OOIR: Observatory of International Research

Papers

(The H4-Index of Journal of Manufacturing Processes is 68. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)

Article	Citations
Editorial Board	431
Editorial Board	307
On the brink of mass production and simultaneous multi-component surface modifications for ultra-fast polishing: Plasma electrolytic polishing process	271
Multi-material additive manufacturing of aluminum 6061-T6 alloy with stainless steel 304: Suppression of intermetallic compounds and interface growth mechanism	251
Grinding performance and parameter optimization of laser DED TiC reinforced Ni-based composite coatings	247
Toward closed-loop quality assurance in powder bed fusion additive manufacturing: Defect detection, machine learning, and computational modeling	222
Effect of in-situ layer scanning ultrasonic vibration on mechanical and morphological properties of fused deposition modeled poly(lactic) acid specimens	197
Weld formation, arc behavior, and droplet transfer in narrow-gap laser-arc hybrid welding of titanium alloy	181
Effects of laser scanning speed on the microstructure and mechanical properties of 2205 duplex stainless steel fabricated by selective laser melting	157
An investigation of monitoring the damage mechanism in ultra-precision grinding of monocrystalline silicon based on AE signals processing	149
Achieving superior tribological resistance of Ti-6Al-4 V alloy via femtosecond laser shock peening	148
Feasibility study on sensing and prediction of backside weld geometry in cold metal transfer welding of X65 pipeline in the vertical-up position	143
Robust thermal error estimation for machine tools based on in-process multi-point temperature measurement of a single axis actuated by a ball screw feed drive system	137
An unsupervised welding quality detection method based on high-quality condition-guided diffusion reconstruction	127
Design intent-preserving non-rigid toolpath morphing: A novel skeleton-skin method for undercut compensation and rapid numerical control programming of near-net-shape parts	125
Development of Extractor-Classifier-Regulator integrated anomaly detection model for turning process	124
Asymmetry in microstructure and mechanical properties of FSWed joints using a hemispherical tool tilted towards the retreating side	120
Mechanistic analysis and optimization methods of post-cutting lateral camber formation in hot-rolled strips	120
A unified framework based on semantic segmentation for extraction of weld seam profiles with typical joints	115
Efficient end milling of curved thin-walled workpieces using a composite magnetic follow-up flexible fixture	111
Phenomenological modeling for femtosecond laser processing of fused silica	105
Modeling of cold pilgering of stainless-steel tubes	105
Rheological formulation of room temperature vulcanizing silicone elastomer ink for extrusion-based 3D printing at room temperature	105
An imbalanced small sample slab defect recognition method based on image generation	101
The effect of build orientation on tensile properties and corrosion resistance of 316L stainless steel fabricated by laser powder bed fusion	99

Study on sustainable milling performance of aluminum alloys with application of blended plant oil-based composite electrostatic spray lubrication	99
Delayed fracture stress thresholds degraded by the shear punching process in ultra-high-strength steel sheets: Analysis using an in-plane bending test with numerical assimilation	99
Modelling the keyhole profile in laser welding through energy balance including the local contribution of multiple reflections through the plasma by ray tracing	99
Reprint of: Physical modeling for digital twin of Continuous Damping Control damper	98
Directional enhancement of wettability for Al/stainless-steel system: Exploring the potential of laser-chemical hybrid surface texturing	97
Compressive residual stresses in LTT elongated bead welded in all positions for fatigue crack prevention of boxing fillet joints	96
Optimisation of a novel hot air contactless single incremental point forming of polymers	95
Study on the nano-cutting mechanism of monocrystalline silicon material with an amorphous layer by molecular dynamics simulations	95
Additive manufacturing multi-material components of SAF 2507 duplex steel and 15-5 PH martensitic stainless steel	94
Fatigue strength improvement of linear friction welded butt joints of low carbon steel by pressurizing after oscillation	93
Investigate on material removal of 3C-SiC crystals in nano-polishing via molecular dynamics	91
Ultrasonic system and ultrasonic metal welding performance: A status review	90
A critical review on advanced welding technologies to fabricate test blanket modules and irradiation damage behaviour of the welded joints in nuclear fusion applications	90
A new cross-domain bearing fault diagnosis method with few samples under different working conditions	88
An analytical force model in sawing brittle and heterogeneous material considering the interactions of grit-granite	86
Defining the printing direction impact of additively manufactured sand molds on casting roughness	83
Effect of scanning spacing on the efficiency of CFRP hole-cutting with multi-pass scanning strategy by nanosecond laser	83
Material deformation mechanism of polycrystalline tin in nanometric cutting	80
Numerical simulation of weld formation in friction stir welding based on non-uniform tool-workpiece interaction: An effect of tool pin size	79
Improving bending and interlayer properties of hybrid-fiber-reinforced composites through functionally graded hybrid strategy by 3D-printing manufacturing process	79
Development, challenges and future trends on the fabrication of micro-textured surfaces using milling technology	79
Microwave joining of SS-316 plates: A multi-physics simulation study	78
Dual flexible contact material removal model for robotic disk grinding	77
Trajectory planning method with grinding compensation strategy for robotic propeller blade sharpening application	76
Effect of ultrasonic vibration on the machining performance and mechanism of hybrid ultrasonic vibration/plasma oxidation assisted grinding	75
Revolutionizing manufacturing: A comprehensive overview of additive manufacturing processes, materials, developments, and challenges	75
Possibilities, performance and challenges of nitinol alloy fabricated by Directed Energy Deposition and Powder Bed Fusion for biomedical implants	75
Experimental investigations on thermo-stamping of carbon fiber reinforced polyamide 6 hat-shaped components with self-resistance electrical heating: Influence on microscopic and macroscopic properties	74
Influence of tool vibration and cutting speeds on removal mechanism of SiCp/Al composites during ultrasonic elliptical vibration-assisted turning	73
Modeling and prediction on grinding force in ultrasonic assisted elliptical vibration grinding (UAEVG) of SiC ceramics using single diamond grain	72
Experimental investigation of temperature field and formability of compact fused granulation fabrication barrel	72
Multilevel variable control for impulse-discharge thermochemical truing of diamond cutting edges in precision grinding	71
On mechanism of tool-workpiece separation in multi-dimensional vibration-assisted milling	70
Understanding the factors critical to the TIG welding of Cu components in bar wound electric motors	70
Multi-axis direct metal deposition process with effective regrouping strategy	70
Creating elemental gradient transition layer to improve the thermal fatigue resistance of femtosecond laser glass-metal welding	70
Stamping colors with solid-state superionic stamping (S4)	70
The flat bottom drill for bone drilling without plunging	70
Strategy for minimizing deformation of DLP 3D printed parts using sub-build plate	70
Effect of nanosized carbon black content on the microstructure, thermal stability, and mechanical properties of 3D printed poly urethane acrylate	70
The influence of post-thermal treatments on microstructure and mechanical properties in A20X alloy fabricated through powder bed fusion	69
An innovative process of clad teeming and rolling for preparing stainless steel/carbon steel clad plate	69
Micro-extrusion: A potential approach to micro-manufacture miniaturize magnesium metal matrix composite components	68
Novel insights into particle dynamics and deposition mechanisms during soft blade powder spreading in laser powder bed fusion	68