OOIR: Observatory of International Research

Papers

(The H4-Index of Metallurgical and Materials Transactions A-Physical Metallurgy and Mat is 25. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-11-01 to 2024-11-01.)

Article	Citations
Nanoparticles Enabled Mechanism for Hot Cracking Elimination in Aluminum Alloys	72
Introduction to Heterostructured Materials: A Fast Emerging Field	65
Development and Evaluation of Dissimilar Gas Tungsten Arc-Welded Joint of P92 Steel/Inconel 617 Alloy for Advanced Ultra-Supercritical Boiler Applications	54
Microstructure, Properties, and Metallurgical Defects of an Equimolar CoCrNi Medium Entropy Alloy Additively Manufactured by Selective Laser Melting	49
Fracture Resistance of Advanced High-Strength Steel Sheets for Automotive Applications	43
Local Composition Migration Induced Microstructural Evolution and Mechanical Properties of Non-equiatomic Fe40Cr25Ni15 Al15Co5 Medium-Entropy Alloy	42
A Review of Liquid Metal Embrittlement: Cracking Open the Disparate Mechanisms	42
On the Influence of Alloy Composition on the Additive Manufacturability of Ni-Based Superalloys	40
The Role of HAZ Softening on Cross-Tension Mechanical Performance of Martensitic Advanced High Strength Steel Resistance Spot Welds	40
Influence of Specimen Layout on 17-4PH (AISI 630) Alloys Fabricated by Low-Cost Additive Manufacturing	39
Machine Learning Approach to Design High Entropy Alloys with Heterogeneous Grain Structures	36
Microstructure and Texture Evolution in a Post-dynamic Recrystallized Titanium During Annealing, Monotonic and Cyclic Loading	35
Investigation of Solidification and Precipitation Behavior of Si-Modified 7075 Aluminum Alloy Fabricated by Laser-Based Powder Bed Fusion	34
Anomalous Tension Twinning Activity in Extruded Mg Sheet During Hard-Orientation Loading at Room Temperature	31
The Evolution of Oxygen-Based Inclusions in an Additively Manufactured Super-Duplex Stainless Steel	30
Quantitative Investigation on the Slip/Twinning Activity and Cracking Behavior During Low-Cycle Fatigue of an Extruded Mg-3Y Sheet	29
Use of Alloying to Effect an Equiaxed Microstructure in Additive Manufacturing and Subsequent Heat Treatment of High-Strength Titanium Alloys	29
Effect of Silane-Functionalized RuO2 Nanoparticles on the Anticorrosive and Mechanical Properties of Poly (Methyl Methacrylate) Coatings	29
Selective Laser Melting of Maraging Steels Using Recycled Powders: A Comprehensive Microstructural and Mechanical Investigation	29
Effect of Ta Addition on the Microstructure and Tensile Properties of a Ni-Co Base Superalloy	28
Strain Rate Dependent Ductility and Strain Hardening in Q&P Steels	28
Prediction of Mechanical Properties of Wrought Aluminium Alloys Using Feature Engineering Assisted Machine Learning Approach	27
Effects of Yttrium Content on the Three-Dimensional Compressive Creep Anisotropy of Mg-Y Alloys	27
Directional Solidification of a Nickel-Based Superalloy Product Structure Fabricated on Stainless Steel Substrate by Electron Beam Additive Manufacturing	26
Size Control of In Situ Synthesized TiB2 Particles in Molten Aluminum	26

Grain Refinement Mechanisms in Gradient Nanostructured AZ31B Mg Alloy Prepared via Rotary Swaging	25
Improvement of Impact Toughness of the Welding Heat-Affected Zone in High-Strength Low-Alloy Steels through Ca Deoxidation	25
Microstructural Evolution, Mechanical Properties, and Biodegradability of a Gd-Containing Mg-Zn Alloy	25
Investigation on Slip Activity and Plastic Heterogeneity of Aged Mg–10Y Sheets During Compression	25
Novel Approach of Electroshock Treatment for Defect Repair in Near-β Titanium Alloy Manufactured via Directed Energy Deposition	25