OOIR: Observatory of International Research

Papers

(The median citation count of Chemical Industry & Chemical Engineering Quarterly is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-03-01 to 2024-03-01.)

Article	Citations
Production of bioplastic material from algal biomass	16
Dynamic optimization of low-density polyethylene production in tubular reactor under thermal safety constraint	11
Xanthomonas campestris biocontrol agent: Selection, medium formulation and bioprocess kinetic analysis	9
Impact of air temperature on drying characteristics and some bioactive properties of kiwi fruit slices	8
Clean printing process of cotton with natural dyes: Effect of paste formulation components on printing performances	8
Electrochemical harvesting of microalgae꞉ Parametric and cost-effectivity comparative investigation	6
Enhancing lipid extraction from green microalgae Chlorella sp. using a deep eutectic solvent pretreatment	6
Biosorption of lead ions from aqueous solutions by beech sawdust and wheat straw	5
The drying kinetics and characteristics of Shrimp dried by conventional methods	5
Drying kinetics and energy efficiency of microwave-dried lemon slices	5
Techno-economic analysis of catechin mix manufacture from Camellia sinensis leaves using green extraction technology	5
Experimental heat transfer studies on copper nanofluids in a plate heat exchanger	5
Comparison of corrosion behaviour of copper and copper alloys in aqueous chloride solution	5
Circular economy in apple processing industry: Biodiesel production from waste apple seeds	4
Preparation and characterization of PVA-SiO2 nanocomposite membranes for seawater desalination by pervaporation	4
Drying characteristics of blue mussels by traditional methods	3
Two phase leaching for metal recovery from waste printed circuit boards: Statistical optimization	3
Cellulose acetate butyrate graphene oxide nanocomposite membrane: Fabrication, characterization, and performance	3
Optimization of low-cost cow dung based activated carbon for the removal of carbofuran from aqueous solution	3
CMC of diverse Gemini surfactants modelling using a hybrid approach combining SVR-DA	3
Improvement of the monochlorobenzene separation process through heat integration: A sustainability-based assessment	3
Pine cones powder for the adsorptive removal of copper ions from water	3
Chemical engineering methods in analyses of 3D cancer cell cultures: Hydrodinamic and mass transport considerations	2
Modeling and simulation of the biosurfactant production by enzymatic route using xylose and oleic acid as reagents	2
Preparation and physicochemical properties of naturally grown green Spirogyra algae biodiesel	2

Heat transfer studies of Al2O3/water-ethylene glycol nanofluid using factorial design analysis	2
Obtaining xylitol by hydrolysis-hydrogenation of liquors derived from sugarcane bagasse	2
Dyeing of polyester fibers with sulfur- and nitrogen-containing anthraquinone derivatives	2
Evaluation of combined radiation for the treatment of lamivudine and zidovudine via AOP	2
A review on modeling of proton exchange membrane fuel cell	2
The study of direct dye sorption on flax fibers during dyeing	2
Combustion performance of bio-gasoline produced by waste fish oil pyrolysis	2
Multivariate statistical optimization of the ethanol fuel dehydration process using ionic liquids	2
Heat transfer studies in a plate heat exchanger using Fe2O3-water-engine oil nanofluid	2
Studies on thermophysical property variations of graphene nanoparticle suspended ethylene glycol/water	2
Effects of soft water attack on Portland and natural zeolite blended cements	2
Mango seed kernel oil extraction with ethanol: Optimization of oil yield and polyphenol	2
Investigation of the thin layer drying of micropropagated Ocimum basilicum L: Modeling by derived equations, quality characteristics, and energy efficiency	1
Magnesium removal from phosphoric acid by precipitation: Optimization by experimental design	1
Performance study of electrochemical micromachining using square composite electrode for copper	1
Storage time effect on inoculated, osmodehydrated chicken meat-microbiological and chemical characteristics	1
Light olefin production using the mixture of HZSM-5/MCM-41 and γ-Al2O3 as catalysts for catalytic pyrolysis of waste tires	1
Determination of the residence-time distribution in industrial dryer for the production of recycled polyester	1
Numerical study of turbulence on drag coefficient determination for particle agglomerates	1
pH control in sodium chlorate cell for energy efficiency using PSO-FOPID controller	1
Influence of yeast extract enrichment on fermentative activity of Saccharomyces cerevisiae and technological properties of spelt bread	1
Novel allyl-ester-based polymers as flow improvers for waxy crude oil	1
Electrochemical harvesting of Chlorella sp.: Electrolyte concentration and interelectrode distance	1
CO2 mitigation studies in packed absorption column using iron oxide nano fluid	1
Effect of different carbon sources on vacuum carbothermal reduction of low-grade phosphorus ore	1
Fluoride removal from phosphogypsum: A study on pre-industrial scale and its mathematical analysis	1
Enhanced photocatalytic oxidation of reactive dye using manganese catalyst complex	1
Microstructure and fracture mode of unalloyed dual-phase austempered ductile iron	1
Effects of pretreatments on drying of Turkey berry (Solanum torvum) in fluidized bed dryer	1
Green grape marc biosorbents preparation for mercury removal in aqueous media	1
Artificial neural network modeling for drying kinetics of paddy using a cabinet tray dryer	1
Hydrodynamic studies in two - phase stirred fluidized bed with three types of impellers	1
A computational study of a multi-solid-liquid fluidized bed incorporating inclined channels	1
Newly suggested shapes of impellers for stirring highly viscous fluids in vessels	1
The flow and mass transfer characteristics of concentric gas-liquid flow in an advanced static mixer	1
Green chemical production based on thermal cracking of inedible vegetable oil	1
Optimal dissolution and viscoelastic behavior of polyamide-66 in formic acid for membrane fabrication	1
Evaluation of different mathematical models in the CFD-DEM simulation of conical spouted bed fluid dynamics	1
Energy analysis of the convective drying of iron ore fines	1
Factorial design and surface method to optimization ethylic biodiesel production from chicken wastes	1
Phenol removal using pulsation bubble column with inverse fluidization airlift loop reactor	1
Effect of different electrolytes on electrochemical micro-machining of SS 316L	1
Study on heat exchangers and industrial absorption column for drying polyethylene terephthalate	1
The reduction of FCCU afterburning through process optimization and regenerator revamping	1
Bioaccumulation and biosorption study of heavy metals removal by Cyanobacteria Nostoc sp.	1
The effect of metal-titania interaction on photodegradation in SBA-15-supported metal-titania photocatalysts	1