OOIR: Observatory of International Research

Papers

(The TQCC of Advanced Composite Materials is 4. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-09-01 to 2025-09-01.)

Article	Citations
Experimental investigation on interlaminar tension strength of curved composite laminates subjected to four-point bending load	58
Electromechanical behavior of radar-absorbing thermoplastic composites with nickel-coated glass/polyamide 6 under high humidity conditions	44
Multi-objective optimization for CF/PPS-stainless steel induction welding with pin structure based on SSA-BP neural network	23
Static analysis of FGM porous cooling plates with cutouts: a multilayered approach	22
Thermostructural Characterization of Silicon Carbide Nanocomposite Materials via Molecular Dynamics Simulations	14
Highly efficient and reusable polyacrylonitrile-based nanocomposite sorbents for oil spill removal	13
Experimental Evaluation of Fatigue Properties of Carbon Fiber/Epoxy Matrix Interface and Numerical Simulation of Transverse Cracking under Cyclic Load	13
Investigation on mechanical properties and stealth characteristics of a novel gradient-stitched composite structure	13
Effect of addition of graphene nanoplatelets on the mechanical properties of triaxially braided composites	12
Analysis of free vibration characteristics of non-uniform graphene-reinforced axially functionally graded nanocomposite beam	12
Influence of lattice geometry on energy absorption and puncture resistance in 3D-Printed ABS structures for advanced medical implants	12
Mechanical properties and damage behavior of bi-directional glass fiber non-crimp fabric laminates: effects of laminate and nesting configurations	12
Hybrid glass-carbon fiber composites for solar greenhouse dryer trays: a 3D computational analysis	11
Critical comparison of potential machine learning methods for lightning thermal damage assessment of composite laminates	11
Thermomechanical performance and multiscale modeling of hexagonal boron nitride modified out-of-autoclave manufactured silica fiber reinforced phenolic composites	11
Active thermography inspection of CFRP using cyclic heating and Fourier transform—comparison with flash heating method	11
High-temperature co-cured phenolic resin damping composite embedded with fluororubber film	11
Fatigue and static characterization on the behavior of electrospun nano-fiber veil toughened composites	11
Mesoscale modeling of ultra-thin woven fabric composite subjected to in-plane loading	11
Crack monitoring and repair model of SMA composite material based on strain transfer	10
Study on microstructure and mechanical properties of hybrid aluminium matrix composite with ZrO₂ and Ni particle as reinforcement fabricated through FSP route	10
Mechanical characterization of ultrasonically welded CF/PEEK laminates by short beam shear test	10
Synthesis and application of the rGO-CuO/Cu ₂ O nanocomposite electrode regulated by CTAB in flexible asymmetric supercapacitor	10
Experimental investigation of eco-friendly fiber-reinforced concrete using recycled and natural fibers, integrated with recycled aggregates	9
Correction	9

Impact of internal pressure regulation in filament winding on the quality of composite cylinders: a study with pulse-echo ultrasonic propagation imaging	9
Interface stress transfer in an extruded ABS-rGO composite filament	9
The use of fibre reinforced polymer composites for construction of structural supercapacitors: a review	9
A micromechanical constitutive model for porous ferromagnetic shape memory alloys considering magneto-thermo-mechanical coupling	8
Improving fatigue characteristics of ply drop-off in composite laminate with ply curving termination	8
Assessing thermoelectric performance of quasi 0D carbon and polyaniline nanocomposites using machine learning	8
Unravelling the role of nanofillers towards the stability of polymer matrix composite in marine environment	8
Statistical safety evaluation method for composite high-pressure hydrogen vessels considering stacking sequence effect and fiber strength development rate	8
The contribution of numerical models to Lamb-wave-driven NDT processes – part II: experimental design and numerical studies	7
Prediction of transverse crack multiplication of CFRP cross-ply laminates under tension-tension fatigue load	7
Magneto-hygro-thermal vibration analysis of the viscoelastic nanobeams reinforcedwith carbon nanotubes resting on Kerr’s elastic foundation based on NSGT	7
Effects of cryogenic environment on strength properties of double-lap composite bonded joints	7
Characterization of thin-walled self-healing microcapsules reinforced with multi-walled carbon nanotubes	7
Effective utilization of unidirectional laminates for mass reduction in composite blades of multi-MW wind turbines	7
Fundamental experiments of bird-strike, and derivation of empirical equations for damage	7
Enhanced thermal conductivity of polyamide nanocomposites involving expanded graphite–carbon nanotube network structure using supercritical CO ₂	7
Shear strength and failure modes of double-lap bi-material CFRP/Ni-Cr alloy joint under severe environmental conditions	6
A mathematical method for the vibration analysis of composite lattice plates under In-plane compressive loads	6
Improvement of tensile strength and toughness in aramid/epoxy composites by sequential air plasma and (3-glycidyloxypropyl) trimethoxysilane treatments	6
Co-bonding of carbon fibre-reinforced epoxy and galvanised steel with laser structured interface for automotive applications	6
Kink band orientation of 3D printed continuous carbon fiber composites under compressive loading	6
A multiscale framework for composites considering interphase based on molecular dynamics and finite element method	6
Development and experimental verification of an advanced 3D elastoplastic progressive damage model for composite materials	6
Proposal of a metal conical pin-based connection method to enable high-strength joining of metal materials and continuous fiber reinforced plastics in multi-structural materials and discussion of infl	5
Comment on ‘optimum structural design of CFRP isogrid cylindrical shell using genetic algorithm’	5
Improvement in shape memory polymer properties by applying different type of carbon-based fillers	5
Layer-wise compaction 3D printing: void reduction and interfacial enhancement for continuous carbon fiber–reinforced thermoplastics	5
Humid heat aging of biphenyl epoxy resin: a combined study of experiments and simulations	5
Experimental investigation of heat performance of carbon fiber heating cable for long-term applications	5
Long-term viscoelastic properties of carbon fiber/epoxy composites using tow prepreg strand specimens	5
Fatigue characteristics of jagged steel pin-reinforced composite hat-joints under pull-off loading	4
Mechanical analysis and bionic improvement on buckling of CFRP tubes with high energy absorption capacity	4
Effect of hygrothermal condition on single-lab shear behavior of induction-welded CF/PEKK thermoplastic composites	4
Experimental characterization of multiscale solidification in thermoset CFRP during gelation for flow and stress modeling	4
Techno-economic analysis of type III and IV composite hydrogen storage tanks for fuel cell vehicles	4
Intelligent structural health monitoring of composite structures using machine learning, deep learning, and transfer learning: a review	4
Nonlinear behavior mechanism of change in electrical resistance on 3D printed carbon fiber / PA6 composites during cyclic tests	4
Evaluation of mechanical and corrosion properties of AZ91-GNP nanocomposites fabricated using the SMART/MA process	4
Mechanically robust, highly toughened, corrosion and impact resistant epoxy/silica nanocomposites by UV curing 3D printing technology	4
Elucidating the green energy production potential of biomimetically fashioned [OFR-MnO/ZrO ₂ ]-MMO electrocatalyst	4