OOIR: Observatory of International Research

Papers

(The H4-Index of Advanced Powder Technology is 35. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-06-01 to 2026-06-01.)

Article	Citations
Full title (Editorial Board Members)	75
Carbon nanotubes growth in modified bluecoke powders: Preparation and characterization, formation mechanism of CNTs, and potential application	72
Effects of external nitrogen sources on the electrochemical properties of nitrogen-doped carbon materials from bio-oil distillation residue	72
Full title (Editorial Board Members)	72
Capturing the dynamics of a two orifice silo with the μ(I	61
Full title (Editorial Board Members)	60
Experimental study on the prevention of microbial fouling accumulation on a Ni-Cu-P modified heat exchange surface	59
Inside Front Cover (Aims & Scope, Editors)	59
Inside Front Cover (Aims & Scope, Editors)	56
Computational Fluid Dynamics analysis of a jet-induced attrition	53
Data interpolation and characteristic identification for particle segregation behavior and CNN-based dynamics correlation modeling	52
Simulation of gas-solid combustion characteristics in a 1000 MW CFB boiler for supercritical CO2 cycle	50
Fabrication of a carbon/polytetrafluoroethylene nanoparticle-coated antistatic bag filter using air-assisted electrospraying	47
Rolling friction coefficients: a key factor in the dynamic response of squat silos subjected to grain central discharge	46
Mechanism of magnetite iron ore concentrate morphology affecting the pellet induration process	44
Microstructure and mechanical properties of spark plasma sintered austenitic ODS steel	44
Implementation of a Yukawa force model in polymer-induced bridging flocculation of hematite particles using CFD-DEM	43
Aerosol-phase synthesis of bimetallic NiCu oxide-decorated CeO2 nanoparticle cluster for catalytic methane combustion	42
Preparation and characterization of a special high speed steel powder prepared by plasma rotating electrode process	41
DEM study of mixing performance of superquadric particles in an industrial-scale ribbon mixer	41
DEM analysis of the media size ratio and agitator shaft geometry effects on grinding performance in a mixed-media stirred mill	39
Sodium trithiocarbonate as an activator for malachite xanthate flotation: Experimental study and practical application	39
Numerical study and multi-objective optimization of flexible screening process of flip-flow screen: A DEM-FEM approach	39
pH-responsive prodrug containing Zr-based MOF and aldehyde-based drug; anionic hydrogel coating as a smart delivery system	39
Acoustic separation and fractionation of property-distributed particles from the gas phase	39

High performance C-A-S-H seeds and sulfate-rich lithium slag by nano-mechanochemical method on cement hydration: Microstructure and mechanical performance	39
Enhanced synthesis of plasmonic mesoporous Ag-doped ZnAl2O4 nanophotocatalyst via synergistic ultrasound and microwave irradiation for efficient organic dye degradation	38
Evaluation of the use of silica extracted from industrial waste with an ultrasonic bath and modifications to the aging stage in the synthesis of ZSM-5 and its application in pyrolysis	38
Efficient separation of uranium in solution by ZnFe2O4 doped with TiO2: Adsorption behaviors and mechanism study	38
The synthesis of high purity Ti3AlC2 MAX phase via molten salt method	35
Comparative study of powder characteristics and mechanical properties of Al2024 nanocomposites reinforced with carbon-based additives	35
Effect of the symmetrical eccentric load on the soil arching effect in granular soil via 2D DEM trapdoor tests: An insight from particle motion to mechanical behaviour	35
Comparative study on centrifugal granulation behavior of blast furnace slag and copper slag	35
Iron removal from PLK rock: An optimisation study using response surface methodology	35
Parametric analysis and optimization of gas-particle flow through axial cyclone separator: A numerical study	35