Electrical Engineering in Japan

Papers
(The TQCC of Electrical Engineering in Japan is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)
ArticleCitations
15
Noninvasive Biofluorometric Sensing and Imaging Analysis of Blood VOCs for Novel Wearable Sensor15
Development of a Control Method to Mitigate Fluctuations in Power Supply Voltage Caused by Variations in the Load of Shinkansen Trains7
A Proposal of the Improved Method for Measuring Insulation Resistance Between a Photovoltaic Module String and the Earth Using the Self‐Biased Method7
Issue Information5
Issue Information5
Development of Air Entrainment Detection Method for Pumps Using Motor Current Signals4
A novel method applicable to large‐scale active magnetic shielding system which effectively compensates gradient magnetic fields originated from the surrounding buildings4
A study of odor reproduction using multi‐component olfactory display4
Application and Performance Evaluation of Backstepping Control for Drone 3D Trajectory Control3
Issue Information3
Heatsink‐less MMC Active Power Filter Using Low‐Voltage Si‐MOSFETs for Air Conditioner Applications3
3
Development of a circuit breaker system using a linear motor with opposite magnetic poles3
Space Charge Accumulation Behavior of Fluorinated Insulating Materials Irradiated by Proton under DC Voltage3
Development of capacitive‐coupled hall‐type MHD generator3
An Evaluation of Insulative Property of Polluted Silicone Rubber by Non‐Contact Surface Resistivity Measurement2
Characteristics of electrical field of high‐current air arc in restricted slit‐like space by polymer plates2
Development of a New Unit Commitment Method With Quantum Predator Prey Brain Storm Optimization2
Proposal of angle detection method for concentrated winding bearingless motors with less magnetic interference due to current2
Atmospheric pressure argon plasma jets I – Measurements of spatial distribution for visible emission spectrum and vacuum ultraviolet2
Proposal of the Rocking Electric Power Generator Using Pendulum Mechanism for ICT Applications in the Fisheries Industry2
Reduction of magnetic field by low‐order harmonics in magnetic resonant wireless power transfer system using high‐frequency switching2
Mechanism of control instability of control function installed to grid‐following inverter and development of damping controller for stable operation2
Issue Information2
Issue Information2
Traction Drive Motor for Small EVs Using Mass Producible Amorphous Laminated Cores2
An Adjustment Method for Re‐Adhesion Control of Electric Rolling Stock Using Particle Swarm Optimization and its Validation by a Scale Model Railway Vehicle2
Issue Information2
Function and role of bus bar protection relay in distribution substation2
Development of Wearable Multimodal Sensor Probe for Measurement of Core Body Temperature, Heart Rate, and Sweat Rate2
A Calculation Method Based on Analytical Formulas for Inrush Currents and Voltage Dips During Energization2
Development of Phenotypic Microbial Sensing System by AI‐Driven AC Nanopore Method2
Development and Validation of Estimation of Breakdown Voltage of Stator Windings of Generator From Partial Discharge Magnitude2
Oxidation of Iodine Using Ozone by Plasma Emitted in Aqueous Solution1
1
Negative quadrant glitch suppression control of ball‐screw‐driven stage for machine tool by friction compensation and initial value compensation1
Transformer‐less drive and operation stability analysis of dielectric barrier discharge using a double resonance circuit1
Experimental Consideration on Miniaturization of Magnetically Driven Flapping Pico Air Vehicle1
Remaining Life Estimation Technology of AC Mill Motors for Steel Rolling1
Novel dynamic wireless power transfer system using in‐tire and in‐wheel repeater coil for battery electric vehicles1
Bridgeless Power Factor Correction Flyback Rectifier Using a Novel Integrated Transformer1
Evaluation of Temperature Distribution of Oil‐Immersed Transformer Considering Core Gap Insulation Using 3D Thermo‐Fluid Analysis During No‐Load Operation and Cooler Stoppage1
A reference stator flux linkage calculation method for realizing maximum efficiency operation in direct‐torque‐controlled IPMSM drives1
A study on improving shielding performance of shielded cable1
Fast short‐circuit protection under current imbalance condition for multi‐paralleled SiC‐MOSFETs1
Analysis of interference of electromagnetic noise in an electric compressor for vehicle air‐conditioning systems with an integrated mechanical and electrical structure1
Power factor control for inverters under high penetration of distributed generation1
A Development of a Resource Planning Method for Reducing Outage Duration1
Inspection Method for Thinning of Metal Pipes Using Electromagnetic Wave Polarization Characteristics1
Evaluation of Power Control of Secondary Converter Used in SCMaglev WPT System1
A Study on Area Inertia Estimation Method Using Ambient Measurement Data of Tie‐Line Power Flow and Frequency1
Design of a linearization model for three‐phase PWM rectifiers for electrochemical machining1
The high‐frequency phenomenon of copper clad aluminum wires which are lower the alternating current resistance than copper solid wires, and the application of copper clad aluminum wires to the electri1
Common mode conductive noise cancellation for multiphase converter using auxiliary winding1
Optimizing service restoration in distribution systems based on scheduling of crews considering priorities of loads1
Formulation and mixing conditions of magnetic composite materials used for magnetic wedges in an interior permanent magnet synchronous motor1
Limitation of switching frequency to improve characteristics and suppression of input current distortion for critical mode PFC1
Issue Information1
Issue Information1
Highly extendable passive current balancing interleaved high step‐up boost converter using voltage multipliers1
1
Centralized control of large‐scale wind farm for system frequency stabilization of the power system1
A grid frequency control on small scale power system by introduction of variable speed diesel‐driven power plant1
1
A circuit model of electrical wiring nearby building structure for lightning surge analysis1
Microfabrication of surface acoustic wave devices with AlN thin film deposited on half‐inch quartz wafer1
Fault current limiter principle by switching magnetic circuit1
1.018657207489