OOIR: Observatory of International Research

Papers

(The median citation count of Journal of Strain Analysis for Engineering Design is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-02-01 to 2025-02-01.)

Article	Citations
Representing capabilities of novel semi-analytical triangular plate elements	18
Identification of the 3D crystallographic orientation using 2D deformations	13
Free vibration analysis of bio-inspired helicoid laminated composite plates	12
Validating out of the box: Identifying a campaign of physical tests	11
Dynamic calculation of stress influence law of rubber core sealing surface of the rotating blowout preventer with defects	11
Evaluation of heterogeneous mechanical tests for model calibration of sheet metals	10
Anti-plane analysis of a crack terminating at interface of the isotropic half-planes bonded to intact orthotropic layers	10
Strain gauge placement optimization methodology to measure multiaxial loads of complex structure	10
Study on the calculation method of time-varying meshing stiffness of herringbone gear under the influence of crack-pitting coupling	9
Stress concentration in shape memory alloy sheets with circular cavities: Effects of transformation, saturation, and plasticity	7
Thermodynamical interactions in a double porosity model with diffusion and microtemperatures	7
Numerical investigation of the effect of geometric defects on dynamic frequency responses in body-centered cubic lattice structures	6
Crashworthiness design and enhanced energy absorption of multi-cell thin-walled circular tubes	6
GFRP reinforced high performance glass–bolted joints: Development of a simplified finite element-based method for analysis	6
A complete characterization of THE fracture forming limits in bulk forming by means of an upset geometry sequence	6
Use of a digital image correlation method for full-field shrinkage measurement in injection molding	6
Predictive modeling of spring-back in pre-punched sheet roll forming using machine learning	6
Investigating the influence of the core material on the mechanical performance of a nitinol wire wrapped helical auxetic yarn	6
Effect of initial stress and rotation on magneto-thermoelastic half-space with gravity field and without energy dissipation	6
Strain gauge-based method to determine in-cylinder projectile velocity and gas pressure	5
Numerical study on the dynamic characteristics of the drive shaft system with diaphragm crack	5
A computationally efficient C⁰ continuous finite element model for thermo-mechanical analysis of cross-ply and angle-ply composite plates in non-polynomial axiomatic framework	5
Analysis of finite creep strains in aluminum plates at static and cyclic loading	5
Free vibration characteristics of viscoelastic nano-disks based on modified couple stress theory	5
Nonlocal dual-phase-lag thermoviscoelastic response of a polymer microbeam incorporating modified couple stress and fractional viscoelastic theories	5

Compound influence of surface and flexoelectric effects on static bending response of hybrid composite nanorod	5
Bending analysis of nanobeams based on the integral form of nonlocal elasticity using the numerical Rayleigh-Ritz technique	5
Thermoelastic stress mitigation and weight reduction of functionally graded multilayer nonuniform thickness disc	5
Incorporation of the effect of strain rate in Mie-Gruneisen equation of state for polyethylene	5
Investigating the effect of hot preforming combined with superplastic forming on thickness distribution and forming time of Ti-6Al-4V alloy using finite element analysis	4
Experimental and numerical analysis of residual stresses induced by the manufacturing process of longitudinal welded tubes	4
Effect of porosity and skew edges on transient response of functionally graded sandwich plates	4
Numerical and experimental investigation on critical stresses due to rail cant	4
Influence of discontinuities on the fracture behaviour of CNT reinforced composites subjected to thermo-mechanical load using XIGA	4
Comparative static analysis of functionally graded porous curved beams: Deterministic versus stochastic approaches	4
Investigation of circular aluminium tube expansion by rigid die as energy absorbers using digital image correlation technology	4
Evaluation and optimization of meshless methods to estimation of the 3D-stress intensity factors in mode I–III for fatigue life prediction cracked shaft under uni and multi-axial cyclic loading	4
A computational method for determining the linear elastic properties of 2D aperiodic lattice structures	4
Optimization of design and fatigue simulations for an electric assisted bicycle frame using uniform design and grey relational analysis	3
Enhancing mechanical properties of consolidated nanocrystalline copper powder by means of equal channel angular pressing method	3
Failure mechanics analysis of AISI 4340 steel using finite element modeling of the milling process	3
An extensive study on strain dependence of glass fiber-reinforced polymer-based composites	3
Non-linear analysis of the flexural-torsional stability of slender tropical glulam beams	3
Stability analysis of arbitrary restrained nanobeam embedded in an elastic medium via nonlocal strain gradient theory	3
Industrial application of a low-cost structural health monitoring system in large-scale airframe tests	3
A novel dynamic stiffness matrix for the nonlocal vibration characteristics of porous functionally graded nanoplates on elastic foundation with small-scale effects	3
Dislocations in an arbitrary angle wedge. Part II: Cracks in the wedge	3
Influence of pore shape on impact dynamics characteristics of functionally graded brittle materials	3
Nonlinear temperature dependent and visco-elastic foundation effects on the free vibration of functionally graded sandwich plates with ceramic foam core	3
Compressive strain measurements in porous materials using micro-FE and digital volume correlation	3
Predicting and improving the novel process parameters involved in deep drawing process of Inconel 718 sheet at room temperature using hybrid DNN-SSO approach	3
Dual-phase-lag thermoelastic damping analysis of a functionally graded sandwich micro-beam resonators incorporating double nonlocal effects	3
A new higher-order beam theory for buckling and free vibration responses of laminated composite and functionally graded porous beams	3
On applicability of MQ-RPIM and MLPG meshless methods with 3D extended-enriched base functions for estimation of mode I stress intensity factor and fatigue crack growth in cyclic tensile and bending l	3
Study of dynamic mechanical behavior of 1060-H112 aluminum alloy: Experimental and numerical simulation	2
Influence of anisotropy on creep in functionally graded variable thickness rotating disc	2
Topological study about deformation behavior and energy absorption performances of 3D chiral structures under dynamic impacts	2
Progressive failure prediction of laminated composite thin skew plates under transverse loading using nonlinear strains	2
Effect of porous defects on mechanical behavior of functionally graded materials	2
Evaluation of hetro-stacked target plate response toward different nose shaped projectile impact	2
Shakedown of a plate with a circular hole: An educational problem	2
Effect of different braking conditions on fatigue crack propagation behaviour of train brake disc	2
Applying Anand versus Garofalo creep constitutive models for simulating sintered silver die attachments in power electronics	2
Hole-drilling method eccentricity error correction using a convolutional neural network	2
Geometric contact characteristics of variable hyperbolic circular-arc-tooth-trace cylindrical gear under different machine tool errors and sensitivity analysis for impact factors	2
A custom-made novel design for temporomandibular joint prosthesis using finite element method: Self-pinned TMJ prosthesis	2
The vibration of viscothermoelastic static pre-stress nanobeam based on two-temperature dual-phase-lag heat conduction and subjected to ramp-type heat	2
Optimal design of prestressed bolt thread	2
Flat and rounded contacts: Modelling the effect of a moment with application to fretting fatigue tests	2
Effect of magnetic field and voids on Rayleigh waves in a nonlocal thermoelastic half-space	2
Random load identification of cylindrical shell structure based on multi-layer neural network and support vector regression	2
The α-generalized implicit method associated with Potra–Pták iteration for solving non-linear dynamic problems	2
Analysis of axisymmetric deformation in generalized micropolar thermoelasticity within the framework of Moore-Gibson-Thompson heat equation incorporating non-local and hyperbolic two-temperature effec	2
Approximate methods for contact problems involving beams	2
Creep damage assessment of HR3C austenitic steel by using misorientation parameters derived from EBSD technique	1

Validation of a structural model of an aircraft cockpit panel: An industrial case study	1
Static, buckling, and free vibration responses of functionally graded carbon nanotube-reinforced composite beams with elastic foundation in non-polynomial framework	1
Eliminating eccentricity error in measuring residual stresses via hole-drilling method using strain gauge rosette with five measuring grids: For thin plates using through-holes	1
Wave propagation in a nonlocal microstretch saturated porothermoelastic medium under Moore-Gibson-Thompson heat conduction model	1
Optimization of the sintering temperature, cooling time and grain size parameters to reduce residual stresses of copper-aluminum functionally graded material using response surface methodology	1
Residual stresses in the aluminium alloy 2014A subject to PAG quenching and vibratory stress relief	1
Improvement of process control in sheet metal forming by considering the gradual properties of the initial sheet metal	1
Research on the automatic modeling and performance prediction of plain-woven composites based on beam elements	1
Thermoelastic transient memory response analysis of non-localized nano-piezoelectric plates based on Moore-Gibson-Thompson thermoelasticity theory	1
Equal channel angular pressing of wire-formed Al6063 by PU rubber-assisted procedure	1
Indenter misalignment in impression creep test: Uncertainty, correction and recommendation	1
Using text as a native speckle pattern in digital image correlation	1
A novel multiaxial fatigue life prediction model based on the critical plane theory and machine-learning method	1
Non-contact strain measurement to eliminate strain gages in vibration-based high cycle fatigue testing	1
Evaluation of Monkman–Grant strain as a key parameter in ductility exhaustion damage model to predict creep rupture of grade 92 steel	1
Revisiting the ring hoop test in additively manufactured metal tubes	1
Application of undercut and FGM to mitigate stress gradients in cylindrical contacts	1
A novel approach to envisage effects of boron in P91 steels through Gleeble weld-HAZ simulation and impression-creep	1
Research on high cycle fatigue damage characterization of FV520B steel based on the nonlinear Lamb wave	1
An integrated experimental and finite element approach for wrinkling limit prediction of Inconel 718 alloy at elevated temperatures	1
Fractional dual-phase-lag thermal-mechanical response of an functionally graded spherical microshell with size-dependent effect	1
CGA: An image processing based software for surface strain analysis in sheet metal forming	1
Methods for measuring friction-independent flow stress curve to large strains using hyperbolic shaped compression specimen	1
Nonlinear dynamics of flexible diaphragm coupling’s rotor system during maneuvering flight	1
The vibration of thermoelastic silicon nitride Nanobeam based on green-naghdi theorem type-II subjected to mechanical damage and ramp-type heat	1
Application of acrylic plates as load cell for detecting strain and force in structures	1
Finite element modeling to explore static bending responses of four-layer FG beam structures considering sliding motions	1
Coupled effects of surface interaction and damping on electromechanical stability of functionally graded nanotubes reinforced torsional micromirror actuator	1
Research on elasticity behavior of Ni-Ti shape memory alloys using the reproducing kernel particle method	1
Comparison of theoretical approaches to determine the stresses in surface mounted permanent magnet rotors for high speed electric machines	1
Determination of dynamic material properties using laser measurement technique in split Hopkinson pressure bar	1
Analytical modeling of through depth strain induced by deep rolling	1
Research on the stability analysis of milling of thin-walled parts based on the dynamic characteristics	1