Plastics Rubber and Composites

Papers
(The median citation count of Plastics Rubber and Composites is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)
ArticleCitations
Experimental and numerical characterisation of fibre orientation distributions in compression moulded carbon fibre SMC48
Buckling analysis of tapered graphene-reinforced composite plates: an analytical approach25
Dr Arthur Wilkinson:1960–2022. A warm tribute from his close friend Prof Tony Ryan OBE20
Mechanical and tribological properties of chemically modified jute/epoxy composites17
Effect of silicon carbide particles on the mechanical, thermal and structural properties of recycled high-density polyethylene14
Mechanical and failure behaviour of PLA FFF printed part under sweat absorption: Splint arm application13
Manufacturing controlled asymmetric wrinkles for experimental studies of the effect of defects9
A comparative analysis of physico-mechanical and aging properties of non-apparel grade coarse wool–natural rubber flexible composites8
Development of polyamide 12 and high-density polyethylene/polyamide 6 blend composites reinforced with carbon fibre8
The influence of guide ring size on braid architecture7
Study on tribological properties of PI enhanced PTFE7
Investigation of the localised effects of multi-walled carbon nanotubes in pin-jointed composite structures6
Development of a new method for manufacturing hollow fibre-reinforced plastic structures for aeronautical applications using structural CFRP cores6
Synergistic intumescent flame retardant system based on zinc hydroxystannate and piperazine pyrophosphate for high-impact polystyrene composites with improved fire safety6
Improved wet skid resistance of NR/SBR composites induced by irradiation vulcanised styrene-butadiene rubber particles6
Numerical and experimental study of viscoelastic properties and energy absorption of functionally graded negative stiffness honeycomb made of Polyamide 125
Thermal stability and rheological properties of PMMA/B 2 O 3 nanocomposites synthesised by melting5
Conventional curing out-of-autoclave epoxy prepregs for in-situ manufacturing: Suitable or not?5
Optimization of strength properties of bamboo mesoparticles reinforced polyamide 6 using Box–Behnken approach5
Research status and prospect of wear and aging on hydraulic rubber sealing materials5
Expression of concern: “Influences of graphene oxide/sulphonated polyethersulphone nanoplatelets on the wettability, nanomechanical and tribological performances of polyethersulphone composites under 5
Investigations on the mechanical properties of PLA/Flax fibre composites obtained by Fused Filament Fabrication4
Effect of hybrid nano-fillers on the mechanical, thermal and viscoelastic properties of epoxy-based polymer composites for progressive applications4
Simulation of temperature field and optimisation of high-temperature parts for a giant mine tire4
Structural behaviour of polyethylene terephthalate glycol reinforced with carbon fibre through fused filament fabrication for automotive components4
Exploring the impact of UV-C radiation and UV-protective additives on SEBS thermoplastic materials4
Polyamide 6/carbon fibre composite: An investigation of carbon fibre modifying pathways for improving mechanical properties3
Polymer/carbon pin through thickness reinforcement3
The effect of acetylene black amount, operating pressure and temperature of capillary rheometer on thermal conductivity in natural rubber3
Evaluation of the tensile strength and impact property of polyamide/short glass fibre-multi-walled carbon nanotube composites: an experimental study based on response surface method3
Enhancing surface properties of FFF 3D printed nylon reinforced with kenaf fibres for dental prosthesis construction: An ANOVA-based analysis3
Fluoroelastomer/graphene nanoplatelets nanocomposite O-rings resistant to sour condensate for centrifugal pumps3
Auxetic behavior of eco-friendly natural fiber composites and their dependence on fiber surface modification3
Optimisation of tribological parameters of graphene nanoplatelet/polytetrafluoroethylene nanocomposites under engineered aqueous conditions using Taguchi integrated technique for order of preference b3
Mode-I fracture behaviour of aramid/glass-epoxy interply hybrid composites3
Crystallization induced segregated structure for outstanding conductive property with low percolation threshold3
Effect of MAPE on the morphological, physical and mechanical properties of GTR/PP composites produced by rotational moulding2
Insight into the crystalline morphology, thermal phase transitions and static, dynamic mechanical response of polypropylene hybrid composites reinforced with nanosilica and glass fibres2
Effect of tetrasilanolphenyl silsesquioxane on properties of sorbitol derivative-nucleated polypropylene cast films2
Interfacial interactions in rubber-based composites2
Effects of addition of clay and alumina nanoparticles on flame-retardant, thermal, and mechanical properties of polyolefin elastomer/magnesium hydroxide composite2
3D printing of sustainable wood-based bio-composites for high-end custom carton2
Effect of zinc dimethacrylate concentrations on properties of emulsion styrene butadiene rubber/butadiene rubber blends2
Statistic evaluation of optimal ABS fused filament fabrication parameters for wear and tensile strength control2
Tailored mechanical and thermal properties of polyphenylene sulphide (PPS) reinforced with nano-materials2
Thermomechanical modelling and wear analysis of poly aryl ether ketone incorporated with multi-walled carbon nanotubes and tungsten carbide nanoparticles2
Influence of the shape of silica nanoparticles on the elastic properties and glass transition temperature of PLA-based nanocomposites: Molecular dynamics simulation2
Synchronous biaxial stretching: An effective pathway to manipulate the structure-property relationship in polyimide films2
Comparative study on the impact response of polypropylene and epoxy matrix composites with respect to the plate thickness2
Water absorption and tensile properties of ground tire rubber/epoxy composites: effect of surface treatment2
Numerical modelling on polymer composites prepared via large area extrusion-deposition additive manufacturing: fibre orientation, material inhomogeneity, and thermal-mechanical responses during materi2
Determination of progressive damage modelling parameters and calibration studies of 8-harness satin weave S-2 glass fibre reinforced composites2
Influence of carbonyl iron powder on ethylene-propylene-diene monomer composites properties in different curing systems after thermo-oxidative aging1
The effect of polyvinyl chloride and polyethylene terephthalate on the mechanical properties of butyl rubber (IIR)-based thermoplastic elastomer using semi-efficient vulcanisation system and a nano zi1
The activation energy and electrical properties of polystyrene polymer with nickel bromide1
Analysis of composite/titanium alloy hybrid bolted structures based on improved LaRC05 criterion and backpropagation neural network1
Open-hole compressive response of angular stitched hybrid composites1
Densification of fibre-reinforced composite polymers under rotational moulding conditions1
Marble waste reinforced composite with tunable physico-mechanical and thermal properties: micromechanical simulation assisted experimental investigation1
Thermal and mechanical properties of carbon-based rubber nanocomposites: A review1
Preparation and characterisation of high damping poly(epichlorohydrin) (CO) and poly(epichlorohydrin- co -ethylene oxide- co 1
Exploring the use of TiO 2 filler in short Ficus Benghalensis natural fibre-based polymeric composites1
Phytolith-derived 2D nano-SiO 2 /PMMA composites: Preparation and properties1
The effects of resin rate (wt-%) on different temperature performance of newly designed friction composites for automobile brake lining applications1
Flexural behaviour modelling of carbon/epoxy laminates using the puck-EWM approach1
Evaluation of environmental impacts in PVC sector: the case of Turkey1
The effect of semi-curing on neat resin mode I fracture properties1
Numerical simulation of microstructural failure of natural fibre–hydrogel composites1
Carbon black and calcium lignosulphonate reinforced rubber composites with applied plasticiser glycerol1
Development of silver nanoparticles infiltrated PLA films for food packaging1
The effect of temperature and vulcanisation time on the thermal and mechanical properties of rubber used in tires1
0.046526908874512