OOIR: Observatory of International Research

Papers

(The median citation count of Advanced Engineering Materials is 2. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Study of a Piezoelectric Energy Harvesting Collaborative Strategy Based on the Synergy of Multifrequency Technique and Magnetic Nonlinear Technique	169
Preparation and Properties of Self‐Setting Calcium Phosphate Scaffolds: Effect of Pore Architecture	132
Machining Properties of Stone‐Plastic Composite Based on an Empirically Validated Finite Element Method	103
Ultra‐Shallow Flat Heat Waves on Low Thermal Conductivity Flexible Polyimide Substrate for Millisecond Thermal Analysis of Materials and Bioelectronic Applications	98
Dynamic Response and Energy Absorption of 5052 Aluminum Honeycombs with Gradient‐Thickness Cell Walls under Low‐Velocity Impact	88
	84
Design and Development of In‐Process‐Resolution‐Tunable Stereolithography System Utilizing Two‐Photon Polymerization	83
Microstructure, Mechanical Properties, Corrosion Behavior, and in Vitro Assessment of Mg‐Zn‐Cu Alloy for Gastrointestinal Anastomosis Staple Application	78
Tailored Nickel Base Multilayer Systems with Adjusted Grain Size and Chemical Composition	77
Issue Information	77
Resistive Switching of Perovskite‐Type Oxides Using the Hebb–Wagner Polarization Method	75
Bioactive Fe Foam for Degradable Bone Graft Cages	73
Scutoids as Building Blocks for Topologically Interlocking Material Systems	72
Impact of Sample Preparation Approach on Transmission Electron Microscopy Investigation of Sputtered AlNi Multilayers Used for Reactive Soldering	69
Issue Information	65
Modeling and Accessing Smart Materials with Integrity Constraints in the Shapes Constraint Language and Ontologies—The SmaDi Way	65
Smart Building Material with Near‐Infrared‐Triggered Reversible Color Switching	64
Parameters Optimization of Active Flexible Tool‐Assisted Shear Thickening Polishing Method for Concave Surface	62
Masthead	62
Editorial for Special Issue of Field‐assisted Materials Processing: Recent Innovations and Microstructural Evolution	62
Comparative Study on Microstructure, Corrosion Morphology, and Friction Wear Properties of Layered Double Hydroxide/Steam Coating Composite Coatings on Mg–Li Alloy	61
Failure Mechanism‐Based Assessment of Damage Tolerance in Cr–Ni Alloy Steel: Synergistic Stress–Crack–Life Interaction and Carburization Influence	60
High‐Temperature Oxidation Behavior of (Ti _0.8 Nb _0.2 )C–10 wt% SiC Composite Ceramics with Enhanc	60
Hf Addition Enhances Structural Stability and Mechanical Properties of NiTi Alloys across a Broad Temperature Range	59
Laser‐Powder Melt Pool Solidification Dynamics and Microstructural Engineering of Ti‐5553 Microlattices	59

Enhancing Fatigue Performance by Tuning of Residual Stresses in Welded Joints through Nanometallic Multilayer	56
A Study of Tribological Properties on Epoxy Resin Sealed 8YSZ Coating Under Various Environments	54
Embedding Function within Additively Manufactured Parts: Materials Challenges and Opportunities	54
Preparation of High‐Performance WC–MgO Composites by Spark Plasma Sintering	53
Adjustable Plasmonic Core–Shell Nanoparticles for Personalized Color Vision Correction	52
Core‐Shell Heterostructural Design Enables Spark Plasma Sintered Ti‐Zn Alloys With Superior Mechanical Properties	51
From Damage to Functionality: Remanufacturing of Thrust Roller Bearings by Tailored Forming	50
Trace Nickel Activated Biphasic Core‐CuO _ii /Shell‐CuO _i Secondary Microspheres Enable Room Temper	49
Numerical Simulation of Physical Field During Different Ultrasonic‐Power‐Assisted Casting of 7085 Aluminum Alloy	49
Effect of Sc Addition on Magnetocaloric Properties of GdTbDyHo High‐Entropy Alloys	48
Exploring Microstructure–Physical Property–Corrosion Response Relationship in Intermetallic Compounds of Al‐Cu Bimetallic Interfaces	47
Inkjet Printing on Hydrophobic Surface: Practical Implementation of Stacked Coin Strategy	47
The Grain Size Evolution Mechanism of A517Q Alloy Steel Fabricated by Laser and Wire Additive Manufacturing Assisted with Different Ultrasonic Vibration Treatments	46
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites	45
Observation of Strain Glass Transition in Additively‐Manufactured TiNiCu Alloys	45
About the Impact of Defect Phases on the Thermoelectric Properties of Cr₃S_4–xSe_x	45
Effect of Hydroxyapatite on Hot Deformation Behavior and Processing Map Development of Biodegradable Magnesium‐3 wt.% Zinc‐Based Composites for Orthopedic Applications	45
3D Investigation of Damage During Strain‐Controlled Thermomechanical Fatigue of Cast Al–Si Alloys	45
Preparation and Properties of Micro‐Arc Oxidation/Self‐Assembly Coatings with Different Hydrophobicities on Magnesium Alloy	44
Evaluation of the Potential of Laser Shock Peening Compared with Cold Expansion for Improving Fatigue Resistance of Riveted Lap Joints of Aerospace Grade 7175 Al Alloy	44
Physics‐Informed Multistage Machine Learning Strategy for the Nanomachining‐Induced Plastic Deformation Behavior	41
Surface Effect on Phase Transformation of Single Crystal NiTi Shape Memory Alloys Studied by Molecular Dynamics Simulation	41
Engineering the Atomic Interface of Refractory‐Metal‐Reinforced Copper Matrix Using Direct Ink 3D Printing	41
High‐Throughput Production of Gelatin‐Based Touch‐Spun Nanofiber for Biomedical Applications	40
Effect of Laser Printing Mode on Surface Topography, Microstructure, and Corrosion Property of Additive‐Manufactured NiTi Alloy	39
Research on the Microstructural Evolution of a Novel AlMgZnErZr Alloy during the Cold Stretching Process	39
Metal–Matrix Composites from High‐Pressure Torsion with Functionalized Material Behavior	38
Toward the Improvement of the Short‐Loop Recycling of Dy‐Rich Nd–Fe–B Permanent Magnets: Experimental and Numerical Approaches	37
Effect of CeO ₂ @Ni on the Oxidation Resistance of in Situ TiC/Ni Composite Applied for Intermediate Temperature Solid Oxide Fuel Cell Interconnects	36
Dielectric and Energy Storage Properties of Layer‐Structured Ba_n−3Bi₄Ti_nO_3n+3 (n = 4–7) Ferroelectrics	36
Microcellular Poly (Ethylene‐Co‐Vinyl Acetate)/Lignin Nanocomposites for Soft Ferroelectrets	36
Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization	36
Chromium Coatings Applied to Zr Alloy Claddings by Cathodic Arc Ion Plating: Effect of Nitrogen Inclusion on Limiting Columnar Defects	35
High‐Strength Joints on Glass and Aluminum Alloys Through Microstructure Surfaces at Low Temperature	35
Adapting Shot Peening for Surface Texturing Using Customized Additive Manufactured Shots	35
Application of GTN Damage Model Based on Hill’48 Anisotropic Yield Criterion in Forming of ZK60 Magnesium Alloy Sheets	34
Breaking the Cardiovascular Flow Barrier for Dielectric Elastomer Actuator‐Based Pumping: Design and Characterization	34
Achieving Reversible Asymmetric Surface Morphology via Metaregulated Layer	34
Strengthening Near‐ α Titanium Alloys via Phase‐Transformation‐Induced High‐Density Nanotwins	33
Emerging Functional Metals in Additive Manufacturing	33
Analysis of the Meso‐Mechanical Deformation Behavior of Al Foams and Ni/Al Hybrid Foams Using Time‐Lapse Micro‐Computed Tomography Measurements and 3D Optical Flow	33
Bessel‐Beam Direct Write of the Etch Mask in a Nano‐Film of Alumina for High‐Efficiency Si Solar Cells	32
Hierarchical Porosities Strategy to Enhance the Absorbing Performance of Graphene Aerogels	32
The Effect of Anion Modification on the Conductive Polymer/Ag‐Interdigitated Electrodes Micro‐Supercapacitor	32
Modeling and Re‐Examination of Nonlinear Vibration and Nonlinear Bending of Sandwich Plates with Porous FG‐GPLRC Core	32
Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites	31
Janus Paper‐Based Wound Dressings for Effective Exudate Absorption and Antibiotic Delivery	31
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions	31
Homogenization Heat Treatment and Tribological Properties of In Situ Alloyed NiTiCu by Laser Powder‐Bed Fusion	31
Magnetically Responsive Superhydrophobic Surfaces with Droplet Manipulation Capability	31

Electric Current‐Assisted Sintering of 8YSZ: A Comparative Study of Ultrafast High‐Temperature Sintering and Flash Sintering	31
Fatigue Resistance of an Anodized and Hardanodized 6082 Aluminum Alloy Depending on the Coating Thickness in the High Cycle Regime	30
Atmospheric AACVD Growth of Nd ³⁺ : ZnO Thin Films With Temperature‐Optimized Crystallinity and Up‐Conversion Quantum Yield	30
Geometry‐Faithful Strain Normalization for Interface‐Controlled Strengthening in Phase‐Transforming Filamentary Composites	30
Micromodification of Metal Oxides and Their Applications in Fiber‐Optic Sensing: A Review	30
Latest Advances in Manufacturing and Machine Learning of Bulk Metallic Glasses	30
Microstructure‐Informed Analysis Framework for Lattice Structures: Guiding Topology‐Material Synergy in Titanium Alloys	29
Tailored Mechanical Properties of the Poly(L‐Lactic Acid) Lattice Structure by Polymorphic Isothermal Crystallization Kinetics Control During Laser Powder Bed Fusion Process	29
Investigation into the Mitigation of Crevice Corrosion of Aluminum–Copper Contacts in Seawater by Regulating the Contact Surface Roughness	29
Predicting Mechanical Properties of AlCoCrFeNi High‐Entropy Alloys Using Machine Learning and Molecular Dynamics	29
Selective Laser Sintering versus Multi Jet Fusion: A Comprehensive Comparison Study Based on the Properties of Glass Beads‐Reinforced Polyamide 12	29
Approaching 1 GPa Ultra‐High Tensile Strength in a Nanostructured Al–Zn–Mg–Cu–Zr–Sc Alloy Prepared by Severe Plastic Deformation	29
Tuning Aluminum Content to Enhance Stress Rupture Properties of High‐Tungsten Superalloy	28
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing	28
4D Metamaterials with Zero Poisson's Ratio, Shape Recovery, and Energy Absorption Features	28
Ultra‐Broadband and Reconfigurable Liquid‐Based Microwave Metasurface Absorber	28
Spinodal Decomposition of B2‐phase and Formation of Cr‐Rich Nano‐precipitates in AlCoCrFeNi_2.1 Eutectic High‐Entropy Alloy	28
Mechanical Properties of Aluminum Matrix Syntactic Foams Manufactured with Aluminum Smelter Waste	28
Self‐Repairing Effect of Nanoserpentine Mineral Powder as an Additive on Steel/Aluminum Alloy Tribological Interface Under Oil Lubrication	28
Materials and Manufacturing for Ankle–Foot Orthoses: A Review	27
The Effect of Number and Size of Cellular Structures on Compressive Properties, Deformation Behavior, and Energy Absorption Characteristics of Ti6Al4V Lattice Structures Fabricated by Selective Laser	27
Direct Fused Deposition Modeling 4D Printing and Programming of Thermoresponsive Shape Memory Polymers with Autonomous 2D‐to‐3D Shape Transformations	27
On the Effect of Creep on Local Lattice Orientation in Single‐Crystal Ni‐Based Superalloy Microstructures	27
A Time‐Saving Method for Evaluating the Fatigue Strength of Carburized High‐Alloy Steel Containing Carbides	27
Tribological and Electrochemical Performance of Ag‐Doped and Undoped Different Ceramic Oxide Coatings Produced by Successive Ionic Layer Adsorption and Reaction on Ti6Al4V‐Extra‐Low Interstitial Alloy	27
Topology Optimization of Lattice Support Structure for Cantilever Beams Fabricated Via Laser Powder Bed Fusion	26
Printing Completely Conformal Liquid Metal Circuits on Arbitrary Curved Surfaces via Customized Conformal Mask	26
A Novel Ceramic‐Liquid Alloy Lattice Metastructure for Thermal Protection in Aerospace Applications	26
Polyvinylidene Fluoride Nanocomposites as Piezoelectric Nanogenerator: Properties, Fabrication and Market Applications	26
Experimental and Numerical Studies of Densification and Grain Growth of 8YSZ during Flash Sintering	26
Dimensionless Investigations on Energy Conversion and Analysis of Interlayer Time in Laser‐Based Powder Bed Fusion of Polymers for Polyamide 12 with Nanoadditives and Polypropylene	26
Recent Advances in the Additive Manufacturing of Stimuli‐Responsive Soft Polymers	26
Influence of Annealing Temperature on the Microstructure and Properties of Powder Metallurgy AlCoCrFeNi High‐Entropy Alloy	26
Defect Sensitivity in Ultrasonic Testing of Al ₂ O ₃ /Epoxy Composites: Insights from Multiscale M	25
Controlled Synthesis of Hydroxyapatite Coating with Crystal Defects for Enhanced Corrosion Protection	25
Development and Performance of 3D‐Printed Nanohydroxyapatite Polyamide 66 Artificial Vertebral Body	25
Strength of Disordered and Ordered Al‐Containing Refractory High‐Entropy Alloys	24
Effects of Friction Surfacing on Microstructure and Properties of LA103Z Magnesium–Lithium Alloys	24
3D Printed Design‐Assisted Multilayered Graphene Oxide‐Modified Polymer Glucose Sensor	24
Preparation and Compression Behavior of Multiscale Hierarchical Porous Copper with High Porosity	24
Structural Design of Multifunctional PET Non‐woven Fabric with Porous Dual‐Network for Infrared Stealth, Flame Retardant, and Electromagnetic Interference Shielding	24
Issue Information	24
Energy Field‐Assisted Additive Manufacturing of Engineering Thermoplastics	24
Enhanced Magnetoelectric Coupling in Lead‐Free BaZr _0.05 Ti _0.95 O ₃	23
Incorporating the Antioxidant Fullerenol into Calcium Phosphate Bone Cements Increases Cellular Osteogenesis without Compromising Physical Cement Characteristics	23
Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS	23
Compressive Behaviors and Deformation Mechanisms of Open‐Cell AlSi Foam	23
Analysis of the Quasistatic Nonlinear Mechanical Model of Hemispherical Shell Metal Rubber	23
Recyclable Near‐Hemispherical Aligned Porous Piezoceramics for Green Catalysts	23
Improved Corrosion Resistance of Ni‐Based Alloys by B‐Induced Passivation Behavior	23
Investigation of Sn–3.0Ag–0.5Cu Bump Arrays Prepared by the Pulsated Orifice Ejection Method	23
Noninvasive Deterministic Nanostructures Lithography on 2D Transition Metal Dichalcogenides	23
Construction of Core‐Shell Structure in PA6/ABS/SEBS Blends for Achieving Stiffness‐Toughness Balance	22
A Novel PowderMEMS Technique for Fabrication of Low‐Cost High‐Power‐Factor Thermoelectric Films and Micro‐Patterns	22
Masthead	22
Laboratory‐Scale Procedure for Evaluating the Flux Efficiency on Melt Cleanliness and Tensile Properties of Recycled Aluminum Alloys	22
Low‐Cycle‐Fatigue Performance of Stress‐Aged EN AW‐7075 Alloy	22
	22
Solar‐Assisted, Highly Efficient, and In Situ Recovery of Crude Oil Spill by FeCo₂S₄‐Modified Sponge	22
On the Investigation of a Sustainable Two Step Laser‐Based Surface Treatment for the Functionalization of Additive Manufactured Ti–6Al–4V Components	22
Near‐Threshold Fatigue Crack Propagation in Sintered 304L Stainless Steel Compact with Network Structure Composed of High‐Entropy CrMnFeCoNi Alloy	22
Magnetic‐Driven Micro‐Gear Pair Fabricated by Femtosecond Laser Writing	22
Prediction of Macroscopic Deformation Bands in Porous Metals with Unidirectional Through‐Pores	21
A Stable Broadband Antireflective Structure on MgAl₂O₄ Fabricated by Spatially Shaped Ultrafast Laser Pulses	21
Tribological Properties and Corrosion Resistance of AlCrFeNi_3.1Mo_x Eutectic High‐Entropy Alloy Coatings via Laser Cladding	21
Fatigue Behaviors and Dislocation Evolution of Copper and Aluminum Alloy	21
Influence of Friction Stir Weld Parameters on the Corrosion Susceptibility of EN AW‐7075 Weld Seam and Heat‐Affected Zone	21
Recent Advances in 3D‐Printed Multifunctional Thermally Deformed Metamaterials	21
Finite Element Analysis of Ceramic–Composite Structures for Ballistic Applications: Effect of Ceramic Thickness and Cell Structure	21
Multifunctional, Coarse Grained, Refractory Composites for Large Volume Key‐Components in High Temperature Processes	21
Refreshing Industrially Processed 6xxx Series Aluminum Alloys after Prolonged Natural Aging	21
Preparation of Multiscale Slippery Liquid‐Infused Porous Surface Based on Ti6Al4V Alloy with Self‐Cleaning, Stability, and Self‐Healing Properties	21
Biopolymer Composites Material Extrusion and their Applications: A Review	21
	21
Improving the Mechanical Properties of Low‐Carbon Steel by In Situ Strain Aging	21
Single‐Crystal Castability of CM186LC Nickel‐Based Superalloy	21
Achieving a Strong Friction‐Lap Joint of Continuous Carbon‐Fiber‐Reinforced Plastic/Aluminum Alloy via a Surface Laser‐Processing Pretreatment	21
Wire‐Intertwined Hierarchical Lattice Structure: Improved Energy Absorption Stability and Modified Failure Mode	20
Mechanical Properties of Cochiral and Contrachiral Mechanical Metamaterials Under Different Temperatures	20
Profilometry‐Based Indentation Plastometry Testing for Characterization of Case‐Hardened Steels	20

Energy Absorption Characteristics of Coupled Auxetic Metamaterials with Enhanced Local Stiffness	20
3D Printing of Ceramics with Controllable Green‐Body Configuration Assisted by the Polyvinyl Alcohol‐Based Physical Gels	20
Microstructural Evolution and Properties of ZrB₂‐Reinforced AA6111 Aluminum Matrix Composites Subjected to Double‐Sided Friction Stir Processing	20
Effect of Thermomechanical Processing on the Impact Deformation of Additively Manufactured 316L Stainless Steel	20
Mechanistic Understanding of Cu‐Driven Inclusion Transformation and Pitting Suppression in Carbon Steel	20
Assessing the Microstructure of SnBiZn Alloys during Semisolid Treatment	20
Effect of Nano‐TiC Ceramic Particles on Microstructures and Properties of High‐Cr Steel under Different Heat‐Treatment Conditions	20
New Generation Beta‐Gallium Oxide Nanomaterials: Growth and Performances in Electronic Devices	20
Modular Soft Robotic Actuators from Flexible Perforated Sheets	20
Synthesis and Characterization of BaZrS₃ Thin Films via Stacked Layer Methodology: A Comparative Study of BaZrS₃ on Zirconium Foil and Silicon Carbide Substrates	20
Fatigue Strength Assessment of Laser Beam Welded Joints Made of AA7075 and Magnetic Pulse Welded Joints Made of AA7075 and 3D‐Printed AlSi10Mg	20
Mechanisms of High‐Temperature Corrosion Resistance in Al–Si–Cr and Ni–Cr Coatings for Low‐NO _x Co	20
Multifunctional Coatings on Mg‐Based Metallic Biomaterials and Implants	20
Non‐Hetero‐Deformation‐Induced Hardening in Steel/Polymer/Steel Layered Sheet: Experiment and Modeling Analyses	20
Continuous Stiffness Graded Metal–Ceramic Femoral Stems: UMAT‐Based Design and Finite Element Assessment	20
Reinterpretation for Modeling Carbon Partition by Thermo‐Kinetics	20
SiC Particle‐Reinforced Ti‐Al Laminated Composites Cutting Removal Mechanism and Thermo‐Mechanical Characteristics	19
Microstructural and Mechanical Characterizations of Mo/W and Mo/Graphite Joints with BNi2 Paste	19
Fabrication of a Stable, Low‐Cost, Patient‐Specific, Brain Phantom with Ventricles for Ultrasound Imaging	19
Influence of a Preageing Treatment on the Cluster Formation and the Further Ageing Route in Al–Mg–Si Extrusion Alloys	19
Residual Stress Relief in Graphite/Cu Brazed Joints by Inserting Carbon Fiber Felt	19
Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates	19
Ti₃C₂T_x‐MXene‐Based Color‐Indicative All‐Organic Electrochromic Supercapacitors	19
High‐Performance Piezoelectric Nanogenerator and Self‐Charging Photo Power Cell Using Hexagonal Boron Nitride Nanoflakes and PVDF Composite	19
Geometric‐Bifurcation Methods for Dual Order‐Disorder Transitions: Applications to the Isotropic‐to‐Smectic A Phase Transformation	19
Fabrication of Multifunctional Integrated Composites with Excellent Mechanical Synergistic Effects Producing from Aramid Honeycomb and Rigid Polyimide Foam	19
Innovative Vibration Control of Triply Periodic Minimum Surfaces Lattice Structures: A Hybrid Approach with Constrained Layer Damping Silicone–Viscoelastic Layer Integration	19
Elastomers for Soft Electronics: A Review from the Material's Perspective	19
Development of High‐Entropy Materials: A Review of Milestones Over the Last 20 Years	19
Microstructure and Mechanical Properties of NiTi Shape Memory Alloys by Laser Engineered Net Shaping	19
Magnetoelectric Core–Shell Nanoparticle–Based Wearable Hybrid Energy Harvesters for Biomedical Applications	19
Deformation Behavior of 3D‐Printed High‐Entropy Alloys: A Critical Review	19
Experimental Study on Ultrasonic Milling Textures for Collaborative Wear	19
Recent Advances in Poly(N‐isopropylacrylamide) Hydrogels and Derivatives as Promising Materials for Biomedical and Engineering Emerging Applications	19
Dual‐Phase Enabled Sinusoidal Current Anodizing for Efficient Preparation of High Specific Capacitance Anode Aluminum Foils	19
Effect of Optimization of Texture Density on Improving the Tribological Properties of Metal Friction Pairs with Different Hardness Ratios	19
Impact of PbZr_0.5Ti_0.5O₃ Particle Size on the Ferroelectric and Magnetoelectric Properties of Mn_0.5Zn_0.5Fe₂O₄–PbZr_0.5<	19
Improved Mechanical Performance of Epoxy Systems with Low Loadings of Milled Carbon Fiber via Chemical Surface Modification	19
Microstructure Evolution and Mechanical Properties of Commercially Pure Titanium Sheets after Thermomechanical Treatment with Cold Rolling and Annealing	19
Study of Mechanical Properties of a New 3D Re‐Entrant Lattice Auxetic Structure Under Bending	19
Air Cooling Martensites—The Future of Carbon Neutral Steel Forgings?	18
A Physical‐Based Constitutive Modeling Coupled With Dynamic Spheroidization and Phase Transformation for Bimodal Ti–6Al–4V Alloy Within α+β Region	18
Powder‐Based Additive Manufacturing: A Critical Review of Materials, Methods, Opportunities, and Challenges	18
Adjustable Energy Absorption of Triply Periodic Minimal Surface Structures via Additively Reconfigurable Manufacturing‐Based Investment Casting	18
Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties	18
Reinforcement of 3D‐Printed Re‐Entrant Structures using Additional Supports under Three‐Point Bending, Experimental and Numerical Analyses	18
Front Cover: Development of Sustainable MgO–C Refractories Using MgO–C Recyclates and a Novel Eco‐Friendly Fructose–Tannin Binder Crosslinked With Citric Acid (Adv. Eng. Mater. 10/2026)	18
High‐Rate Deposition and Characterization Study of CoZrO Films for On‐Chip Power Applications	18
Overcoming Moisture‐Induced Degradation in Organic Solar Cells	18
Interfacial Microstructure Evolution and Compressive Behavior of Asymmetric Aluminum Foam Sandwich Fabricated by Coupling Two‐Step Foaming With Vacuum Bonding	18
Robust PFAS‐Free Superhydrophobicity Exhibited in Hierarchically Nanostructured Coatings on Textiles	18
High‐Throughput Design of Refractory High‐Entropy Alloys: Critical Assessment of Empirical Criteria and Proposal of Novel Guidelines for Prediction of Solid Solution Stability	18
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies	18
Instrumented Dynamic Penetration of Sandwich Panels with Auxetic and Non‐Auxetic Core using Direct Impact Hopkinson Bar	18
Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study	18
Tooling in Spark Plasma Sintering Technology: Design, Optimization, and Application	18
Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices	18
Optimized Strategy for Fabricating High‐Aspect‐Ratio Periodic Structures Over Large Areas Using ps‐Direct Laser Interference Patterning	18
4D Quantification of Surface Topography‐Dependent Corrosion Progression in Electron Beam Additive Manufactured 316L Stainless Steel	18
Self‐Healing Waterborne Polyurethanes as a Sustainable Gel Electrolyte for Flexible Electrochromic Devices	18
Anticorrosive Behavior of a Novel Ternary RGO–ZnO–PANI Nanocomposite‐Reinforced Epoxy Coating on Mild Steel in Marine Environment	18
Reactive Interaction and Wetting of Fe‐ and Mn‐Containing, Secondary AlSi Alloys with Manganese Oxide Ceramic Filter Material for Fe Removal	18
Hybrid Material Extrusion Process Optimization for Printability and Adhesion in 3D‐Printed Electronics	17
Observing High‐Cycle Fatigue Damage in Freestanding Gold Thin Films with Bulge Testing and Intermittent Transmission Electron Microscopy Imaging	17
In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy	17
Exploring the Effect of Lanthanum on the Corrosion Resistance and Antimicrobial Properties of Fe–20Cr–18Ni–6Mo–0.8Cu–0.2N Stainless Steel in Seawater	17
Advanced Printing Transfer of Assembled Silver Nanowire Network into Elastomer for Constructing Stretchable Conductors	17
Tribocorrosion Characteristics of Hard Anodized Al Alloys on Hydrogen Valve Application for Fuel Cell Electric Vehicles	17
Behavior of Different β Stabilizers on the Microstructure and Properties of Ternary Ti‐3Sn‐X Alloys	17
On the Monotonic and Cyclic Behavior of an Al‐Mg‐Zn‐Cu‐Si Compositionally Complex Alloy	17
Tough, Bioinspired Transparent Glass‐Ceramics	17
Effect of Multidirectional Fiber Architecture on the Microstructure, Mechanical, and Tribological Properties of C_f‐SiC_m Composites	17
A Rapidly Degradable Extruded Mg–Y–Zn–Ni Alloy for Fracturing Tool Applications	17
Laser Powder Bed Fusion of Titanium‐Coated Diamond‐Reinforced Aluminum Matrix Composites	17
	17
Piezoresistive Effects in a Highly Sensitive Conductive Elastomer: Experiments and Artificial Neural Network Study	17
Laser Powder Bed Fusion of Pure Zinc Electrodes for the Manufacturing of Biodegradable Batteries: Process Development and Preliminary Electrochemical Testing	17
Cover Picture	17
Effect of Ultrasonic Vibration on Microstructure and Properties of Ni‐Based Cladding Layers Reinforced by Chromium Carbide In Situ Generated	17
Prediction of Flow Stress and Characterizing the Deformation Mechanism of As‐Extruded 7005 Aluminum Alloy	17
Sensitive Label‐Free Immunoassay by Colorimetric Plasmonic Biosensors Using Silver Nanodome Arrays	17
Antimicrobial Studies of Black Silicon and Black Diamond Using Gram‐Positive Bacteria	17
Microstructure Characterization and Robust Lubrication Performance of CoCrNi Medium Entropy Alloy with Advanced Electrochemical Boronizing Treatment	17
Research Progress of Dental Restoration Materials and Their Applications	17
Synergistic Effects of Chain Extender and Poly(Methyl Methacrylate) on the Foaming Behavior of High‐Performance Poly(butylene Succinate) Foams	17
Natural Fucoidan and Bioactive ACH ₁₁ Peptides Multilayer Coating on Biodegradable Magnesium Alloy for Potential Application in Vascular Stent	17
A Low‐Energy Active–Passive Anti‐Icing Strategy for Wind Turbine Blades	17
Thermomechanical Responses of Microcracks in a Honeycomb Particulate Filter	17
Masthead	17
Evaluation of a Local Acoustic Resonance Method for Coating Thickness Determination on Stochastic Metal Hybrid Foams	17
Enhancing Neural Stem Cell Stimulation with Structured Piezoelectric Composites: An In Vitro Study	17
High Efficient Dye Adsorption and Facile Magnetic Recovery of PVA/XG/Fe ₃ O ₄ Hydrogel via Green I	16
The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282	16
Microscale Structure Additive Manufacturing Control Method Using Localized Electrochemical Deposition	16
On the Joining of High‐Strength Dissimilar Inconel 600 and SS316L Materials by Friction Stir Welding with Improved Mechanical Properties and Localized Corrosion Resistance	16