Transactions of the Indian Ceramic Society

Papers
(The median citation count of Transactions of the Indian Ceramic Society is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-05-01 to 2025-05-01.)
ArticleCitations
Evaluation of Different Fly Ash-Blast Furnace Slag Formulations for Design of Geopolymers in Radioactivity Disposal Applications18
Structural and Electrical Properties of Gd Doped CeO2 (GDC) Nanoceramics for Solid Oxide Fuel Cell Applications17
Application of Silica Aerogel Films to the Fabrication of Surface Acoustic Wave Filters15
Elaboration and Characterization of β-TCP/ZrO2 Cements for Dental Applications12
Effect of Calcination Temperature on the Properties of Nanotitania-Based Extrudates from an Industrial Raw Material11
A Novel Approach to Evaluate the Wear Behavior of CuO Doped Sintered Alumina Ceramics Using Image Processing Models8
Densification Behavior, Microstructural Development and Mechanical Properties of Spark Plasma Sintered α/β-Silicon Nitride Ceramics with Different Rare Earth Oxide Additives8
Thermophysical Properties of Ti 3 SiC 2 MAX Phase Composites with SiC Reinforcement8
Effect of Reaction Time on the Synthesis and Sintering of Magnesium-Aluminium Spinel by Microwave Hydrothermal Synthesis8
Ceramic Manufacturing Workforce in India: Trends, Relative Earnings and Its Determinants7
Extrusion of Silicon Carbide Based Tubular Membrane Incorporated With Coal Fly Ash and Performance Evaluation in Water Treatment7
The Formation of a New Phase during Crystallization of TiO2-Doped Nd2O3-Al2O3-SiO2 Glasses6
Doping Mn Induced Modification on the Crystal Structure, Morphology and Optical Properties of Mechanically Activated SrTiO 3 Powders5
Microstructure, Mechanical and Thermal Insulation Properties of Potassium Hexatitanate Whiskers Thermal Insulation Materials5
Investigation on Physical, Structural and Luminescence Properties of Nickel Oxide Doped Lithium Strontium Borate Glasses4
Mullite Fiber Prepared by Sol-Gel Method Using Low-Molecular-Weight Acids as Modifying Agents4
Impact of Experimental Protocols on the Flexural Strength Testing of Lithium Disilicate-Based Dental Glass-Ceramics4
The Effect of Bias Voltage and Acetylene Gas Flow Rate on the Wear Behavior of Diamond-like Carbon Coatings on M2 High-Speed Steel4
Interfacial Microstructure and Mechanical Properties of B 4 C/W Functionally Graded Materials by Spark Plasma Sintering3
Sliding Wear Response of Marble Dust Coatings on Mild Steel Substrates3
Prediction of Wear Properties of CaO and MgO Doped Stabilized Zirconia Ceramics with Artificial Neural Networks3
Performance Evaluation of Ceramic Membrane Based Process for Microalgal Biomass Harvesting: Analyzing the Effect of Membrane Pore Sizes, Process Optimization and Fouling Behavior2
Mechanical Properties of Silicon Nitride Ceramics Determined by Microcantilever Tests – A Comprehensive Overview2
Ballistic Resistance of Silicon-Carbide-Based Ceramic and Ultrahigh-Molecular-Weight Polyethylene Composite Armor2
Microstructure and Thermal Shock Resistance of Zr7/8Ti1/8B2-20 vol% SiC Composites Synthesized by Mechanical Alloying and Spark Plasma Sintering2
Doping Fe and Co Induced Modification in the Structural, Optical and Colossal Permittivity of Nb-doped TiO2Ceramics2
Low-Cost Combustion Synthesis, Spectroscopic and Optoelectronic Analysis of Novel Ba2YAlO5:Er3+ Nanomaterials for Competent Illumination Applications2
An Economic Formulation to Elaborate Resistant Technical Porcelains Using Abundant Raw Materials: Thermal and Rheological Properties Characterization2
Influenceof Sm2O3 and CaF2 Concentrationonthe Enhancement of Luminescence and Red Colour in Borosilicate Glass2
Properties of Plasma Sprayed Al2O3-13TiO2 and ZrO2 Blended Coatings on Biomedical Alloy1
Structural Control by Stereolithography Additive Manufacturing and Environmental Material Tectonics1
Effects of AlN Content and Sintering Atmospheres on the Thermal Conductivity of Hot-Pressed SiC Ceramics1
Manufacture of a High Temperature Structural Insulator (HTSI) Using Electrofilter Powders Generated in the Bayer Process1
A Preparative Approach of TiO2-ZrO2 Coating Using Aquo-Based TiO2 Precursor Useful for Light Reflective Application1
Review on CeO2-Based Corrosion Coatings1
Permeability Behavior and Wastewater Filtration Performance of Mullite Bonded Porous SiC Ceramic Membrane Prepared Using Coal Fly Ash as Sintering Additive1
Porcelain Stoneware Tiles Based on Clays Mixture and Recycled Waste Glass Powder: Effect of Soaking Time1
The Effect of Morphology on the Photocatalytic Efficiency of Magnetite-Titania Nanoparticles for Wastewater Purification1
Enhancing Strength Properties of Hydroxyapatite Composites with Bentonite Clay1
Chromium Doped Glasses for Photonic Applications: A Brief Review and Prospects1
Assessment of a Novel Chemical Analysis Technique to Investigate Cesium in Glass by Developing Cesium Bismuth Iodide1
Impedance Spectroscopy Characterization of ZnCo2O4 Ceramics Obtained by the Sol-Gel Method1
Thermoelectric Performance of YSZ Additions to ZnO Ceramics: Processing and Investigation1
Synthesis and Characterization of Hydrothermal Synthesized Ultra-Red CdS 1− x Se 1
Synthesis, Structural and Raman Investigations of PbNi1/3Nb2/3O3 Ceramics1
Mineralogical and Physico-Chemical Characterization of Arslanlar Clay for Potential Industrial Applications1
Effects of SiO2 Addition on Phase Transition and Microstructure Evolution of Alumina Fibers Prepared Using the Sol-Gel Method1
Surface Activation of Titanium Implant by Tricalcium Phosphate Ceramic Based Composite Coating for Bone Tissue Regeneration1
Effect of Non-Plastic Raw Materials Particle Size on Technological Properties of the Single-Fired Wall Tile Bodies1
Investigation of Physico-Mechanical Properties and Multi-Objective Optimization of Industrial Ceramic Tiles Using Response Surface Method: Sintering Temperature and Time1
Preliminary Investigation on the Application of a Semi-Lightweight Mullite Spherical Solid Waste Material in Ladle Permanent Layer1
Effect of BPO 4 -B 2 O 3 Composite Additive on Crystallization and Sintering of Silica Ceramics1
0.039016008377075