OOIR: Observatory of International Research

Papers

(The H4-Index of Transactions of Nonferrous Metals Society of China is 32. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-06-01 to 2026-06-01.)

Article	Citations
Effect of wire diameter compression ratio on drawing deformation of micro copper wire	97
Mechanical properties and microstructure evolution of solidified copper tailings with hydantoin epoxy resin	87
Cathodic inhibition mechanism of magnesium alloys by using iron-complex inhibitor	77
Effect of pH-dependent bath speciation on cobalt electrodeposition from sulfate−gluconate solutions	76
High-throughput determination of mechanical and diffusion properties of Ti–Ta–Fe alloys	74
Effect of sintering temperature and holding time on structure and properties of Li1.5Ga0.5Ti1.5(PO4)3 electrolyte with fast ionic conductivity	63
Microstructure and mechanical property of bonding zones between Ta foil and steel plate fabricated by explosive welding	60
Ductile fracture behavior of in situ TiB2 particle reinforced 7075 aluminum matrix composite in various stress states	58
Influence mechanism of reduction rate on interface microstructure and mechanical properties of TA1/TC4 composite plate	53
Collaborative optimization method for sintering schedule of ternary cathode materials under microscopic coupling constraints	53
Microstructure, mechanical properties, and corrosion behavior of 6061Al alloy prepared by cold spray-friction stir processing composite additive manufacturing	52
Interface structure and properties of spray-forming (SiCp+β-LiAlSiO4)/6092Al matrix composites	51
Ore-forming environment of Pb−Zn mineralization related to granite porphyry at Huangshaping skarn deposit, Nanling Range, South China	49
Plasma electrolytic oxidation behavior and corrosion resistance of brass in aluminate electrolyte containing NaH2PO4 or Na2SiO3	44
Kinetics and morphological evolution mechanism of WO3 during non-isothermal hydrogen reduction	44
Effect of laser surface melting on microstructure evolution and cavitation behavior of nickel aluminum bronze	44
Improved resistance to creep and underlying mechanisms in TiB/(TA15-Si) composites with network structure	44
Empirical decay relationship between ionic conductivity and porosity of garnet type inorganic solid-state electrolytes	40
Engineering heterogeneous microstructures for enhanced strength and ductility in air-cooled Al−Mg−Si alloys	39
Effects of Cu additions on microstructure and mechanical properties of as-cast CrFeCoNiCu high-entropy alloy	38
Development and characterizations of graded porous titanium scaffolds via selective laser melting for orthopedics applications	37
High-throughput studies and machine learning for design of β titanium alloys with optimum properties	36
Microstructure and corrosion resistance of Zn–Al/T8 superhydrophobic composite coating on sintered NdFeB magnet	35
High-frequent pulsing ablation of C/C−SiC−ZrB2−ZrC composite for different cycles to 2000 times in plasma	34
Effect of alloying element Zr on microstructure and properties of Cu−Y2O3 composites	34

Evolution of precipitates and mechanical properties of T6-treated and thermally exposed WAAM-ZL205A alloy	33
Influence of free-end torsion on compressive behavior of extruded AZ31 rod at various temperatures	33
Simultaneous improvement of strength and ductility in selective laser melted low Sc content Al-Mg-Mn-Sc-Zr alloy via aging treatment	33
First-principles investigation on structural, thermodynamic, and elastic properties of suboxide Zr3O phase	33
Effect of integration of mechanical ball milling and flue gas desulfurization gypsum on dealkalization of bauxite residue	32
Environment-dependent phase stabilities of titanium hydrides: First-principles prediction	32
Damage characteristics of Cu−Cr−Zr alloy rail of electromagnetic railgun after simulated launch	32