OOIR: Observatory of International Research

Papers

(The TQCC of Journal of Electrostatics is 6. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-04-01 to 2024-04-01.)

Article	Citations
Comparative study on the contact-separation mode triboelectric nanogenerator	28
EHD gas pumping – A concise review of recent development	23
Experimental study on electrohydrodynamic flows of a dielectric liquid in a needle-plate configuration under direct/alternating current electric field	21
Improved detachable electrodynamic cleaning system for dust removal from soiled photovoltaic panels	21
Effect of relative humidity on dust removal performance of electrodynamic dust shield	18
A modification of the phase-field method to simulate electrohydrodynamic processes in two-phase immiscible liquids and its experimental verification	14
High-efficient removal of airborne oil mist in a wire-plate electrostatic precipitator	13
Optimizing electrostatic cleaning for dust removal on gecko-inspired adhesives	13
Evaluation of spark discharge	13
Effect of ambient air relative humidity on the triboelectric properties of Polypropylene and Polyvinyl Chloride slabs	13
Finding a low cost energy multi-DBD plasma actuator for natural heat transfer enhancement in a vertical duct	13
An explicit CFD model for the DBD plasma actuators using wall-jet similarity approach	13
Real-time measurement of droplet size and its distribution of an air-induced air-assisted electrostatic nozzle	12
Numerical study of micro-scale EHD conduction pumping: The effect of pump orientation and flow inertia on heterocharge layer morphology and flow distribution control	12
Large eddy simulation of electrostatic effect on particle transport in particle-laden turbulent pipe flows	12
Pulsed electric fields act on tryptophan to inactivate α-amylase	12
Study on charge characteristic of melt-blown polypropylene electret fabric by hydrocharging technique	11
Experimental characterization of electric potential uniformity at the surface of polymer plates corona charged by multiple-row needle-type electrodes	11
Two-species modeling of electrohydrodynamic pump based on surface dielectric barrier discharge	11
Fair weather electric field meter for atmospheric science platforms	10
Numerical modeling of particle motion in traveling wave solar panels cleaning device	10
Effect of barbed tubular electrode corona discharge EHD flow on submicron particle collection in a wide-type ESP	10
A parametric study of electrodes geometries for atmospheric electrohydrodynamic propulsion	10
Performance of non-thermal plasma reactor for removal of organic and inorganic chemical residues in aqueous media	10
Lightning to earthed structures: Striking distance variation with stroke polarity, structure geometry and altitude based on a theoretical approach	10

An experimentally validated computational model to predict the performance of a single-channel laboratory-scale electrostatic precipitator equipped with spiked and wire discharge electrodes	10
Hybrid electrostatic filtration system for fly ash particles emission control	10
Simulation and measurement of charged particle trajectory with ionic flow in a wire-to-plate type electrostatic precipitator	9
Effect of a floating conductor on discharge characteristics of a long air gap under switching impulse	9
Electric force between a dielectric sphere and a dielectric plane	9
Analysis of electrohydrodynamic air flow induced by DC corona field in wire-to-plane electrode system	9
Numerical simulation of evaporating charged sprays in spray chilling	9
Numerical study of coalescence and non-coalescence of two conducting drops in a non-conducting medium under electric field	8
Measurement of the charge distribution deposited on a target surface by an annular plasma synthetic jet actuator: Influence of humidity and electric field	8
Analysis of augmented droplet transport during electrowetting over triangular coplanar electrode array	8
Oxidation energy efficiency in water treatment with gas-phase pulsed corona discharge as a function of spray density	8
Correlation of antibacterial performance to electrostatic field in melt-blown polypropylene electret fabrics	8
A uniformly charged circular disk with an anisotropic Coulomb interaction potential	8
A new grounding cake to improve the safety performance of grounding systems	8
Experimental studies on the effect of electrostatic boundary conditions and frequency on the performance of a trigrid electrostatic coalescer	8
Traps energy distribution in Kapton HN polyimide films through surface potential decay model under humidity conditions	8
EHD gas pump in a square channel with electrodes mounted on one wall	8
Increasing force generation in electroadhesive devices through modelling of novel electrode geometries	7
Experimental investigation on correlation between fast-front lightning current and the resultant arc channel luminosity	7
Selective oxidation of methane to methanol by NTP plasma: The effect of power and oxygen on conversion and selectivity	7
Study on degradation diagnostic method for silicone rubber	7
An equivalent discharge model of electrostatics spark	7
Experimental study on the final jump phase in long air gap discharges	7
Electrostatic charge generation on material surfaces from the evaporation of liquids	7
Mechanical properties and space charge behavior of thermally aged polypropylene/elastomer blends	7
The role of the electrode geometry on the dielectrophoretic assembly of multi-walled carbon nanotube bundles from aqueous solution	7
Effect of mixture properties on size-dependent charging of same-material dielectric grains	7
Effect of monomer concentration on adhesive strength of PTFE films treated with atmospheric-pressure nonthermal plasma graft polymerization	7
The charging characteristics of particle–particle contact	7
Experimental analysis of the attraction force applied on metal particles using a double-side electrical curtain	7
Design of charge-sensitive and current-sensitive preamplifiers for electrostatic sensor	7
Effect of ageing of monoesters and mineral oil on the propagation of creeping discharges	6
Flow induced by an EHD gas pump with secondary emitting electrodes	6
Estimating droplet charge in numerical simulations of charged sprays	6
The impact of electric field on the demulsification efficiency in an electro-coalescence process	6
Experimental investigation on the dynamic behavior of small droplet in a uniform DC electric field	6
Cost-effective fabrication approaches for improving output performance of triboelectric energy harvesters	6
Accumulation of spatial charge on the surface of protecting coatings used against the penetration of high frequency electromagnetic fields	6
Oxidation of ubiquitous aqueous pharmaceuticals with pulsed corona discharge	6
Space charge evolution and its effects on electrical tree degradation in silicone rubber at varied temperature under polarity reversal voltage	6
Evaluating the electrostatic charge transfer model for particle-particle interactions	6
Experimental investigation of the electrification of wind turbine blades in fair-weather and artificial charge-compensation to mitigate the effects	6
Study on the effects of electrostatic force and spray characteristics in spray cooling of vertical hot strip	6
A theory for like-charge attraction of polarizable ions	6
Decay of electrostatic charge on surfaces due solely to gas phase interactions	6
Electrical charging of bioceramics by corona discharge	6
Nonlinear potential field in contact electrification	6
A review of particle transport and separation by electrostatic traveling wave methods	6
Direct observation of electric charges at solid/liquid interfaces with the pressure-wave-propagation method	6
Discharge characteristic of barbed electrodes in electrostatic precipitator	6

Experimental characterisation of positive creeping discharges propagating along an insulating surface immersed in vegetable and mineral oil	6
Electrostatic powder attraction for the development of a novel recoating system for metal powder bed-based additive manufacturing	6