OOIR: Observatory of International Research

Papers

(The median citation count of International Journal of Cast Metals Research is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-03-01 to 2024-03-01.)

Article	Citations
Influence of SAC and eggshell addition in the physical, mechanical and thermal behaviour of Cr reinforced aluminium based composite	34
Evolution of the surface quality and tool wear in the high speed turning of Al2219/n-B ₄ C/MoS ₂ Nano metal matrix composites	17
Investigation of the surface quality and dimensional accuracy of polymer patterns produced by selective laser sintering (SLS) method for investment casting (IC)	14
Structure-property correlation of eutectic Al-12.4 Si alloys with and without Zirconium (Zr) addition	10
strain induced melt activation (SIMA): original concept, its impact and present understanding	8
Effect of friction stir processing on microstructural and mechanical properties of lightweight composites and cast metal alloys – A review	8
Analysing Gray Cast Iron Data using a New Shapiro-Wilks test for Normality under Indeterminacy	7
On the heterogeneous nucleation pressure for hydrogen pores in liquid aluminium	6
The origin of thermal expansion differences in various size fractions of silica sand	6
The effect of ultrasonic melt treatment on solid solution treatment temperature and/or time for an Al-7Si-2Cu-1Mg alloy	6
Structure formation and multistep nucleation in CASTING Al-Mg-Si alloys	5
Microstructural, mechanical and tribological analysis of functionally graded copper composite	5
Surface modification of ductile iron produced by an innovative in-situ casting technique	5
A simple model to estimate hydrogen solubility in liquid aluminium alloys	4
On estimating the hydrogen solubility in solid aluminium alloys and the hydrogen solubility difference between the liquidus and solidus temperatures	4
Investigation of the effect of the addition of grain refiner and modifier addition on wear properties in sand and permanent mould casting of A357 and A380 aluminium alloys	4
Effect on mechanical and thermodynamic properties of Al-10Si-0.8Fe alloys with Al-Ti-C and Ce compound additions	4
Assessment of microstructure effects on tensile behaviour in silicon strengthened ductile irons produced through different cooling rates	4
Microstructure and mechanical properties of die-casting ADC12+x(La+Yb) alloy	4
Investigations on the suitability of banana peel powder as an alternative additive in synthetic green sand moulding system	4
Interfacial characteristics, mechanical properties and fracture behaviour of Al/Mg bimetallic composites by compound casting with different morphologies of Al insert	3
Determination of dendrite coherency point characteristics in Al-Si-Mg alloy	3
Mechanism of bonding of Fe/Al bimetal during heat treatment of compound cast parts	3
Measurement of Darcian Permeability of foundry sand mixtures	3
Improved interface bonding of Mg/aluminized steel bimetallic castings prepared by solid–liquid compound casting process	3

Extrema of micro-hardness in fully pearlitic compacted graphite cast iron	3
Optimisation of melt pouring temperature and low superheat casting of Al-15Mg₂Si-4.5Si composite	3
Effect of the cooling rate on the tensile strength of pearlitic lamellar graphite cast iron	3
Measurement and simulation of residual stresses in grey cast iron as a function of shake-out temperature	2
Rheological properties of ADC12 Al alloy in the semi-solid state	2
Simulations and experiments of mould filling in lost foam casting	2
Effect of cast iron microstructure on adherence of an epoxy protection	2
Effect of cooling rate on eutectic constituent and solid solubility of Al-6Cu alloy	2
Optimisation of recycled moulding sand composition using the mixture design method	2
Effects of thermal exposure on the microstructure and mechanical properties of Al-12Si-4Cu-1Ni-1Mg-2Mn piston alloys	2
Mechanism of P-wave promoting the solidification feeding in the low-pressure casting of ZL205A alloy	2
Synthesis of Fe₃O₄–aluminium matrix composites: mechanical and corrosion characteristics	2
Influence of silicon content on mechanical properties of IADI obtained from as cast microstructures	2
Characterisation of tensile fracture in squeeze casted Al–Si piston alloy	2
Study on the mechanism of titanium improving the hot ductility of peritectic microalloyed steels in brittle zone III	2
Thermodynamic behaviour of nitrogen in the carbon saturated Fe-Mn-Si alloy during casting	2
Hot tearing and mechanical properties of high electrical and thermal conductivity Al-Fe-Mg-Si-Ni Alloys	1
Solidification Path Calculation of ternary Al-Cu-Mg alloys in Al rich corner	1
New insight of Ca element refining grain structure in commercial purity Mg based on the first-principle calculation	1
Mechanism of Zr poisoning Al-5Ti-B grain refiners based on the first-principles calculation	1
Design and optimisation of die casting process for heavy-duty automatic transmission oil circuit board	1
MODELLING AND VALIDATION OF EFFECT OF BINDER TYPE ON FEEDING BEHAVIOUR OF SPHEROIDAL GRAPHITE CAST IRON	1
Tribological performance Optimization of Al2024-TiB₂composites using Grey-Taguchi approach	1
In-house design of forced convection direct chill casting simulator for casting immiscible Al-Sn alloys	1
Experimental study of MQL applicability in ADI grinding and its influence on surface topography	1
Mechanical and tribological properties of ceramic–aluminium composites developed using stirring-assisted squeeze casting	1
Role of Cerium on the creep properties of the Mg-Sn-Al based alloys	1
Development of ultra-high strength carbide-free bainitic cast steels	1
A new ductile iron for mechanically and thermally strained rolls Part 2: material development varying Ni, Mo, Cr content using DoE	1
Short-process thixoforming of nano-particles reinforced aluminium matrix composites with a high solid fraction	1
High temperature microstructure and mechanical properties of as-cast medium Mn steel with V addition	1
Activity of strontium in liquid Sr-modified Al-7Si alloy	1
Development of cast aluminium alloys for plastic moulding	1