivlin nanofluid over a stretching sheet with Arrhenius activation energy and binary chemical reaction	5
Study on the effects of guide fins structures on the flow and thermal uniformity of the motorcycle exhaust thermoelectric generator	5
Parameter-free strain-energy function which automatically and accurately matches benchmark test data for soft elastic solids	5
Investigation of Sutterby fluid flow through elliptic multi-stenosed artery: analytical solutions of blood flow problem	5
Wire EDM cutting of Inconel 718 nickel-based superalloy: kerf and MRR analysis	5
Modeling and analysis of TiO₂ filler's impact on specific wear rate in flax fiber-reinforced epoxy composite under abrasive wear using Taguchi approach	5
Front propagation in the interaction of gases to model a fuel tank inerting process with a nonlinear parabolic operator	5
Love-type wave characteristics in the heterogeneous hydrogel layer pasted over the functionally graded piezoelectric fiber-reinforced composites semi-infinite substrate	5
Steady state creep of the silver-tin TLP interconnections of power modules	5
Modeling mechanical behavior of distributed piezoelectric actuators for morphing wing applications	4
Effect of freeze-thaw damage at curing time on mechanical properties of polyurethane concrete	4
The effect of manufacturing defects on the high-cycle fatigue of electron-beam-welded Ti-6Al-4V titanium alloy: experimental and numerical analysis	4
Optimizing surface roughness in soft pneumatic gripper fabricated via FDM: experimental investigation using Taguchi method	4
Numerical study on influence of inclination and sinusoidal heating on magneto-convection in an inclined lid-driven cavity	4
The integrated MHD thermal performance with slip conditions on metachronal propulsion: the engineering material for biomedical applications	4
Investigation on structural integrity of shape distorted 90° back-to-back pipe bends under in-plane closing bending moment	4
Modeling of resettable fuses characteristics for protection of solar arrays from current overloads	3
Study of the dynamic response of a CAARC building by the synthetic wind method and comparison with different approaches	3
The solutions of dissipation-dispersive models arising in material science	3
Hydro-thermo-fluidic aspects of Oldroyd B fluid with hybrid nanostructure subject to low and moderate Prandtl numbers	3
Microstructural, microhardness and electrical conductivity analysis of AD31T alloy processed by friction stir processing	3
Multiphysics simulations of uniaxial compression applied to various rock samples subject to microwave pretreatment	3
Efficient aerodynamic optimization of turbine blade profiles: an integrated approach with novel HDSPSO algorithm	3
Evolution and comprehensive evaluation of viscoelastic characteristics of road asphalt in medium temperature region	3
Prediction of load requirement and instabilities during end forming of friction stir processed AA 6063-T6 thin-walled tubes	3
Global sensitivity analysis of structural models by active subspace and neural network	3
Finite coating thickness of Prandtl fluid in non-isothermal reverse roll coating process	3
Aircraft joint structure lightweight design	3
Predicting hot wire tungsten inert gas welding parameters for joining P91 and 304HCu steel using multi-optimization techniques	3
Supervised machine learning techniques for optimization of heat transfer rate of Cu-H₂O nanofluid flow over a radial porous fin	3
Numerical characterizations of the thermomechanical response of power modules with ceramic substrates and lead-free bonds	3
Rayleigh-type surface waves in a thermally conducting mixture of an elastic solid and a Newtonian fluid	3
Crystal structure optimization approach to problem solving in mechanical engineering design	3
The effect of the properties of La_xNd_8‒xB₆ (x = 1,2,6)	3
Polymer presence in boundary layer flow and heat transfer of dusty fluid over a stretching surface	3
Analytical and inverse method for determining high temperature properties of materials using small punch creep: a review	3
CuMg₂GaS₄: a novel photocatalyst with promising properties	3
Optimization of structural parameters for the sound absorption performance of a cellular ceramic foam	3
Relative frugal wavelet transform to detect damages in functionally graded tapered beams made of porous material	2
Analytical modeling and optimal design of clamped sandwich beams with cellular cores subjected to shock loading	2
Calculation of energy and magnetic susceptibility of Fe atomic system during dislocation motion in magnetic field	2
3D printing of asymmetric buttress plate for posteromedial tibial plateau fracture using metal fused filament fabrication	2
Thermoelastic micro-stretch solid immersed in an infinite inviscid fluid and subject to gravity under three-phase-lag model	2
Drop cushioning dynamic effects of corrugated cardboard with effective anisotropic constitutive model	2
Flow analysis of water conveying nanomaterials over a rotating surface with thermal radiation	2
Influence of initial stress and gravity on fiber-reinforced thermoelastic solid using Moore–Gibson–Thompson generalized theory of thermoelasticity	2

Computational homogenization based crystal plasticity investigation of deformation behavior of AA2024-T3 alloy at different strain rates	2
Assessment of the effect of straw lignin-based synthetic resin as a modifier on the rheological properties of asphalt binder towards better utilization of straw biomass	2
Thermal management of square light emitting diode arrays: modeling and parametric analysis	2
Multi-performance optimization for AWJ drilling process in cutting of ceramic tile: BBD with EOBL-GOA algorithm	2
Special review: Mechanical investigation on failure modes of reticular porous metal foams under different loadings in engineering applications	2
Vibration response analysis of a two-stage vibration isolation system for large airborne equipment	2
Physical manufacturing: from the multidisciplinary perspective	2
Study of nanofiltration membrane process by Langevin dynamic model	2
Evaluation method of equivalent initial flaw size and fatigue life prediction of nickel-based single crystal superalloy	2
The numerical study of CLT shear walls with low-yield steel dampers	2
Numerical study of the volume fraction and thermophysical properties of nanofluids in a porous medium	2
Numerical investigation on the premature and extended contact behaviour of engineering thermoplastic gears and its effect in gear kinematics	2
A new simple method to conveniently measure the open porosity of porous metal foams with reticular structure	2
Simulation of reinforced concrete beam retrofitted with steel angles subjected to flexure	2
High-temperature oxidation and gas thermal shock studies of IC10 simulated specimens with thermal barrier coatings	2
Boundary layers at the interface of thermally radiative nanofluid and Ree–Eyring fluid with different shear strength	2
Influence of width-to-depth and effective length-to-depth ratio on shear strength of reinforced concrete slender beams without shear reinforcement: comparative analysis	2
An analysis on the effect of layer number on the stability of thin DNA origami nanopores	2
Research on structural performance evolution of clay based on distribution force model	2
Evaluating the accuracy and effectiveness of machine learning methods for rapidly determining the safety factor of road embankments	2
A mathematical model for erosive abrasive wear analysis by using abrasive size and material hardness	2
Numerical exploration of bioconvection in optimizing nanofluid flow through heated stretched cylinder in existence of magnetic field	1
Effect of fin density and fin height on flow-induced vibration behavior of finned tube arrays subjected to water cross flow	1
A novel technique to analyze the fractional model of Williamson and Casson non-Newtonian boundary layer flow	1
Numerical study of hybrid nanofluid and thermal transport in sun-powered energy ship within the application of parabolic trough solar collectors	1
Study on the impact of ultrasonic vibration-assisted grinding of glass-ceramics on surface/subsurface damage mechanism	1
Impact of balcony geometry on the performance of rubberized concrete structures against progressive collapse	1
Feature-rich electronic properties of three-dimensional ternary compound: Li₇P₃S₁₁	1
Machine learning applications to predict the axial compression capacity of concrete filled steel tubular columns: a systematic review	1
Rock–bit interaction effects on high-frequency stick-slip vibration severity in rotary drilling systems	1
A modified model for ultimate bearing capacity of CFRP-shear-strengthened pre-cracked beams with geopolymer	1
Comparison of flexural capacity of different hollow slab beams with/without pavement layer reinforced by steel plates	1
Impact of porosity on free vibration and limit analysis of power-law-based functionally graded disks	1
Reliability analysis of time-dependent problems based on ensemble learning of surrogate models	1
Heat transfer analysis of thermal radiative over a stretching curved surface using molybdenum disulfide and silicon dioxide composite material under the influence of solar radiation	1
The research of buckling and post-buckling behavior of bidirectional stiffened composite panel under discrete impact	1
Experimental and finite element analyses on the vibration behavior of 3D-printed PET-G tapered beams with fused filament fabrication	1
Limit angular speed analysis of porous functionally graded rotating disk under thermo-mechanical loading	1
Synthesis of an efficient phosphorus and triazine ring-containing reactive flame retardant for epoxy resin	1
Nonlocal thermodynamical vibrations in a rotating magneto-thermoelastic medium based on modified Ohm's law with temperature-dependent properties	1
Space time fractional Ito system with variable coefficients: explicit solution, conservation laws and numerical approximation	1
Thermophoretic particle deposition and double-diffusive mixed convection flow in non-Newtonian hybrid nanofluids past a vertical deformable sheet	1
Hygrothermal analysis of a semi-infinite cylinder: an integral transform approach	1
An innovative reliability-based design optimization method by combination of dual-stage adaptive kriging and genetic algorithm	1
Free vibration analysis of functionally graded rectangular plates under asymmetric boundary conditions using coupled displacement field method	1
Modeling of the machining parameters in turning of Al-5052/TiC/SiC composites: a statistical modeling approach using grey relational analysis (GRA) and response surface methodology (RSM)	1
Multiple solutions for gravity-driven thermally heated material of dissipative Ohmic hybrid nanofluids	1
Novel solitary wave solution of the nonlinear fractal Schrödinger equation and its fractal variational principle	1
Mechanical properties of PLA based closed porous structures manufactured using FDM process	1
Second order slip flow of a conducting Jeffrey nanofluid in an inclined asymmetric porous conduit with heat and mass transfer	1
The effect of memory and stiffness on energy ratios at the interface of distinct media	1
Convective heat transfer analysis for magnetohydrodynamics Reiner–Philippoff nanofluid flow over a curved stretching surface: non-similar solution	1
Simulation studies on combined effect of variable geometry, rotation and temperature gradient on critical speed of gas turbine disc	1
Numerical assessment of viscoelastic tetra hybrid nanofluid flow across a stretchable rotatory disk under the Soret and Dufour aspects	1
The physical mechanism of heat transfer enhancement for Al₂O₃-water nanofluid forced flow in a microchannel with two-phase lattice Boltzmann method	1
Heat transfer analysis in a horizontal anisotropic porous channel with Bi-viscous Bingham nanofluid and temperature-dependent Brownian diffusion	1
Reliability analysis of various modeling techniques for the prediction of axial strain of FRP-confined concrete	1
Propagation of plane waves at the initially stressed surface of an orthotropic nonlocal rotating half space under dual-phase-lag model	1
An investigation on the cyclic deformation and service life of a reusable liquid rocket engine thrust chamber wall	1
Size-dependent vibration analysis of the simply supported functionally graded porous material Al-Al₂O₃ rectangle microplates based on the modified couple stress theory with innov	1
Quantitative analysis of the electromagnetic hybrid nanofluid flow within the gap of two tubes using deep learning neural networks	1
Phase-field simulations of isomorphous binary alloys subject to isothermal and directional solidification	1
Computational outline on heat transfer analysis and entropy generation in hydromagnetic squeezing slip flow of hybrid nanofluid	1
Experimental investigation and numerical simulation of the flexural behavior of reinforced concrete beams strengthened by geopolymer-bonded CFRP	1
Hybrid ferrofluid flow on a stretching sheet with Stefan blowing and magnetic polarization effects in a porous medium	1
Magnetohydrodynamic hybrid nanofluid flow over a decelerating rotating disk with Soret and Dufour effects	1
Effect of high-frequency PCB laminate on thermal cycling behavior of electronic packaging structures	1