Experimental Heat Transfer

(The TQCC of Experimental Heat Transfer is 6. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-06-01 to 2024-06-01.)
Experimental hydrothermal characteristics of concentric tube heat exchanger with V-cut twisted tape turbulator using PCM dispersed mono/hybrid nanofluids28
Evaluation of the performance analysis of an improved solar air heater with Winglet shaped ribs25
The effect of circular hole spring tape on the turbulent heat transfer and entropy analysis in a heat exchanger tube: an experimental study23
Experimental investigation for heat and flow characteristics of solar air heater having symmetrical gaps in multiple-arc rib pattern as roughness elements20
Establishment of correlations for the thermo-hydraulic parameters due to perforation in a multi-V rib roughened single pass solar air heater20
Experimental study on the heat transfer enhancement in a rectangular channel with curved winglets20
Heat transfer characteristics and boiling heat transfer performance of novel Ag/ZnO hybrid nanofluid using free surface jet impingement20
Analysis of the effect of perforation in multi-v rib artificial roughened single pass solar air heater: - Part A19
Experimental investigation of the thermal behavior a single-cavity and multiple-orifice synthetic jet impingement driven by electromagnetic actuator for electronics cooling19
Performance comparison of sensible and latent heat-based thermal storage system during discharging – an experimental study19
Performance assessment of double-pass parallel flow solar air heater with perforated multi-V ribs roughness — Part B18
Prediction of heat transfer in a circular tube with aluminum and Cr-Ni alloy pins using artificial neural network17
Heat transfer characteristics of flat and concave surfaces by circular and elliptical jet impingement16
Thermal performance of a flat-plate solar collector using aqueous colloidal dispersions of multi-walled carbon nanotubes with different outside diameters16
Thermal analysis of jet impingement on hemispherical protrusion on heated surface16
Nucleate pool boiling heat transfer above laser machining heating surfaces with different micro-cavity geometric shape for water-aluminum oxide nanofluid14
Effect of phase change temperatures and orientation on the thermal performance of a miniaturized PCM heat sink coupled heat pipe13
Experimental results on two-phase heat transfer enhancement in microstructured corrugated plate heat exchangers13
Effect of perforated concave delta winglet vortex generators on heat transfer and flow resistance through the heated tubes in the channel13
Investigations on the effect of disturbed flow using differently configured turbulators and Alumina nanofluid as a coolant in a double tube heat exchanger12
Experimental and numerical investigation of diffusion absorption refrigeration system working with ZnOAl2O3 and TiO2 nanoparticles added ammonia/water nanofluid12
Effect of a unique winglet twisted tape insert on thermal and hydraulic properties of tubular heat exchanger12
Experimental investigation of heat transfer augmentation due to obstacles mounted in solar air heater duct11
Thermal performance evaluation of a latent heat thermal energy storage unit with an embedded multi-tube finned copper heat exchanger10
Investigation of the condensation heat-transfer between the wet air and 3-D finned-tube heat exchanger surface with different anti-corrosion coatings10
Effect of new punched vortex generators in a rectangular channel on heat transfer using Taguchi method9
Molecular dynamic simulation and experimental data on graphene wettability on heated structured surfaces9
Mass and heat transfer at a helical coil imbedded in a fixed bed of cylinders with upward cocurrent gas-liquid flow9
Experimental study of using system of flat heat pipe-phase change material inclusion heat sink for thermal regulation of simulated PV9
Condensation heat transfer characteristics of a mixture of R1234ze (E) and R152a flowing inside a horizontal micro-fin tube9
Flow boiling heat transfer performances of R1234ze(E)/R152a in a horizontal micro-fin tube9
Heat transfer measurements of a turbine endwall with engine-representative freestream turbulence and inlet swirl8
Nanodiamond Colloids heat transfer behavior in electronics thermal management – an experimental study8
Numerical and experimental study of the influence of extended surfaces in rectangular channel subjected to constant heat flux8
Effect of unidirectional surface roughness on heat transfer performance of spray cooling8
Influence of saturation temperature and heat flux on pool boiling of R245fa7
Experimental and numerical investigation of the thermal performance of impinging synthetic jets with different waveforms7
Heat transfer performance of microchannels with round grooves and ribs based on field synergy principle and entropy production analysis7
Solid-liquid mass transfer in a bubble column reactor with tube bank internals7
Experimental analysis of local and average heat transfer between circular impinging jet and flat plate7
Study on the air-side flow and heat transfer characteristics of corrugated fin under low-pressure environment7
Experimental Investigation of The Influence of Modifying the Inner Tube Outer Surface on Free Convection in A Concentrated Double Pipe7
Experimental investigation of the heat transfer for non-circular tubes in a turbulent air cross flow7
Experimental investigation of natural convection Al 2 O 3 -MWCNT/water hybrid nanofluids inside a square cavity7
Experimental investigation on thermo hydraulic performance of ferronanofluid flow in a dimpled tube under magnetic field effect7
Experimental investigation of substrate board orientation effect on the optimal distribution of IC chips under forced convection7
Experimental investigation of flow and thermal characteristics of synthetic jetissuing from sharp-edged orifices7
Estimation of the local convective heat transfer coefficients of low frequency two-phase pulsating impingement jets using the IHCP7
Influences of twisted turbulators arrangements on heat transfer and airflow resistance over absorber plate of solar air heater6
Experimental study of heat transfer in a microchannel with pin fins and sintered coatings6
Thermal diffusivity measurement of stainless-steel alloys through use of the Angstrom’s method6
Experimental parametric study of hierarchical micro/nano electrodeposited (six-step) pattern with respect to volcano-shape morphology in pool boiling performance augmentation6
Enhancement of dropwise condensation heat transfer on hydrophilic-hydrophobic hybrid surface using microparticles6
Experimental examination of condensation heat transfer enhancement with different perforated tube inserts6
Transparent nanofluids with high thermal conductivity for improved convective thermal management of optoelectronic devices6
Acoustics and Heat Transfer Characteristics of Piezoelectric Driven Central Orifice Synthetic Jet Actuators6
Experimental study of electrospray deposition method parameters on TiO_2 coating structure in pool boiling performance enhancement6
Saturated and subcooled pool boiling heat transfer in mixtures of water and glycerin6
Experimental and numerical study of thermal-hydraulic performance in a heat exchanger tube with circular ring’s angular cutting inserts6
Experimental Investigation on Thermal Performance Characteristics of Rotating Packed Bed6
Exergetic efficiency analysis of impingement jets integrated with internal conical ring roughened solar heat collector6
The aspect ratio effect on the performance of a cam-shaped cylinder in crossflow of air6
Experimental studies of the pool boiling heat transfer enhancement capability and mechanisms of the micro-pillared surfaces on copper substrate6