OOIR: Observatory of International Research

Papers

(The H4-Index of Journal of the European Ceramic Society is 58. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-09-01 to 2025-09-01.)

Article	Citations
Editorial Board	311
Dry tribological behavior of 0/90° continuous carbon fiber reinforced ZrB2 based UHTC-material	197
Corrigendum to “Interdiffusion at electrochemical interfaces between yttria-stabilized zirconia and doped ceria” [J. Eur. Ceram. Soc. 43 (2023), 6189–6199]	147
Highly porous carbon-SiC composites with continuous carbon fibers for the production of radioisotopes in ISOL facilities	137
Tuning the carbon content of silicon carbonitride SiCN(O) materials obtained from hydrosilylation-derived polysilazanes	133
High-performance SiO2-Sr3(PO4)2 low-ε dielectric ceramics for MW/THz applications	131
Extremely high corrosion resistance of Zn Ni1–Cr2O4 spinel as sidewalls in the aluminum electrolyte	126
Investigation of the structural and piezoelectric characteristics of (1-x)Pb(Zr, Ti)O3-xPb(Zn0.4Ni0.6)1/3Nb2/3O3 ceramics with R-PC-T multistructure	116
Actuation mechanisms in mixed-phase K0.5Bi0.5TiO3-BiFeO3-PbTiO3 ceramics	113
WITHDRAWN: Porous Si3N4 ceramics with uniform microstructure fabricated by in-situ pre-gel casting combined with non-directional freeze-drying	107
Particle migration in large cross-section ceramic on-demand extrusion components	106
Development of self-cleaning matte ceramics based on polycrystalline hexaferrite and its application in oil removal	99
Dense La0.3Sr0.7TiO3 interconnect sintered in air atmosphere at a reduced temperature with improved conductivity for solid oxide electrochemical cells	95
Carbon contamination of elemental beta-boron promoted a stable boron carbide by spark plasma sintering	93
Li3V2(PO4)3 sintering atmosphere optimisation for its integration in all-solid-state batteries	92
Aqueous tape casting of lithium metazirconate (Li2ZrO3) thin sheets	91
Few-layered-graphene - Si3N4 composite powders prepared by decomposition of methane onto a Si3N4 powder bed: Control of the average number of layers in the graphene stack	89
Effect of La3+	88
Crystallization in the TeO2 - Ta2O5 - Bi2O3 system: From glass to anti-glass to transparent ceramic	87
Tuning anisotropic thermoelectric properties of TiS2– compounds via intercalating iron	87
A novel vinyl-bridged graphene oxide/polycarbosilane precursor for harsh environment-resistant ceramic temperature sensor	85
Application of an improved testing device for the study of alumina dissolution in silicate slag	81
Characterization of inclusions inhibiting high thermomiotic behavior of Y2W3O12	81
Effects of in-situ carbon layer and volume fraction of SiC fiber on the mechanical properties and fracture behaviors of SiCf/SiC composites fabricated by a modified PIP method	78
Application of mullite-zeolite-alumina microfiltration membranes coated by SiO2 nanoparticles for separation of oil-in-water emulsions	78

First principles calculations and synthesis of multi-phase (HfTiWZr)B2 high entropy diboride ceramics: Microstructural, mechanical and thermal characterization	78
Atomic layer deposition and characterization of Bi1Se1 thin films	76
A comparative study on dielectric and mechanical properties of porous β-Si3N4 ceramics by controlling porosity and microstructure	76
Residual stress induced failure of Ti-6Al-4V/Si3N4 joints brazed with Ag-Cu-Ti filler: The effects of brazing zone’s elasto-plasticity and ceramics' intrinsic properties	75
Additive manufacturing low shrinkage Si-based composite ceramics with SiCO microsphere/polyvinyl silicon acetylene slurry	75
A novel low-loss Ba12InNb9O36 microwave dielectric ceramic with 18-layer hexagonal perovskite structure	74
Interface structure dependent step free energy and grain growth behavior of core/shell grains in (Y, Mg)-doped BaTiO3 containing a liquid phase	73
High-speed deposition of silicon nitride thick films via halide laser chemical vapor deposition	73
Sequential ion-electron irradiation of zirconium carbide ceramics: Microstructural analysis	71
Intermediate stage densification kinetics of high-entropy ceramics during spark plasma sintering	71
Defect redistribution along grain boundaries in SrTiO3 by externally applied electric fields	69
Growth mechanism and sintering properties of high crystallinity Archimedean polyhedral (Zr0.5Hf0.5)B2 nanoparticles	68
Effect of residual carbon on the phase transformation and microstructure evolution of alumina-mullite fibers prepared by sol-gel method	68
Enhanced electrocaloric effect of barium titanate-based ceramic thick films through regulating the internal stress and multilayered structure	67
In situ monitoring of the mechanical and electrical property changes of amorphous Si–Al–C–O fibers during heating to 1900 °C and correlation of these changes with the accompanying structural and cryst	67
Exploring point defects and trap states in undoped SrTiO3 single crystals	66
High temperature oxides for selective absorption of thermal radiation	66
CMAS corrosion resistance, thermal shock resistance and numerical simulation of novel surface micromesh thermal barrier coatings	65
A novel method for fabricating brick-mortar structured alumina-zirconia ceramics with high toughness	65
Effects of high-energy ball milling and reactive spark plasma sintering on the densification, microstructure, and mechanical properties of ultra-fine and X-ray pure ZrB2-SiC composites	64
Mechanical properties of ceria-calcia stabilized zirconia ceramics with alumina additions	64
Experimental study and DFT calculations of improved giant dielectric properties of Ni2+/Ta5+ co-doped TiO2 by engineering defects and internal interfaces	63
Suppressing the non-switching contribution in BiFeO3-Bi4Ti3O12 based thin film composites to produce room-temperature multiferroic behavior	62
A novel gradient CrSi2-ZrSi2-SiC-Si coating for long-term oxidation protection of C/C composites at 1773 K	61
Heat treatment effect on coating shock resistance of thermal barrier coating system with different types of bond coat	61
Raman spectra, bond characteristics, and microwave dielectric properties of Gd2Mo3O12 ceramics	61
Preparing the SiC coated C/C composites with excellent mechanical and antioxidative properties using a buffer layer	61
Ablation behavior at full-temperature ranges of C/SiC in combustion gases containing water vapor	60
A review of surface topographical modification strategies of 3Y-TZP: Effect in the physicochemical properties, microstructure, mechanical reliability, and biological response	60
Direct welding of diffuse alumina ceramics by ultrashort pulse laser	59
Relationships between fracture toughness, Y2O3 fraction and phases content in modern dental Yttria-doped zirconias	59
Effect of surface air cooling on the high frequent cyclic ablation of C/C-SiC-AlSi composite prepared by slurry injection technique	59
Exploring processing, reactivity and performance of novel MAX phase/ultra-high temperature ceramic composites: The case study of Ti3SiC2	59
Rational design of a novel mullite aerogel with extremely high mechanical strength and anti-oxidation behavior for advanced thermal protection in extreme environments	58
A novel strategy for synthesizing porous ZrB2-SiC ceramics via boro/carbothermal reaction process templated pore-forming approach	58