TAPPI Journal

Papers
(The TQCC of TAPPI Journal is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-02-01 to 2025-02-01.)
ArticleCitations
Setting priorities in CNF particle size measurement: What is needed vs. what is feasible25
Sulfur makeup in an unbleached kraft pulp mill9
A new and quick testing method for evaluating commercial OCC recycled pulp9
Comparing a linear transfer function-noise model and a neural network to model boiler bank fouling in a kraft recovery boiler9
Quantification of block testing for coated paper substrates8
Test method and coating composition impact on measured moisture vapor transmission rate for waterborne coatings on paper8
Amphoteric dry strength chemistry approach to deal with low-quality fiber and difficult wet-end chemistry conditions in the Asian and North American markets8
Quantification of the degree of preference for different tissue products based on a hand-felt tissue test panel6
July 20236
Pilot scale black liquor concentration using pressure driven membrane separation6
Paper bending stiffness and web tension measurement from a running web using a vacuum and computer imaging6
Research on flame-retardant paper prepared by the method of in-pulp addition of ammonium polyphosphate6
Dynamic CFD modeling of calcination in a rotary lime kiln with an external dryer6
Editorial: Critical literature reviews in open source journals6
Control of continuous digester kappa number using generalized model predictive control6
Dissolution of wood components during hot water extraction of spruce6
Editorial: The next phase of research in academia and industry6
Polyvinylamine as a wet-end additive: Effects of pH and anionic contamination5
Editorial: Special issue showcases new additive approaches for a lignocellulose-based future5
Factors affecting deposit formation in foul condensate stripping systems5
Characterizing rheological behavior and fluidization of highly refined furnishes for process optimization5
Remembering Dr. Peter W. Hart: Dedicated leader, mentor, friend5
A true green cover for industrial waste landfills5
Editorial: Special pulping and engineering issues of TAPPI Journal yield important recovery cycle research4
Rethinking the paper cup — beginning with extrusion process optimization for compostability and recyclability4
Determining operating variables that impact internal fiber bonding using Wedge statistical analysis methods4
Three-dimensional visualization and characterization of paper machine felts and their relationship to their properties and dewatering performance4
Incorporation of post-consumer pizza boxes in the recovered fiber stream: Impacts of grease on finished product quality4
Boiler retrofit improves efficiency and increases biomass firing rates4
An evaluation of household tissue softness4
Tetraethyl orthosilicate-containing dispersion coating — water vapor and liquid water barrier properties3
Coatings for sustainable paper-based flexible packaging: Barrier properties and processability3
Kraft pulp viscosity as a predictor of paper strength: Its uses and abuses3
A model black liquor formulation for use in development and evaluation of membranes for concentrating weak black liquor3
Commercially relevant water vapor barrier properties of high amylose starch acetates: Fact or fiction?3
Microbial load and proliferation associated with various face mask types and sources during the COVID-19 pandemic3
Predicting strength characteristics of paper in real time using process parameters3
August 20223
Nanocellulose–cationic starch– colloidal silica systems for papermaking: Effects on process and paper properties3
January 20233
April 20223
Calender barring review with experiences2
On the diagnosis of a fouling condition in a kraft recovery boiler: combining process knowledge and data-based insights2
Water chemistry challenges in pulping and papermaking – fundamentals and practical insights: Part 1: Water chemistry fundamentals and pH2
September 20222
Experiments and visualization of sprays from beer can and turbo liquor nozzles2
Convolutional neural networks enhance pyrolysis gas chromatography mass spectrometry identification of coated papers2
Web lateral instability caused by nonuniform paper properties2
Causes of poor dregs settling in a green liquor clarifier2
Considerations in managing wastewater odor at pulp and paper operations2
Impact and feasibility of a membrane pre-concentration step in kraft recovery2
Eucalyptus black liquor properties in a lignin extraction process: density, dry solids, viscosity, inorganic, and organic content2
Pulp and paper mills: The original biorefineries — past performance and limitations to future opportunities2
A feasibility study of using the organic Rankine cycle for power generation from the flue gases of recovery boilers2
Improvements in oil and grease resistance (OGR) test methodology for waterborne barrier coatings2
Production and characterization of furanic bio-oil from Kawayan kiling (Bambusa vulgaris Schrad ex. Wendl) using molten citric acid in an open system2
A new method of studying the fundamental mechanisms involved in pigment liberation from recycle papers2
Utilization of kraft pulp mill residuals2
Ultrastructural behavior of cell wall polysaccharides2
The role of gas dispersion in the oxygen delignification process2
An analytical approach to assess the interrelation of surface properties and softness of tissue paper2
October 20232
Multilayering of conventional latex-based dispersion coatings containing small amounts of silica nanospheres: Runnability on a pilot scale flexographic coater and barrier performance2
Experimental investigations into fold cracking of double coated barrier dispersion coatings2
August 20242
CFD and predictive modeling of temperature and calcination in a rotary lime kiln – Potential for steadier kiln operation2
Review of coating cracking and barrier integrity on paperboard substrates2
The effect of contact time between CPAM and colloidal silica on the flocculation behavior in the approach flow1
Influence of pallet pattern on top-to-bottom compression performance of unitized loads1
Development of converging-diverging multi-jet nozzles for molten smelt shattering in kraft recovery boilers1
March 20231
The effect of microfibrillated cellulose on the wet-web strength of paper1
Evaluation of rice straw for purification of lovastatin1
January 20221
Probing the molecular weights of sweetgum and pine kraft lignin fractions1
Advantages of lean duplex stainless steels in the pulp and paper industry1
Preparing prehydrolyzed kraft dissolving pulp via phosphotungstic acid prehydrolysis from grape branches1
Modeling the dynamics of evaporator wash cycles1
Furnishing autohydrolyzed poplar weakly alkaline P-RC APMP to make lightweight coated base paper1
Edge crush testing methods and box compression modeling1
Perfluoroalkyl and polyfluoroalkyl substances (PFAS) — Fibrous substrates1
Filtration efficiency and breathability of selected face masks1
Effect of pressure and time on water absorption of coated paperboard based on a modified Cobb test method1
Co-ground mineral/microfibrillated cellulose composite materials: Recycled fibers, engineered minerals, and new product forms1
Next generation dry strength additives: Leveraging on-site synthesis to develop high performance glyoxalated polyacrylamides1
The Effect of Component Removal Upon the Porous Structure of the Cell Wall of Wood. II. Swelling in Water and the Fiber Saturation Point1
November 20211
Key material properties in crease cracking of kraft paper1
A fast and non-destructive alternative to the burnout method for paperboard quality inspections using phase-contrast X-ray imaging1
Spraying starch on the Fourdrinier— An option between wet end starch and the size press1
Improving refining efficiency with deflocculation1
Multifunctional starch-based barrier materials1
External fibrillation of wood pulp1
An analytical method to quantitatively determine the amount of polyamide epichlorohydrin (PAE) in paperboard and white water1
A guide to eliminating baggy webs1
Comparative study of guar gum and its cationic derivatives as pre-flocculating polymers for PCC fillers in papermaking applications1
Effects of different soda loss measurement techniques on brownstock quality1
Energy saving potential of interstage screen fractionation for production of board grade BCTMP1
Formic acid pulping process of rice straw for manufacturing of cellulosic fibers with silica1
Pareto-based design of experiments for identifying and comparing optimum sealing parameters of heat sealing applications in packaging machines1
Understanding wet tear strength at varying moisture content in handsheets1
May 20231
May 20211
Non-process elements in the recovery cycle of six Finnish kraft pulp mills1
Application of foamed additives to the surface of wet handsheets1
July 20221
Utilization of palm fiber as papermaking materials: Microscopic structure and chemical pulping1
Rewet suppression through press felt engineering1
In-situ green synthesis and adsorption on methylene blue of copper-based metal organic framework/cellulose/chitosan (CCTSA/HKUST-1) composite aerogel1
Modeling the influence of rheology on smooth rod coating systems1
Mechanical modification of softwood pulp fibers using a novel lightweight vertical bar plate1
February 20221
Application of ATR-IR measurements to predict the deinking efficiency of UV-cured inks1
Editorial: The innovation engine and the forest products industry value chain1
A discrete element method to model coating layer mechanical properties with bimodal and pseudo-full particle size distributions1
SCC susceptibility of chromized type 409 stainless steel in alkaline chloride solutions at ambient temperature and pressure1
The role of hornification in the deterioration mechanism of physical properties of unrefined eucalyptus fibers during paper recycling1
Continuous tannin extraction by use of screw reactor1
Colloid chemical aspects of paper formation in the presence of nanofibrillated cellulose and cationic starch1
0.051837921142578