OOIR: Observatory of International Research

Papers

(The H4-Index of Journal of Materials Engineering and Performance is 31. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Enhancing Erosion Behavior of 304SS Treated by Ultrasonic Surface Rolling Extrusion Technique	129
Evaluation of Coefficient of Friction and Investigation into the Effect of Friction and Lubrication on Formability of Ultra-thin Sheets	100
Corrosion of 1.4016 Ferritic Steel by Urea at High Temperature	88
Dynamics of Microbubbles Induced by Thermal Shock in Inconel 718 Pulsed Laser Spot Welding and Formation of Micropores after Solidification in Molten Pool	70
The Microstructure and Mechanical Properties of Welded Joints of Hot-Rolled and Post-Weld Solution-Treated Fe-12.5Mn-9.8Al-1.0C Low-Density Steel	64
Analysis of the Anti-corrosion Performance of Dodecyl Benzene Sulfonic Acid Sodium Salt on Various Heat-Treated Dual-Phase EN8 Steel in an Acidic Environment	62
Influence of Process Parameters and its Optimization on Wear Behavior of an Exceptional Aegle Marmelos Polymer/Aluminum Composite	61
Constitutive Relationship Study of Laves Phase NbCr2/Nb Two-Phase Alloy Using Modified J-C Model and Back Propagation Neural Network Model	55
Phase Evolution at the Interface between Liquid Solder Sn-Zn-Ag and Cu Substrate Studied by In Situ Heating Scanning Transmission Electron Microscopy	52
Influence of Soaking Time and Loading Rate on Semi-solid Compression of Porous Al-4Cu-Mg Alloy	52
Influencing Mechanism of Groove Configurations on Microstructure and Tensile Property of Laser Welding-Brazing Al/Steel Joints	51
Investigating the Influence of Li and Sc Addition on the Microstructure and Electrochemical Properties of 7075 Aluminum-Based Alloys	49
A Preliminary Study on the Effects of Aging Temperature on the Microstructure and Mechanical Properties of As-Extruded Mg-12Gd-4Y-1Zn Magnesium Alloy	47
Microstructure and Mechanical Properties of Explosive Bonded Ti/Steel Plates Processed by Single-Pass Large Strain Rolling	43
Mechanical, Tribological, and Anti-corrosion Properties of Nitrogen-Doped AlCrNbSiTiMoW High-Entropy Coatings	43
Development of an Alternative Heat Treatment to the Traditional T6 Heat Treatment of AlSi10Mg Alloy Produced by Additive Manufacturing	42
Hybrid Strengthening Effect Induced by Dual Deformation in Weakened-Texture Mg Alloy	41
Investigations of Tungsten Inert Gas and Metal Active Gas Joints of SUS301L Stainless Steel: Electron Backscatter Diffraction Characterization and Fatigue Performance	40
Fatigue Properties of Quenching and Partitioning 980 Steel Laser Welding Joint Obtained under Rapid Cooling Condition	40
Correction to: Post-processing of Wire Arc Additive Manufactured Stainless Steel 308L to Enhance Compression and Corrosion Behavior using Laser Shock Peening Process	38
Effects of Alloying Elements (Ti and Cr) on the Microstructures, Mechanical and Wear Properties of Manganese Brasses	37
Fabrication of WC-Al2O3 Composite by Reactive Spark Plasma Sintering of WO3, C, and Al	37
Fabricating Efficient and Biocompatible Filament for Material Extrusion-Based Low-Cost Additive Manufacturing: A Case Study with Steel	37
Unraveling the Microstructure and Non-uniform Plastic Deformation Behavior of TC4 Titanium Alloy Produced through Laser Deposition	36
Environment-Friendly and Low Toxicity Polishing Solution Preparation and Performance Testing for Medical Titanium Alloy Materials	35

Effect of Electropulsing Cyclic Baking Process on Microstructure and Mechanical Properties during Hot Compression for 7050 Aluminum Alloy	34
Mechanical Properties and Microstructure of Conical Joints for Dissimilar Steels Continuous Drive Friction Welding	34
The Effect of Anodic Dissolution on Stress Relaxation in Metals Using Magnesium Alloys and Steel as Examples: A Review	33
Mechanical Properties and In Vitro Corrosion of Biodegradable Open-Cell Zn Alloy Foams	32
Effect of Laser Power on Porosity and Cracks of Al/Cu Joint	32
Construction of the Constitutive Model and Austenite Recrystallization Model of 100CrMo7-3 Bearing Steel for Wind Power Gearbox	31
Microstructure and Mechanical Behaviors of Electron-Beam Melted Ta10W Alloy at High Temperatures	31
Miedema Model and Srikanth Equation for Predicting the Effect of Microalloying Element on the Microstructure of Cu-Ni-Sn Alloy	31
Au-Ion and Proton Irradiation-Induced Damage and Hardening in Face-Centered Cubic FeCr Alloy	31