Journal of Materials Engineering and Performance

Article	Citations
Enhancing Erosion Behavior of 304SS Treated by Ultrasonic Surface Rolling Extrusion Technique	111
Increasing the Formability of CP-Ti during Incremental Sheet Forming with an Auxiliary Sheet	94
Evaluation of Coefficient of Friction and Investigation into the Effect of Friction and Lubrication on Formability of Ultra-thin Sheets	87
Corrosion of 1.4016 Ferritic Steel by Urea at High Temperature	73
Dynamics of Microbubbles Induced by Thermal Shock in Inconel 718 Pulsed Laser Spot Welding and Formation of Micropores after Solidification in Molten Pool	73
The Microstructure and Mechanical Properties of Welded Joints of Hot-Rolled and Post-Weld Solution-Treated Fe-12.5Mn-9.8Al-1.0C Low-Density Steel	63
Analysis of the Anti-corrosion Performance of Dodecyl Benzene Sulfonic Acid Sodium Salt on Various Heat-Treated Dual-Phase EN8 Steel in an Acidic Environment	61
Influence of Process Parameters and its Optimization on Wear Behavior of an Exceptional Aegle Marmelos Polymer/Aluminum Composite	61
Constitutive Relationship Study of Laves Phase NbCr2/Nb Two-Phase Alloy Using Modified J-C Model and Back Propagation Neural Network Model	55
Phase Evolution at the Interface between Liquid Solder Sn-Zn-Ag and Cu Substrate Studied by In Situ Heating Scanning Transmission Electron Microscopy	51
Influencing Mechanism of Groove Configurations on Microstructure and Tensile Property of Laser Welding-Brazing Al/Steel Joints	49
Influence of Soaking Time and Loading Rate on Semi-solid Compression of Porous Al-4Cu-Mg Alloy	49
Mechanical, Tribological, and Anti-corrosion Properties of Nitrogen-Doped AlCrNbSiTiMoW High-Entropy Coatings	47
A Preliminary Study on the Effects of Aging Temperature on the Microstructure and Mechanical Properties of As-Extruded Mg-12Gd-4Y-1Zn Magnesium Alloy	47
Investigating the Influence of Li and Sc Addition on the Microstructure and Electrochemical Properties of 7075 Aluminum-Based Alloys	47
Microstructure and Mechanical Properties of Explosive Bonded Ti/Steel Plates Processed by Single-Pass Large Strain Rolling	45
Development of an Alternative Heat Treatment to the Traditional T6 Heat Treatment of AlSi10Mg Alloy Produced by Additive Manufacturing	44
Hybrid Strengthening Effect Induced by Dual Deformation in Weakened-Texture Mg Alloy	42
Fatigue Properties of Quenching and Partitioning 980 Steel Laser Welding Joint Obtained under Rapid Cooling Condition	41
Investigations of Tungsten Inert Gas and Metal Active Gas Joints of SUS301L Stainless Steel: Electron Backscatter Diffraction Characterization and Fatigue Performance	41
Effect of SiC on Microstructure and Mechanical Properties of Nano-SiC/Mg-8Al-1Sn Composites	40
Correction to: Post-processing of Wire Arc Additive Manufactured Stainless Steel 308L to Enhance Compression and Corrosion Behavior using Laser Shock Peening Process	38
Effects of Alloying Elements (Ti and Cr) on the Microstructures, Mechanical and Wear Properties of Manganese Brasses	37
Fabricating Efficient and Biocompatible Filament for Material Extrusion-Based Low-Cost Additive Manufacturing: A Case Study with Steel	36
Influence of Ceramic Freeze-Casting Temperature on the Anisotropic Thermal Expansion Behavior of Corresponding Interpenetrating Metal/Ceramic Composites	36

Unraveling the Microstructure and Non-uniform Plastic Deformation Behavior of TC4 Titanium Alloy Produced through Laser Deposition	34
Fabrication of WC-Al2O3 Composite by Reactive Spark Plasma Sintering of WO3, C, and Al	34
Environment-Friendly and Low Toxicity Polishing Solution Preparation and Performance Testing for Medical Titanium Alloy Materials	33
Effects of Cr and Ta Additions on Immersion Corrosion and Electrochemical Behaviors of Laser Cladded Fe90-6%Al2O3 Coating	33
Microstructure Effects on Mechanical Properties of FeNiCrCoCu Nanoporous High-Entropy Alloy with Bicontinuous Characteristics	32
Mechanical Properties and Microstructure of Conical Joints for Dissimilar Steels Continuous Drive Friction Welding	32
Effect of Equiatomic Ti/Zr Substitution on the Shape Memory Effect of Biomedical Ti-Zr-Mn-Mo Alloys	32
Hot Workability and Microstructural Evolution of Powder Metallurgy Ti-22Al-24Nb-0.5Mo Alloy during Hot Compression	31
Effect of Electropulsing Cyclic Baking Process on Microstructure and Mechanical Properties during Hot Compression for 7050 Aluminum Alloy	31
Significantly Enhanced Strength of a Drawn Twinning-Induced Plasticity Steel Wire and its Deformation Twinning Dependency	30
Investigation on the Development of Custom Foot Insole Using Soft Polylactic Acid by Fused Deposition Modelling Technique	30
Influence of Extrusion Process on the Microstructure and Properties of Semi-Continuous Induction Melted TA17 Titanium Alloy Ingot	29
Effect of Laser Power on Porosity and Cracks of Al/Cu Joint	29
Mechanical Properties and In Vitro Corrosion of Biodegradable Open-Cell Zn Alloy Foams	29
Au-Ion and Proton Irradiation-Induced Damage and Hardening in Face-Centered Cubic FeCr Alloy	29
Nickel–Manganese Alloy Coatings via Electrodeposition: Structural and Corrosion Resistance	29
The Effect of Anodic Dissolution on Stress Relaxation in Metals Using Magnesium Alloys and Steel as Examples: A Review	29
The Effect of Titanium Addition on Microstructure and Mechanical Properties of CoCrMo Cast Alloys	29
Fatigue Characteristics and Modeling of Lead–Stainless Steel Composite Entangled Metallic Wire Material	28
Construction of the Constitutive Model and Austenite Recrystallization Model of 100CrMo7-3 Bearing Steel for Wind Power Gearbox	27
Effect of Solution-Aging Treatment on Microstructure, Mechanical Properties, and Corrosion Resistance of Laser Powder Bed Fusion-Fabricated Maraging Steel 300 Part: Importance of the Aging Duration	27
Mechanical, Wear, and Low-Velocity Impact Studies of AL7075/Basalt/Mica Particle Hybrid Metal Matrix Composite through Stir Casting Route	27
Understanding the Formation Mechanism of Al-Rich Interfacial Layer during Galvanizing of Cu Pre-coated High-Strength Steel Sheet	27
Microstructure and Mechanical Behaviors of Electron-Beam Melted Ta10W Alloy at High Temperatures	27
Miedema Model and Srikanth Equation for Predicting the Effect of Microalloying Element on the Microstructure of Cu-Ni-Sn Alloy	27
Development of Cu-(Gr + W) Hybrid Surface Composites Fabricated through Friction Stir Processing	27
Tribological Properties of Diamond-Like Carbon, TiAlN, and Diamond-Like Carbon/TiAlN Coatings Deposited on Carburized 18CrNi4A Steel for Heavy-Duty Aerospace Transmission Components	26
Contribution of Synthetic Fibers to the Strength and Mineralogy of Lime and Cement Stabilized Soils	26
Surface Integrity, Tool Wear, and Chip Morphology Studies in Spot Cooled Vibration Assisted Turning of Ti6Al4V Alloy	26
Corrosion Resistance of Zinc-Doped Hydroxyapatite Coating on Titanium Substrate using Plasma Electrolytic Oxidation for Biomedical Applications	25
Microstructural and Mechanical Evaluation of Pure Copper Rods Processed by Severe Plastic Deformation Method of Hydrostatic Cyclic Extrusion Compression	25
Correction: Performance Evaluation of Various Tool Materials and Electrical Discharge Machining Parameters for Fabrication of Large-Area Micro-textured Surfaces	24
Study on the Softening Regulation of Al-Mg-Si-Cu Alloy Metal Inert Gas Welded Joints	24
Study of the Mechanical Properties and Metallurgical Behavior of Nickel-Based Coatings: Atmospheric Plasma Spraying and Plasma Spray Melting	24
Synchronously Strengthening and Toughening the Binder Jet Additive Manufactured 17-4PH Stainless Steel Based on the Solution and Aging Heat Treatment	24
Machine Learning-Based Prediction of Weld Pool Features in Laser-Arc Hybrid Welding of Ultra-High-Strength Wear-Resistant Steels	24
On the Design, Development, and Calibration of a 3D-Printed Implantable Diaphragmatic Hernia Sensor for Livestock	23
Microstructure-Engineered CoCrFeNiTi HEA Coatings via HLC: Synergistic Enhancement of Wear and Corrosion Resistance	23
Gradient Wire and Arc Additive Remanufacturing of 5CrNiMo Hot Forging Die: Microstructure, Mechanical Properties, and Applications	23
Simulation and Experimental Investigation of Cu-3Ti-3Ni Alloy with Addition of Yttrium	23
Optimizing Heat Treatment to Reduce Failure Rates in Cu-P-Ag Brazing Alloys: A Microstructural, Mechanical, and Corrosion Study	23
Optimization of Hot Backward Extrusion Process Parameters for Seamless Tube of Mg-8Gd-3Y Alloy by Finite Element Simulation	23
Thermoplasticity Control of Fe-Cr-Mn-Al Duplex Stainless Steel: The Study on Composition Design, the Hot-Rolling Process, and Microstructure Co-Evolution	23
Influence of Warm Rolling Temperature on the Microstructure and Mechanical Properties of Fe-32Mn-9.5Al-0.9C-0.11Nb Low-Density Steel	23
Green Electronics Soldering by Application of Third Generation Lead-Free Solder Alloys: Studies on Their Wettability and Interface Microstructure Formed with Copper	22
Multi-response Optimization of Tribological Characteristics for Graphene-Gear Oil Nanolubricants Using Grey-Taguchi Methodology Followed by Scrutinization of Lubrication Mechanisms	22
Optimization of Planar Flow Melt Spinning Process for Producing Thin, Wide, and Continuous Amorphous Ribbons of Fe73.5Si13.5B9Nb3Cu1 Alloys	22
Effect of Hydrogen Content and Microstructure Inhomogeneity on Fatigue Crack Growth Behavior of Ti-0.3Mo-0.8Ni Alloy Argon-Arc Welded Joints	22
Large-Scale Fabrication of High β-Phase PVDF Films with Enhanced Piezoelectric and Electrode Formation Properties	22
Sustainable Reinforcement of PLA Composites with Waste Beech Sawdust for Enhanced 3D-Printing Performance	22

Effect of Secondary Aging on Microstructure and Properties of Spray Formed Al-12.3Zn-2.2Mg-1.5Cu Alloy	21
Electrochemistry-Informed Surface Engineering by Ultrasonic Burnishing for Improved Corrosion Resistance in AZ91D Mg Alloy	21
Influence of Tungsten Electrode Heights on Microstructure and Mechanical Properties of TIG-Welded 5083 Al Alloy via a Process Optimization by Response Surface Methodology	21
Ultrasonic Vibration-Assisted Intrinsic Modeling and Tissue Evolution of 7075 Aluminum Alloy	21
Anisotropic Mechanical Behavior and Microstructural Characteristics of AA2099-T83 Alloy Sheet: Experiment and Simulation	21
Machine Learning Prediction and Optimization of Cold Metal Transfer Welding Parameters for Enhancing the Mechanical and Microstructural Properties of Austenitic-Ferritic Stainless-Steel Joints	21
Metallurgical and Mechanical Characteristics of AA2014-T6 Alloy Cladding over Mild-Steel IS2062 Substrate through Friction-Stir-Surfacing Process	21
Effect of Laser Cladding TiC on Microstructure and Mechanical Properties of TC4|C/C Bonded Joint	20
High-Frequency Electromagnetic Properties of Injection Molded Soft Magnetic Composites	20
Process Optimization and Mechanical Characterization of SiC-Reinforced Friction Stir Welded AZ91D/AA6061-T6 Joints Using Response Surface Methodology	20
Development of High Strength Fire-Resistant Earthquake Steel	20
Corrosion Resistance of Plain and Ribbed Steel Bars Coated with Quartz Sand-Modified Enamel in Simulated Concrete Pore Solutions	20
Study on Microstructure and Tribological Behavior of Additively Manufactured Graphene/AlSi10Mg Composite	20
Effect of CeO2 Doping on Thermal Shock Resistance of Y2O3-Stabilized ZrO2 Thermal Barrier Coatings	20
Measurement of Residual Stress of Metal Materials Based on Ultrasonic Detection Method	20
Microstructure and Mechanical Behavior of Low-Carbon Microalloyed Steel with a Mixed Gradient Structure	19
Effect of Tube Arrangement on the Welding of the Tube-to-Tubesheet Joint of Shell-and-Tube Heat Exchangers Using the Finite Element Method	19
Effect of Multi-layer and Multi-pass Welding on the Microstructure and Properties of V-N-Cr Weathering Steel	19
Thermo-Mechanical Investigation on Hot Deformation Behavior of Cast Magnesium–Aluminum Alloy: Experimental and Constitutive Analysis	19
Retraction Note: Minimization of Surface Roughness and Residual Stress in Grinding Operations of Inconel 718	19
Comparative Analysis of Fatigue Strength and Life of Vascular Stents under Various Deformation Behaviors	19
Analysis of Hot Forging of a Bainitic Steel Hardened by Continuous Cooling Using Wedge Test	19
Microstructural and Nanomechanical Characterization of Multistep Hot Cross Rolled AA7075 and AA7075/SiC/Gr Composite	19
Effects of Heat Treatment on the Mechanical Properties of Fe-Based ER70S-6 Cladding on Aluminum Substrate Using Cold Metal Transfer Process	19
Characterization and Modeling of Wear Behavior of AISI D3 Tool Steel under Dry Sliding Conditions	19
Study on Creep Behavior of Nitrogen-Containing Nickel-based Deposited Metal at 565 °C	19
Effect of Interlayer Dwell Time on Microstructure and Properties of ER2209 Duplex Stainless Steel Fabricated by Plasma Arc Additive Manufacturing	19
Filler Effects on Heat-Affected Zone Liquation Cracking in Rotationally Repaired Inconel 738LC Tungsten Inert Gas Welds: An Industrial Perspective	18
Hardness Prediction of NbTaW-Based High-Entropy Alloys with Machine Learning	18
Effect of Sintering Temperature on Microstructure, Mechanical, and Tribological Behavior of Aluminum-Based Composites Containing Double-Layered Al/CuFe Core-Shell Particulates	18
Enhanced Molten Sulfate Corrosion Resistance of CoCrNiAlY-Yttria-Stabilized Zirconia-LaMgAl11O19 Dual Ceramic Coating via an Al Plating Layer	18
Influence of Fusion Zone Metallurgy on the Mechanical Behavior of Ni-Based Superalloy and Austenitic Stainless Steel Dissimilar Joint	18
Response and Deformation Behavior of Cu-Pb-Sn Alloys with Different Microstructures to U-Type Die Bending Loads	18
Corrosion Behavior of 2507 Super Duplex Stainless Steel in H2S-Free and H2S-Containing Acidic Environments	18
The Enhanced Corrosion Resistance of Harmonic Structured Cantor Alloy in Hank’s Simulated Body Fluid	18
Effects of Li Content on Phase Evolution and Mechanical Properties of Mg-xLi-6Zn-1.5Y Alloy	18
Effect of Sn on Grain Boundary Character Distribution in Austenitic Stainless Steel 316L	18
Evaluation of Compression, Wear and Electrochemical Behavior of CoCrMo Alloy Samples Fabricated with Direct Metal Laser Sintering	18
Effect of Ni/Al Ratio on Solidification Structure and Properties of NiAl-Based Multi-principal Element Alloy	18
Effect of B4C Content on the Microstructure and Corrosion Properties of In-Situ Reinforced Ti-6Al-4 V Coatings by Laser Directed Energy Deposition Technology	18
The Effect of Ti Content on the Wear Resistance of Fe-Cr-C Flux-Cored Welding Wire	17
Effect of Heat Treatments on the Strain Hardening Behavior of AISI 1045 and 304 Steels	17
Investigation of the Corrosion Resistance of Ti-Reinforced 0.7 wt.% Cr Weathering Steel in an Industrial Atmospheric Environment	17
Effects of Fabrication Process on Microstructure and Properties of Al2O3P/CrCoNi Medium-Entropy Alloy Matrix Composites	17
Influence of B4C Content on the Properties and Microstructure of CoCrFeNiSi High-Entropy Alloy Coatings by Plasma Cladding	17
Structural and Comprehensive Performance of CoCrFeMnNi High-Entropy Alloys via Fast Hot-Pressed Sintering: Effect of Sintering Temperature	17
Research on Strengthening Mechanisms of High-Nitrogen Austenitic Stainless Steel	17
Investigation of Microstructure, Mechanical, and Wear Behavior of Lanthanum Zirconate, Yttrium Zirconate, and Lanthanum Yttrium Zirconate	17
Influence of Tool Size and Step Depth on the Formability Behavior of AA1050, AA6061-T6, and AA7075-T6 by Single-Point Incremental Forming Process	17
Effect of Cryogenic Treatment on 7A09 Aluminum Alloy and Optimization of Process Parameters	17
Characteristics and Tribological Properties of a Thick Self-Lubricating Mg(OH)2 Layer on Mg Substrate	17
Residual Stresses in a Novel Dual-Phase Ti-6.5Mo-2.5Cr-2V-2Nb-1Sn-1Zr-4Al Alloy	17
Study on the Impact of Dual-Stage Heat Treatment on Residual Stress and Fatigue Life of Severely Plastic Deformed Ti6Al4V Titanium Alloy	17
Coupling Effect of Ultrasonic Assistance and Zn Interlayer on the Performance of Dissimilar Al/Mg Friction Stir Lap Welds	17
On the Mechanical Strain Tunability of Powder Bed Fusion-Laser Beam-Based Functional Parts Using Virgin and Thermally Conditioned Primary Recycled 17-4 Precipitate Hardened Stainless Steel	17
Comparative Study on the Microstructure, Wear Behavior, and Corrosion Performance of Iron-Based and Cobalt-Based Coatings Fabricated by Laser Cladding	17
Hot Deformation Behavior and Processing Map of Al-Zn-Mg-Cu-Zr Alloy	17
Correction: Dynamic Mechanical Behavior and Microplastic Deformation Mechanism of AM50A Magnesium Alloy under High-Speed Impact	17
Study on Microstructure Uniformity of Ti-6Al-4V through Electron Beam Additive Manufacturing	17
Integrated Optimization and Multiscale Characterization of AA2024-T351/MWCNTs Surface Composites via Friction Stir Processing	17
Anti-Corrosion Properties of Array-Structured Superhydrophobic Surfaces	17
Optimization of Resin Printing Parameters for Improved Surface Roughness Using Metaheuristic Algorithms: A Multifaceted Approach	17
Additive Manufacturing of Compliant Mechanisms for Deployable Aerospace Structures	17
Influence of Chitosan Concentration and Post-deposition Heat Treatment on Hydroxyapatite-Chitosan Coatings Produced by Electrophoretic Deposition on Ti-6Al-4V for Biomedical Applications	17
Effect of Hot Rolling on Microstructure and Mechanical Properties of WE43 Rare-Earth Magnesium Alloy	17
Optimization of FSW Parameters Using SA Algorithm and ANFIS-Based Models to Maximize Mechanical Properties of AZ80A Mg Alloy Joints	17
Performance Evaluation and Parametric Optimization of Turning Operation of Ti6Al-4V Alloy Under Dry and Minimum Quantity Lubrication Cutting Environments	16
Effect of Fused Filament Fabrication Parameters and Tetrabromobisphenol-A/Microcrystalline Cellulose Additives on the Dynamic Mechanical Behavior of Polycarbonate/Acrylonitrile–Butadiene–Styrene Blend	16
Microstructure Evolution and Damping Performance Response of Cold-Rolled Fe-Mn-Based Alloys	16
Effect of Ni Content and Brazing Treatment on the Microstructure and Mechanical Properties of Al-Mn-Ni Aluminum Alloy	16
Life Cycle and Machinability Analysis of Milling Incoloy 286 Using Sustainable Cooling/Lubrication Technologies	16
Effect of Microstructural Evolution on Creep and Rupture Behavior of Inconel 617 Alloy	16
Microstructural Evolution and Mechanical Properties of AZ31 Magnesium Alloy Processed through Constrained Groove Pressing at Different Deformations and Temperatures	16
Ternary Element Effects of Nb and V Additives on the Low-Temperature Wear Behavior of NiTi-Based Shape Memory Alloys	16
Effect of Aging on Corrosion Resistance of AZ31 Magnesium Alloy	16
Effect of Oxidative Atmosphere on Laser Welding Properties of Galvanized High-Strength Steel	16
Hot Forging of Induction Sintered Ti-46Al-1B (at.%) Alloy Synthesized via Powder Metallurgy Route	16
Microstructure Evolution and Mechanical Behavior of AZ31 Magnesium Alloy Sheet with Bimodal Texture under Bending Deformation	16
Tribological Investigation of La2O3 Dispersed W-Ni-Cu Heavy Alloy Processed through Powder Metallurgy Process	16
Comparison of Modified Arrhenius, Modified Zerilli–Armstrong, and Long Short-Term Memory Models for Predicting Hot Deformation Behavior of NiAlCrFeMo High-Entropy Alloy	16

Microstructure and Mechanical Properties of 6082 Aluminum Alloy Automotive Flange Parts Produced by Squeeze Casting	16
Effects of Sintering Temperature on the Performance of ZrB2-ZrC Ceramics Prepared by In-Situ Reactive Spark Plasma Sintering	16
Study on Microstructure and Properties of Ni/C Layer by Ultrasonic-Assisted Laser Cladding	16
Investigation of Fireside Corrosion of Nickel-Based Superalloy 617M for Advanced Ultra Super Critical Coal Fired Boiler Plants	16
Research on Full-Cycle Modeling of High-velocity Oxygen-Fuel Spraying Nano-WC on AZ31B Magnesium Alloy	15
Comparison of Dry Sliding Tribological Behavior of Lean Duplex Stainless Steel and Standard Austenitic Stainless Steel	15
Prediction and Optimization of Weld Bead Geometry in Automated Build-Up Welding Using Back-Propagation Neural Networks	15
Investigations on Energy Absorption Behavior of Laser Powder Bed Fusion-Based 2D and 3D Multi-layered Sandwich Lattice Structures	15
Dry Sliding Tribological Performance of AA6061 Hybrid Nanocomposites Reinforced with Self-Lubricating GNP and Load-Bearing Y2O3 Fabricated by Stir–Squeeze Casting	15
Bioinspired Multiscale Layers Constructed via Laser Alloying and Bacillus Subtilis-Induced Mineralization for Marine Corrosion Protection	15
The Effect of Processing Environment on the Microstructure, Texture, and Sacrificial Anodic Performance of Mg-1Er-1Pr Alloy Processed by Friction Stir Processing	15
Tolerability of Fe35Ni35Cr20Mn10 Multi-principal-component Alloy to Impurity Elements	15
Effect of Aging Treatment on Microstructure and Properties of As-Rolled Al-8.2Zn-2.0Mg-2.3Cu Alloy	15
Multi-objective Optimization for Ice-Assisted Drilling of Ti-6Al-4V Alloy Thin-Walled Parts	15
Multi-Factor Coupling Corrosion Mechanisms and Protective Strategies of Chinese Railway Freight Cars	15
A Study on Phase Evolutions and Tensile-Shear Performance of Dissimilar Resistance Spot Welds Formed Between AISI 430 Ferritic Stainless Steel and AISI 321 Austenitic Stainless Steel	15
Investigations on Precipitation Behavior and Performance of High-Strength Aluminum Alloy under Simulated Hot Form and Quench Conditions	15
Integrated Experimental Study on Thickness Uniformity, Thinning Limit, and Forming Force in Heat-Assisted Single-Point Incremental Forming of AA1050 Aluminum Alloy	15
On Compressive Properties of 3D-Printed High-Density Polyethylene–Stubble Waste Composite Tiles	15
Effect of Laser Shock Peening on the Stresses and Tensile Properties of Welded Joints Made of 7075 Aluminum Alloy for Folded Chairs	15
Deep Learning Approach for Damage Detection on Composite Structures	15
Effect of Nb on the Hot Deformation Behavior and Martensitic Crystallographic Characteristics of HSLA Steel	15
Study on the Micro-cutting Mechanism of 7075 Aluminum Alloy with Pre-fabricated Surface Microtextures	15
Numerical and Experimental Study on the Deposition Mechanisms of Plasma Spraying on 7075 Aluminum Alloy	15
Research on the Hot Deformation Behavior and 3-D Hot Processing Maps of Ti-6Al-4V Titanium Alloy	15
Flow Stress Modeling of Tube and Slab Route Sheets of Zircaloy-4 Using Machine Learning Techniques and Arrhenius Type Constitutive Equations	15
Effect of Laser-Arc Heat Input Ratio on the Formation, Microstructure, and Properties of EH36 Steel with Laser-Metal Inert Gas Hybrid Welding	15
Numerical Modeling and Damage Prediction of 7075-T6 Aluminum Alloy Using an Improved Lemaitre Model	15
Corrosion Characterization of In Situ Nitrogen Reinforced Titanium Alloy Arc Cladding Layer	14
Impact of Process Parameters on the Strength and Integrity of FSW Low-Carbon Steel Joints	14
Study of Ballistic Impact Performance of the Bioinspired Flexible Multilayered Filling Armor by Different Projectiles	14
Effects of Cryogenic Temperature on Adiabatic Shear Localization in Equiatomic NiCrFe Medium-Entropy Alloy	14
Quantitative Analysis of Codeformation Behavior of Ceramic and Metallic Particle System	14
Effect of Intercritical Temperature on the Microstructure and Mechanical Properties of 10CrMnMoSi Dual-phase Steel	14
Al2O3-Reinforced TiB2-Fe Composites: Microstructural and Mechanical Properties	14
Influence of β Precipitated Phase on Mechanical Properties of Equal Channel Angular Pressing-Processed WE43 Alloy	14
Controlled Electrodeposition of Silver on Implant-Grade Ti-6Al-4 V ELI Alloy: Surface and Corrosion Behavior	14
Infrared Pulsed Picosecond Laser-Induced Plasma-Assisted Ablation of Micro-textures on Quartz Surface	14
Refurbishment of Continuous Caster Rolls by Laser Cladded Fe-Cr-Ni-Mo-Co Alloy	14
Machine Learning-Based Temperature-Induced Phase Transformation Temperature Prediction of Ti-Based High-Temperature Shape Memory Alloy	14
Resistance Spot Welding (RSW) of Dual-Phase (DP590) Steel	14
Structural Optimization of Hot Forging Dies and Improved Wear Resistance of Gear Teeth	14
Effect of Stress Concentration on the Tensile Deformation of AZ31 Magnesium Sheets with Perforated Cylindrical Voids of Various Shapes and Sizes	14
3D-Printed Sandwiched Acrylonitrile Butadiene Styrene/Carbon Fiber Composites: Investigating Mechanical, Morphological, and Fractural Properties	14
Residual Stress, Adhesion, Hardness, and Corrosion Resistance of Surface Alloyed Layer Formed during Sand Casting of Mild Steel	14
Hot Deformation Behavior and Hot Rolling Simulation of a New FeCrMo Alloy for Piston Rings	14
On Development and Characterization of Functionally Graded Material with Minor to Considerable Melting Temperature Variation Processed by Laser Powder Bed Fusion	14
Hardening and Strengthening Effects Induced by Incorporation of Titanium in Hexagonal Boron Nitride Ceramics	14
Development of EN AW-6082 Metal Foams and Stochastic Foam Modeling for the Individualization of Extruded Profiles	14
Insight into Microstructure Evolution and Oxygen Permeation of Pitch-based Carbon Fiber in the Stabilization Process	14
High Strain Rate Compression Response of Kevlar and Interyarn Hybrid Carbon-Kevlar Polymer Composites	14
The Effect of Heat Treatment Parameters on the Mechanical and Microstructural Properties of an ASTM A860 WPHY 65 Pipe Fitting: An Experimental Investigation	14
Effect of Build Orientation on the Electrochemical Behavior of Additively Manufactured Ti-6Al-4V Alloy	14
Al/Steel Tubular Bimetallic Structure Fabricated by Rotary Wire Arc Surfacing	14
Annealing of Electrodeposited Nickel Coatings on Aluminum Alloy: Microstructural Properties and Wear Resistance of Nickel-Rich Aluminide Layers	14
Brazing Mechanism of 70% SiCp/Al Composites with Ti Foam/AlSiMg Filler Metal	14
Microstructure and Mechanical Properties of Hypereutectic Al-Si Alloys Subjected to Magnetodynamic Treatment	14
Enhancing Wear Resistance and Deposition Efficiency in Low-Pressure Cold Spray Coatings through Toolpath Optimization	14
Effects of Fused Deposition Modeling Process Parameters Infill Pattern, Layer Thickness, and Printing Temperature on the Tensile Properties and Surface Roughness of 3D-Printed Polylactic Acid	14
Hybrid Welding Process in Lieu of Conventional Practices for Fabrication of Austenitic Stainless Steel AISI 304L Components in Nuclear Facility	14
Graphene Reinforced Binary Resin-Based Carbon Foam Composites for Mechanical and Electromagnetic Interference Shielding Applications	14
Optimizing the Corrosion Resistance of Ni-Containing Low-Alloy Steels with Mo Addition in Tropical Marine Atmosphere	14
Microstructure and Performance Analysis of ZTA-Reinforced Modified High-Chromium Cast Iron for Roller Sleeves	14
Investigating Wear Characteristics of Inconel 625 and VC-Based Claddings on EN8 Steel Developed by WAAM	13
Effects of Tellurium on Inclusions and Machinability of Cr12MoV Die Steel	13
Prediction of Phase Formation Sequence in Multicomponent NiCoW/Nb3Al Interface	13
Studies on High Temperature Wear Behavior of Additively Manufactured Ti-6Al-4V Alloy Using Machine Learning Models	13
Mesoscopic Modeling and Simulation of Microscopic Residual Stress for 8Cr4Mo4V Steel Bearing Ring After Heat Treatment	13
Effect of BN Addition on Microstructure and Properties of Ti-6Al-4V Arc Cladding Layer	13
Effect of Rolling Process on the Corrosion Resistance of Ferritic Stainless Steel	13
Effect of Laser Scanning Speed on the Tribological and Wear Resistance Properties of h-BN/TC4 Composite Coatings	13
Effects of Frictional Loading on Tribological Properties of Laser Cladding Ti2AlC/TC4-Coated TiC Particle-Reinforced Coatings on Ti6Al4V	13
Effect of hBN Content on the Friction and Wear Characteristics of Al2O3-B2O3-CaO-hBN Ceramic Composites under Dry Sliding Condition	13
High- and Medium-Velocity Impact Behavior of Al5083/SiC Interpenetrating Lightweight Composites for Monocoque Armor Panels	13
Effect of Interfacial Behavior on the Performance of Ag/Mn+1AXn (A = Sn, Al, n = 1, 2) Electrical Functional Composites	13
Influence of Titanium on the Microstructure and Wear Properties of Spray-Formed Hypereutectic Al-Si Alloys	13
Structure-Property-Process Parameters Correlation of Laser Shock-Peened Titanium Alloy (Ti6Al4V) Without Protective Layer	13
Balancing Strength and Ductility in AA6061 Aluminum Alloy: Synergistic Effects of Accumulative Roll Bonding Combined with Heat Treatment	13
Incorporation of Agro-industrial Waste Coconut Fiber in Anti-corrosive Coatings as Environmentally Friendly Pigment	13
Influence of Scanning Velocity on a CoCrMoW Alloy Built via Selective Laser Melting: Microstructure, Mechanical, and Tribological Properties	13
Manufacturing of Oxide Dispersion Strengthened Fe-Cr-Al Alloy Using a Nonconventional Extrusion Process	13
Temperature-Dependent Edge Effects and Deformation Mechanisms in Monocrystalline Au Nanoindentation: A Molecular Dynamics Study	13
Influence of Tb4O7 Doping on the Magnetic Characteristics and Corrosion Resistance of Sintered Nd-Fe-B Magnets	13
Hydrogen Embrittlement Resistance of High Strength 9260 Bar Steel Heat Treated by Quenching and Partitioning	13
In-Situ Tensile Fracture Behavior and Interface Microstructures in Ti/Al/Ti Three-Layered Explosive Clad Plate	13
Study on the Effect of Ultrasonic Impact Treatment on the Micro-machinability of HfZrTiTaAl High-Entropy Alloys	13
Effect of Protective Coating Layer and Overlapping Factor on the Microstructure and Mechanical Properties of Rene-80 Ni-Based Superalloy in Laser Shock Peening Process	13
Comparative Analysis of WCu, WC, and BeCu Electrodes Using Taguchi L18 Design for High-Performance EDM of Additively Manufactured AlSi10Mg Lattice Structures	13
Enhanced Wear and Mechanical Properties of Ferrium® C64 Steel via Heat Treatment and ECAP Processing	13
Identification of Forming Limits of CP Titanium Gr 2 Using Electrically Assisted Warm ISF Process	13
Controllable Fabrication of Metallic Chromium Coatings by Electrodeposition in NaCl-CaCl2-CrCl2 Molten Salt	13
Improvement in Impact Resistance of Thermally Sprayed WC-Ni Coating/Steel System	13
Investigation of Water-Based Hybrid Nanofluid on Tribological Performance in Minimum Quantity Lubrication Grinding of Nimonic-90 Superalloy	13
Development of Weighted Ensemble Deep Learning Network for Surface Roughness Prediction and Flank Wear Measurement	13
A Study on Mechanical Properties and Microstructure of Welded Joints in EH40 Steel with High Heat Input Welding	13