OOIR: Observatory of International Research

Papers

(The TQCC of Proceedings of the Institution of Mechanical Engineers Part A-Journal is 3. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Double-hole film cooling on a turbine blade under varying blowing ratios and turbulence intensities: A numerical study	35
Assessment of the Newcomen engine’s development potential as heat engine for low temperature waste heat	28
Influence of runner eccentricity on the hydraulic performance of tubular turbine: A comparative case study	23
Analysis of vortex combustion flow in a chamber o f guide ring coupling with swirl flow	19
Resource adequacy and capacity Procurement: Metrics and decision support analysis	16
Modeling, sensitivity analysis, and multi-objective optimization of a humidification-dehumidification-desalination system	14
Pressure characteristics and identification method of water hammer in single phase and two phases with entrapped air during pump startup	13
Optimization of squirrel-cage induction motor design for EV applications through FEM simulations with ANSYS	12
Performance evaluation of Photovoltaic–Thermal (PVT) systems with different heat transfer fluids: Theoretical modeling and experimental validation	12
Minimizing power loss and enhancing voltage stability in distributed networks using an advanced metaheuristic approach: A case study on IEEE 33- and 69-bus networks	12
Investigation of energy loss characteristics of solid-liquid flow in centrifugal pumps under different flow conditions	12
Wind power forecasting based on a novel time series Dynamic context-aware power forecasting model	11
Innovative heat dissipation solution for air-cooled battery pack using stair-step arrangement	11
Secondary air induced flow structures and their interplay with the temperature field in fixed bed combustors	10
Heat and mass transfer process simulation and structure design of a water-cooled fin solid metal hydride storage system	10
Numerical study of marine high temperature film cooling endwall with particle deposition on mesh morphing	10
Optimization of the design of a heavy-duty gas turbine intake air volute using the surrogate model method	10
Calibration of parameters and predictive control strategy of a wind turbine for improvement of energy harvesting	9
Experimental investigation of evolution characteristics tip flow instability in a centrifugal compressor with a vaneless diffuser	9
Influence of eccentric impeller on pressure pulsation of large-scale vaned-voluted centrifugal pump	8
Characterization of bifacial technology Pv systems	8
Effect of different axial deflected angles of reversed blade-angle slots on the axial flow compressor performance and stability	8
Influence of trailing edge flap length and deflection angle on the performance of the multiphase pump	8
Understanding of the asymmetric twin-stroll radial turbine under steady and pulsating inlet conditions	8
Numerical analysis of the internal biased flow mechanism of the siphon outlet pipe under the action of axial flow pump	8

Experimental investigation on spray and flame characteristics of a marine diesel engine with single and double injection	8
A numerical study on effect of intra and inter spaced winding configuration on performance of oil forced transformer cooling system	8
Thermal performance improvement on winglet tip of a turbine stage under engine condition-part I: Winglet geometry modifications	7
Investigation of suction pressure pulsation prediction of rotary compressor with total variation diminishing scheme and one-dimensional accumulator model	7
Numerical analysis of rim seal flow in gas turbine secondary air systems with hot gas ingestion and vane cooling	7
Comparative exergetic sustainability analysis of subcritical and supercritical organic Rankine cycle plants for a waste heat recovery application	7
The multi-objective optimisation design of outlet guide vanes of diagonal flow fan based on sobol sensitivity analysis	7
Transient thermodynamic and parametric analysis of solar-assisted Rankine cycle	7
Numerical and experimental investigation of 3D unsteady flow fields of a low head axial flow turbine under different blade number	7
Optimizing energy management in renewable hybrid water pumping systems: A sustainability alternative for agricultural irrigation	7
Dynamic coupling effects of injection on spray and mixture formation in an asymmetrically vibrating combustion engine	6
Optimising the thicknesses of porous transport layers of a PEM fuel cell	6
Influence of tip clearance inclination on the performance of axial flow impeller in storage mode	6
Influence of vortex interactions on the exergy transfer and performance of OWC wells turbine	6
Flow characteristics of a centrifugal fan with optimized edge curvatures of an impeller front disk	6
Comparative performance analysis of solar module types in automated solar power plants using multi objective optimization	6
Thermofluid process simulation of wet biomass and ammonia co-firing in an industrial watertube boiler	5
Enhancing thermal and exergy performance of solar air heaters using tea-dust-based activated carbon nanoparticle coatings on V-corrugated absorbers plate	5
Two-stage identification algorithm for battery state of health models	5
Influence of the spanwise grooves on aerodynamic characteristics of the compressor cascade and rotor under different reynolds numbers	5
The self-excited thermoacoustic instability behavior of a premixed hedge combustor with an elbow-connection or T-shape supply system	5
CFD investigation and optimization of heat transfer enhancement and pressure drop in solid, hollow, and perforated pin fins	5
A novel neural network method of aerodynamic performance prediction for wind turbine airfoils under glaze ice conditions	5
Impact of non-uniform incoming flow from intermediate cooling systems on second-stage centrifugal compressors: Insights from three-dimensional spatiotemporal coupled simulation	5
Causality analysis of meteorologically sensitive in offshore wind power generation based on the time-lagged convergent cross mapping	5
ANFIS-based predictive control for photovoltaic systems under partial shading conditions	5
Numerical investigations of mass-flux redistribution and performance prediction model on coupling effects of total pressure distortion-low Reynolds number in axial compressor	5
Study on energy conversion characteristics and pressure fluctuation interference characteristics between two stage impellers of the pump as turbine	5
Influence of jumping-droplet condensation on the properties of separated flow in an air-cooled condenser tube: An Euler-Lagrange approach	5
Prediction of the remaining useful life of lithium-ion battery based on particle filter-long short term memory network	5
Effect of inlet geometric distortion on the aerodynamic performance of a multistage compressor	5
Study on fluid flow as well as heat transfer characteristics of high-speed solid-rotor motor cooled by natural gas based on turbulent Taylor-Couette vortex	5
Optimal design of the blunt trailing-edge wind wheel with a bionic V-riblets structure for H-type vertical axis wind turbines	5
Robust estimation of lithium-ion battery state of health based on electro-thermal features and machine learning	5
Numerical investigation of clocking effect on unsteady fluid flow in vicinity of tongue for centrifugal pump with vaned diffuser	5
Efficiency analysis and heating structure design of high power electromagnetic thermal energy storage system	5
Thermal simulation of gas engine driven heat-source tower heat pump	5
Effects of IGVF on the performance and internal energy loss mechanisms of a two-stage booster pump under cryogenic liquid CO ₂ condition	5
Fast multi-objective optimization design of gas turbine L-inlet duct	4
Numerical investigation on conjugate heat transfer characteristics of film and vortex composite cooling under rotating conditions	4
Numerical study on the influence of inlet distortion on integrated nacelle fans based on coupling crosswind and angle of attack	4
Effect of twisted blade roots on the performance and internal flow of non-volute centrifugal fan	4
Mechanism analysis and uncertainty quantification of blade thickness deviation on rotor performance	4
Energy-based wind vibration control of turbines equipped with nonlinear tuned mass damper inerter considering soil-structure interaction	4
Thermal performance of nanofluids in a sinusoidal channel with embedded porous region	4
Investigation of the internal flow characteristics of a mixed-flow pump in the hump region	4
Analytical modeling and performance improvement of an electric two-stage centrifugal compressor for fuel cell vehicles	4
Numerical study on cavitation flow and induced pressure fluctuation characteristics of centrifugal pump	4
Availability monitoring and improvement method for in-service nuclear power plants based on high-precision prediction of availability	4
Experimental and numerical comparisons among various skewed blades of low speed axial fan rotors	4

Effect of blockage ratio on flow field and combustion characteristics in an integrated cavity-strut dual-mode ramjet combustor	4
Wind turbine power prediction via deep neural network using hybrid approach	4
Uncertainty effects of blade geometric deviations on the aerodynamic stability of a high-load transonic axial compressor	4
Research on the optimization method of energy consumption of helical surface machining considering spindle vibration	4
Erratum to “Characteristics of the axial compressor with different stator gaps in compressed air energy storage system”	4
Experimental study of renewable hydro powered tyre piston pumps for water supply and a case for application of similitude theory	4
Study on the abnormal noise and control strategy in hydropower units	4
Integrated aerodynamic optimization for stationary components of squirrel cage fan Considering impeller-Volute interaction	4
Utilizing artificial intelligence to develop an advanced compressor airfoil family for industrial, aero-derivative, and heavy-duty gas turbines	3
Numerical and experimental analysis of guide vane pivot torque prediction in the reversible pump-turbine	3
Investigation of turbulent flow in vortex cold-wall combustion chamber under different spark ignition times	3
Assessment of the effectiveness of ventilation for gas turbine generator set safety	3
Adaptive model predictive control for constant speed regulation of an accumulator-assisted hydromotor drive under varying load conditions	3
Influence of aspect ratio on aerodynamic and mechanical design of compressor inlet stage in heavy-duty gas turbines	3
Rotordynamic characteristics of a novel labyrinth seal with partition walls and helical groove teeth	3
Thermal exergo-economic investigation of heat exchanger assisted with inserts under CQD nanofluid	3
GA-optimized cascade control strategy of DFIG-Based twin-rotor wind turbines	3
Numerical investigation on the combined effects of pinching and rotation on the performance of a high-speed centrifugal compressor with a vaneless diffuser	3
Part-load performance of a pure H ₂ /O ₂ gas turbine cooled by steam from a bottoming-cycle	3
Advanced exergoeconomics of a steam power plant based on double-tier splitting of exergy destruction rates	3
Investigation of non-axisymmetric endwall contouring in a high loaded turbine stator cascade	3
Enhancing efficiency in CO ₂ scroll compressors: A data-driven optimization approach incorporating clearance tolerance	3
Performance enhancement of solar photovoltaic modules using graphene-enhanced Glauber’s salt eutectic phase change material for advanced thermal management	3
Numerical investigation of performance of an interdigitated polymer electrolyte membrane fuel cell with a porous rib	3
Numerical investigation of H2/Air fueled micro combustion characteristics with trapezoidal ribs for micro thermophotovoltaic applications: Effect of rib height	3
Exploration of the mechanism and prediction of jet pump feature structure optimization for the enhanced pumping performance	3
Series vs. Parallel connections in BIPV arrays: A performance-based assessment under different irradiance scenarios	3
Optimization of low-head shaft tubular pumping systems based on entropy production theory	3
Effect of the relative radial position of the flow components on the exchange flow characteristics of a regenerative flow pump	3
A combined experimental and computational investigation of an inducer’s characteristics with gas-water two-phase flow	3
A genetic programming approach for the prediction of solar chimney power plant power	3
Enhanced heat transfer in a tube with fish scale bionic rib	3
Investigation into the influence of combustion system based upon tumble flow on engine performance of opposed-piston two-stroke engine	3
Experimental and numerical study on the influence of pneumatic parameters on the flow structure in trapped vortex combustor	3
Numerical investigation on vortex cooling flow and heat transfer characteristics for gas turbine blade with variable coolant chamber cross-sectional shapes	3
Machine learning based predictive maintenance framework for belt-pulley systems	3
A study of the effects of housing tongue design on radial turbine performance	3
Demand-side frequency regulation of power grids using inverter-based thermostatically controlled loads	3