OOIR: Observatory of International Research

Papers

(The TQCC of Journal of Theoretical and Applied Mechanics is 2. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-06-01 to 2026-06-01.)

Article	Citations
Dynamic calculation of the fire zone for anti-aircraft artillery	31
Damage localization in the main structural elements of steel halls applying dynamic structural response signal and Discrete Wavelet Transform	15
Dimensional synthesis of suspension system of wheel-legged mobile robot	10
Design and experiment of membrane-type acoustic metamaterials used in EMUs to control low frequency noise	8
Damage evolution of vehicle motor rotor under single working condition based on GTN model	7
A fully-coupled three-dimensional fluid-structure interaction study on the externally-pressurized collapsible tube and the internal flow	6
Creep test and constitutive model for granite with different water content after high temperature cooling	6
Design of a semi-active suspension control method based on an enhanced inverse model for nonlinear magnetorheological dampers	5
Study of a horizontal seat suspension with a model of the seated human body and energy recovery braking subsystem	5
The influence of industrial and environmental factors on the polyoxymethylene	5
Analytical modelling and shape optimization of composite girder with adhesive bondline	5
Impact of honeycomb straightener parameters on operation in a straight duct	5
Sensitivity analysis of multiple eigenvalues and associated eigenvectors of quadratic eigenproblem	5
Probabilistic estimation of the dynamic gait parameters	5
Analysis of the contribution degree of vibration transmission of bolted structure	4
Instability mechanism and anchoring control technology of expansive weakly cemented soft rock roadway	4
Two tools for the science of material effort	4
Mechanisms of mining induced inrush of pressurized water in the floor containing faults	4
Mechanical performance of asphalt pavement with orthotropic unbound granular sub-base under vehicle load	4
Experimental studies of the flapping motion of a butterfly wing model	4
Study on ductile fracture criterion applied to shear fracture prediction of DP780 sheet	4
Nonlinear damping identification using an extended stabilized layers method	4
Influence of the shape of the copper component on the mechanical properties of the friction material used in the disc brakes	4
A fast and robust numerical solution for the positioning design of horizontal drains in a saturated-unsaturated soil ground system	4
Surrogate-based optimization of the layup of a laminated composite wind turbine blade for an improved power coefficient	4

Study of triaxial compression mechanical properties and pore-fracture characteristics of coal rocks in the Yili Basin, Xinjiang	3
Sensitivity to Gauss quadrature of isogeometric boundary element method for 2D potential problems	3
The probabilistic model for system reliability analysis of a steel plane and spatial trusses	3
The development of two multiaxial ductility factor predicting models based on creep cavity growth theory	3
Effect of water content on the mechanical behavior and energy evolution of soft rock under uniaxial compression	3
Tool for analysis of traffic of vertical take-off and landing aircraft in urban agglomerations	3
Investigation into resistance forces from the wheel-rail interface of a four-axle railway vehicle in curved track	3
Exploitation parameters of deformed high-strength steel assessed by the Barkhausen noise method	3
Collapse modes of concrete reinforced square bridge piers under vehicle collision	3
Comparative study of die materials for hot aluminium forming using an autonomous tribological testing system	3
Elastic buckling of a rectangular sandwich plate with an individual functionally graded core	3
Evaluation of shape transformation in 4D printed polylactic acid using copper wires	3
Evaluation of microstructure and mechanical properties of ferromagnetic structural steels using Barkhausen noise	3
Analysis of mechanochemical diffusion coupling processes based on transient continuum chemo-mechanical coupling theory	3
Tactical and strategic air traffic sequencing with minimum-fuel trajectories	3
Error measures and solution artifacts of the harmonic balance method on the example of the softening Duffing oscillator	3
Piezoresistive sensing mechanism of graphene-based electronic skin	2
Impacts of implementing stochastic excitation to assess anomalies on railway vehicle dynamic model.	2
Investigation of the pad stiffness effects on the initiation of brake squeal phenomenon	2
Use of the biaxial coefficient in determining life for a combination of cyclic bending and torsion of bronze RG7	2
Influence of geometrical defects on aerodynamic drag of non-watertight Ahmed body	2
Dynamic response of a guy line of a guyed tower to stochastic wind excitation: 3D non-linear small-sag cable model	2
Evaluation of tribological behavior of tribopairs in water hydraulic radial piston pumps with multiple coatings and lubrication	2
Assessment of aluminide coating integrity by using acoustic emission	2
Investigation of out-of-plane compression mechanical property for novel hierarchical reentrant honeycomb structures	2
Laminar flow past the bottom with obstacles - a porous medium approximation	2
Study on roof fracture mechanism and mine pressure characteristics in pseudo-inclined working faces of steeply inclined coal seams	2
Moment-curvature relation for laser-assisted bending of thin Inconel 718 beam	2
Study on the shear creep characteristics of anchored jointed rock masses under creep fatigue loading	2
On mitigation of oscillations of a mechanical system with two degrees of freedom in the vicinity of external resonances	2
Asymmetric Duffing oscillator: the birth and build-up of a period-doubling cascade	2
Research on hydrodynamic characteristics of a 200 m×175 m anchored-offshore photovoltaic under wind-wave-current loads	2
Response analysis and control of composite thin plate with piezoelectric actuators by Finite Element Method	2
Assessment of microstructural changes in S235 steel after cold rolling using eddy current testing	2
Numerical simulation of the particle settling in a Bingham fluid using the two-way coupling CFD-DEM scheme	2
Exploration of frequency characteristics of ball bearing with uneven load bearing effect caused by wear failure of multiple rolling bodies under starved lubrication	2
Dynamics modeling of variable mass systems – a case study of an underwater inertia based propelled glider performance	2
Determination of Chaboche and Bouc-Wen parameters for quenched and tempered steel	2
Diffraction of plane P-wave by an underwater tunnel	2
The comparison of robust and reliability based design optimization	2
Self-synchronization of drive vibrators of an antiresonance vibratory conveyor	2
Predicting the trajectory of a spinning ping pong ball during flight using three-dimensional coordinates	2
Transient vibration of a fractional viscoelastic cantilever beam with an eccentric mass element at the end	2
The effect of graphite flake diameter on the resistance to thermal shock, microstructure and mechanical properties of silicon carbide nanomaterials	2
Numerical study on micro-fracture characteristics of rock unloading failure under high stresses and the explanation for rock burst	2