Science of Sintering

Papers
(The TQCC of Science of Sintering is 2. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)
ArticleCitations
The effect of molten salt on the mechanical properties and microstructure of CuNiSi alloys with reinforced Fe23
Enhanced microstructural and mechanical properties of Alumix 13 matrix hybrid composites reinforced with B4C and SiC12
Preparation of magnetic surface molecularly imprinting polymers based on glycidyl methacrylate as selective sorbents for aniline removal from aqueous medium11
Assessment of construction and demolition waste application for improving frost resistance in masonry clay units10
Comprehensive optimization of selective laser melting process parameters for microstructure, density, hardness, and tribological performance of pure copper10
Comprehensive characterization of natural bentonite clay: Implications for enhanced performance in ceramics manufacturing10
Evaluating the accuracy of 3D printing of sintered dental metalwork9
Structural and morphological studies on yttrium-doped magnesium aluminate spinel powders synthesized by mixed-fuel solution combustion synthesis approach8
Geochemical evaluation of dolostone deposits in Montenegro: Implications for potential industrial applications7
The microstructural representation and fractal nature intepolation analysis of feldspar6
Oxone® induced textile dyes degradation using cobalt-doped alumina catalyst6
The effect of acrylate on the properties and machinability of alumina ceramics6
Synthesis and mechanical characterization of hydroxyapatite-based biomaterials reinforced with nickel-titanium-magnesium alloys for use in cortical bone implants6
Structural features of near equiatomic FeCo-2V semi-hard magnetic alloy prepared by MIM technology6
Dilatometric and microstructural study of particle and functionally graded composites based on hydroxyapatite and crystalline bioglass6
Understanding the effect of synthesis and sintering temperature on the functional properties of barium titanate/cobalt ferrite composites6
Influence of iron on the mullite formation5
Superparamagnetic properties of nickel ferrite nanocrystals prepared by an organic-phase thermal decomposition5
Investigation of the mechanical properties of concrete incorporating recycled rubber particles5
Electronic properties of BZT nano-ceramic grades at low frequency region4
Effect of graphene nanosheet addition on the microstructure, microhardness, thermal conductivity and melting behavior of a Sn-0.7Cu-based alloy fabricated via powder metallurgy technique4
Investigation of the effects of surface oxide layer on wear and corrosion in NiTi alloys: A mechanical and chemical perspective4
Synthesis of Y2O3 and graphite-added copper-based hybrid composites by powder metallurgy: Mechanical properties and tribological behavior4
The Bridgman method of (BiAs)2 (TeSe)3 bulk single crystal growth by spontaneous nucleation4
Influence of grinding, pressing and sintering of the powder 50.0 wt% Fe, 47.0 wt% BaTiO3 and 3.0 wt% TiO2 on morphology, microstructure, magnetic and electric properties4
Microstructure and orientation - dependent fatigue performance of direct metal laser sintered maraging steel3
Tribological performance of selective laser sintered pa12 sliding bearings under dry sliding conditions3
Photocatalytic activity of novely obtained biobased mandarin peels/TiO2 particles toward textile dye3
Influence of different sintering techniques on the wear properties of Al-15Si-2.5Cu-0.5Mg/B4C composites3
Kinetics of the crystallization process of ferromagnetic Fe65.5Cr4Mo4Ga4P12C5B5.5 bulk metallic glass3
Analysis of the qualitative characteristics of polo shirts made of cotton and cotton/elastane single pike weave before, during and after 60 washing cycles with commercial detergents3
Investigation of Li2O and TiO2 effects on MAS glass-ceramic produced from waste material3
Understanding the sintering behavior of AlCrFeNiTi high entropy alloy via phase field modeling illustration3
Modification of the Ni-NiO-oxidant system by thermo-chemical oxidation with accelerated growth of the p-type dielectric oxide layer, by the action of substituted V2O5 on the system3
Microstructure development in warm upset AM Ti643
The influence of strontium content and sintering temperature on monazite stability3
Comparative study on the tribological properties of direct metal laser sintered and conventionally manufactured Ti6Al4V alloys3
Effects of soda lime glass waste on the physical, mechanical and aesthetics properties of sanitary-ware glazes3
Pyrolytic synthesis of hydroxyapatite from bovine bone: A response surface methodology approach3
Durability of eco-conscious masonry mortars: insights on fire and freeze-thaw resistance2
Effect of different sintering temperatures and atmospheres on the microstructure and mechanical properties of particulate M2 high-speed steel2
Sintered magnesium ferrite particles in decolorization of anthraquinone dye AV 109: Combination of adsorption and fenton process2
Characterization and densification of hot pressed ZrCN-$ \mathrm{ZrO_2} $ ceramics2
Influence of grinding and pressing of the powder 50.0 wt% Fe, 47.0 wt% BaTiO3 and 3.0 wt% TiO2 on morphology, microstructure and magnetic properties2
Electrochemical characterization of carbon-based pyrophyllite modified electrode for the detection of carbendazim fungicide2
Phyllosilicate-based adsorbents decorated with iron oxyhydroxides: Application for lead, chromates and selenites removal2
Cavitation erosion of samples based on cordierite-talc ceramics2
Cavitation erosion damage of pyrophyllite samples reinforced with cordierite, mullite and zirconium-silicate2
Effect of section thickness on cavitation behaviour of selective laser sintered polyamide 122
Extruded hot compacted alumix 431 powder - mechanical properties and microstructure2
Mechanical reinforcement of polyetherimide with electrospun zirconia nanofibers2
Development of porous concrete pavements with waste materials for flood control2
Nb-Cu metallic composite: SPS preparation, microstructure and mechanical properties2
Calcined mullite powder produced from waste clay-diatomite2
Production of Ni-Co-bronze composites with different TiC composition by hot pressing2
Application of artificial neural networks in performance prediction of cement mortars with various mineral additives2
0.19457602500916