OOIR: Observatory of International Research

Papers

(The TQCC of Mechanika is 2. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Optimization of Anti-Impact Energy Absorption Structure of Hydraulic Support	16
Experimental and Numerical Analysis of Helical Gear of Raw Mill in Hamma Bouzian Cement	16
Lubrication analysis of hydrodynamic-static hybrid bearing with deep-shallow chambers considering thermal conduction	15
Experimental Investigation of Suspended Water, Ethanol and Acetone Droplets Transient Phase Change Regimes in the Heated Airflow	13
Robot Workspace Optimization based on Monte Carlo Method and Multi Island Genetic Algorithm	10
Biomechanical Study of the Wing of the Dragonfly Aeshna Cyanea	8
Vibration Analysis of Porous Functionally Graded Material Truncated Conical Shells in Axial Motion	8
Simulation and Optimization for Hot Stamping Process of Rear Windshield Lower Crossbeam of Aluminum Alloy Automobiles	8
Fatigue Life Assessment of Cruciform Welded Joints Based on Interval Dissipation Energy Method	7
Model Updating Based on Bayesian Theory and Improved Objective Function	7
Investigation of Robotic System Parameters for 3D Scanning Human Limbs	7
Stress Analysis of Vibrating Screen Side Plate based on Elastic Theory	7
Nonlinear vibration characteristics and bifurcation control of a class of piecewise constrained systems with dynamic clearances	6
Heat Transfer Enhancement through Different Heat Sink/Impinging Air Jet Parameters an Experimental Approach	6
Investigating the Impact of Flow Profile on Heat Transfer in Nanofluid Flow: A Numerical Study	6
Effect of Suction and Injection on the Time-Varying Flow Produced by an Oscillating Porous Disk and a Newtonian Fluid at Infinity Rotating about Parallel Axes	5
Modeling and Analysis of Flexible Deployable Structure with Scissor-Like Elements Using a Novel Non-Locking Beam Element	5
Improved Particle Swarm Algorithm Based Multi-objective Optimization of Diaphragm Spring of the Clutch	5
The Research on Horizontal Motion Axis Control System Error Prediction of the Gantry-Type Vertical Machining Center	5
Application of Worm Optimization Algorithm to Design Challenges: A Focus on Pressure Springs	4
Development of mobile minirobots for in pipe inspection tasks	4
Fail-Safe Mass Reduction of a Heavy-Duty Front Axle Using Topology Optimisation	4
The Thermal Error Characteristic Analysis and Thermal Error Modeling Compensation of Aspheric Grinder	4
Vibration Characteristics Analysis of Twin-Screw Compressor Shell Based on the Fluid-Solid Coupling Method	4
Accessibility and Trajectory Planning of Cutter Changing Robot Arm for Large-Diameter Slurry Shield	4

A Novel Fault Diagnosis Method for Acceleration Sensor Utilizing IEM-Based LLE and WKELM	4
A Novel Principle Stress Model to Predict the Stress and Load in Sheet Drawing	4
Effects of Addition of Glass Fibers and SiC Particles on the Mechanical and Machinability Behaviours of Areca Fine Fiber-Reinforced Phenol Formaldehyde Composite	4
Modeling of Water Transport through Plasmodesmata in Plant Cell	4
Transient characterisation and analysis of shape memory alloy wire bundles for the actuation of finger joints in prosthesis design	3
Helical Baffle Thermohydraulic Performance Versus Segmental Baffle One	3
Research on Many-Objective Scheduling Optimization Method for the Large-Scale Hybrid System	3
Active Control for Transverse Vibration of the Marine Stern Shaft-Bearing System with LQR Strategy	3
Actuation Performance of Macro Fibre Composite (MFC) as Actuator in Vibration Reduction of Cantilever Beams	3
Optimization of Motion Parameters and Structural Stiffness of Spatial Four-Bar Weft Insertion Mechanism of Rapier Loom	3
Numerical Study of Particle Impingement on Aeroengine under Mixed-Phase Conditions	3
Structure Analysis for Plate Components Using an Advanced Boundary Element Method	3
Averaged Heat Fluxes Densities During Condensation and Evaporation of a Water Droplet	3
Numerical estimation of the influence of pre-induced micro-cracks in the stress concentration zone on the SIFs of a lower suspension arm	3
Optimization of restrictor parameters and static characteristics study on orifice type hydrostatic thrust bearing	3
Simulation Research on Non-Bevel Gear Transmission Mechanism	3
Lightweight Finite Element Analysis and Experimental Study of 90# Fifth Wheel	3
Performance of Elastohydrodynamic Inclined Fixed Pad Thrust Bearing with Ultra Low Clearance	3
The Structure Design and Precision Improvement of Small Caliber Non-Spherical Surface Type Detector	3
Investigation of Dynamics of the Manipulator with Self-Stopping Mechanism and Vibration Drive Based on Centrifugal Forces	3
The Characterization of the Plastic Instability of S235 Thin Steel Sheets by Multiple Regression and Analysis of Variance Methods	3
Numerical Modelling of Phase Transformations of Water Droplets for Efficient Heat Recovery from Biofuel Flue Gas	2
Research on Optimization Method of Vehicle Speed in Urban Road Conditions Based on Interval Analysis	2
Kinematics and Trajectory Planning of 3-PSS/7R Spatial Hybrid Re-dundantly Driven Mechanism	2
Ultrasonic Fatigue Testing Machine Based on Resonance Principle	2
Research on Error Compensation of CNC Machine Tool Based on Multibody System Kinematics	2
Experimental and Numerical Study on LCF Crack Propagation of Coiled Tubing Steel	2
Multiscale Elastohydrodynamic Wedge-Platform Thrust Bearing with Ultra Low Clearance	2
Influence of Strain Rate and Temperature on Compressive Properties and Energy Absorption Efficiency of Expanded Polystyrene and Flexible Polyurethane Foam	2
Development and Research of the Laser Engraving Process in Packaging Manufacturing Technology	2
Performance of a Small Hydrodynamic Journal Bearing Involving Adsorbed Layer and Surface Elastic Deformation	2
Unsteady Numerical Investigation Strategy of Natural Convection in an Isosceles Superimposed Triangular Enclosure	2
Research on Tribological Features of Brake Friction Materials - Comparison of the Results Obtained with the Pin-On-Disc and Ball-Cratering Methods	2
Fault Diagnosis of Anti-Friction Bearings Based on Bi-Dimensional Extensive Empirical Wavelet Decomposition and Optimized Incremental RVM	2
The Effect of the Radius of Curvature on the Joint Strength in Butt-Curved Lap Joints	2
The Modified Residual Property Model For Fracture Mechanics	2
Logistics Pure Electric Vehicle Routing Based on GA-PSO Algorithm	2
Development and Research of Technologies and Methods of Electro-flocking in the Decoration of Packaging Products	2
Combined Effects of Surface Adhering Layer and Surface Elastoplastic Deformation in Hydrodynamic Lubricated Line Contacts with Long-Chain-Molecule Fluids	2
The Improvement of Detection Precision of Internal Surface Detection System of Main Cylinder	2