Surface Engineering

Papers
(The TQCC of Surface Engineering is 5. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-09-01 to 2025-09-01.)
ArticleCitations
Structure and properties of aluminum alloy composite conversion coating76
Tailoring Er 3+ doped ZnTiO 3 ceramic surfaces for high color purity green-emitting display device applications30
Surface modification of urinary catheters28
Study on surface properties of UHMWPE/Hap composite coating on Ti6Al4V20
Laser surface texturing of dies in strip drawing of DP600 steel sheet19
Hot corrosion behavior of Y 3 NbO 7 as thermal barrier coating material16
Investigation of tribological and corrosion performance of electroplated hard chromium coating on 17-4 PH steel16
Effect of inorganic silicate sealing treatment on corrosion behaviour for HVAF sprayed Fe-based amorphous coatings16
Effect of chromium–titanium on corrosion and erosion of HVOF coating14
Alteration in Ti6Al4V implant surface properties with micro textures density14
Inverse method of eigenstrain determination of laser shock peening13
Characteristics of GaTiZnO coatings deposited by magnetron sputtering13
Robust long-lasting antifogging coatings prepared by a facile method13
Influence of different modes of microarc oxidation of titanium on the electrochemical properties and surface morphology of the obtained coatings12
Study on the wear resistance of micro-arc-oxidised ceramic films on the surface of TC4 titanium alloy oil well tubing in the Ordos Basin12
Effect of annealing on the wear performance of MAO coatings11
Modified polymer nanopillars array for enhanced light trapping on large area11
Effects of aluminised-coating on microstructure and properties of Ni–Co-base superalloys10
Mechanical optimisation of Ni coatings produced by low-pressure cold spray10
Ductile–brittle indentation fracture transitions in hard coatings10
Influence of toolpath strategies during laser polishing on additively manufactured biomaterials10
Effect of bias voltages on microstructure and mechanical properties of (AlCrNbSiTi)N high entropy alloy nitride coatings deposited by arc ion plating10
Investigation of electrodeposited copper layer with island twinning structure on Zr substrate10
Measurement methods and fractal dimensions of blast-cleaned steel substrates10
A novel approach of thick coating through selective jet electrodeposition process9
Pinecone-Structured ZnO microparticle coatings: A superhydrophobic approach for scale prevention on steel surfaces9
In-situ-growth of hard-coating, its impact on mechanical performances in cemented-carbides9
Investigating coating adherence on S275JR carbon steel under cyclic corrosion9
Laser cladding Al/Ni composite coating and its tribology performance8
Evaluation of Ni-Co/TiO2-CeO2 nanocomposite coatings fabricated by electro-co-deposition8
Effect of burnishing on HVOF coated boiler steel against hot corrosion in actual boiler environment8
Corrosion resistance of Si-Zn composite coating on AZ31 alloy8
A novel criterion to identify coatings’ adhesion8
Improvement of X-ray response of CZT films by post-annealing8
Structural investigation of ZrN+Si3N4 thin films co-deposited by magnetron sputtering8
Gradient Cr–AlN composite coating prepared on alumina-forming austenitic steel8
Powder-infused arc cladding for enhanced mechanical and corrosion performance8
Effect of oxidation time on black MAO coatings8
A new approach for constructing rough structures to fabricate superhydrophobic Ni–B/graphene oxide (GO) coating8
Anti-corrosive superhydrophobic coatings fabricated by a simple dipping method8
Wear and corrosion behaviour of the cryogenically treated tungsten carbide coatings8
Microstructure and surface quality of SLM printed miniature helical gear in LSPwC7
Understanding the fundamentals of TiO2 surfacesPart II. Reactivity and surface chemistry of TiO2 single crystals7
Enhancing the hydrophobicity of Ti–6Al–4V through multi-level electrical discharge texturing7
Al-Cr-Si-N coating: Substrate temperature effect on mechanical and scratch behaviour7
Influence of pH on the electroless Ni-P plating of SiC particles7
Oleophobic coatings7
Hot corrosion and cyclic oxidation effect on deep cryogenically treated nimonic-90 superalloy7
Self-healing coatings7
Effect of titanium interlayer configurations on residual stresses and performance of titanium/titanium nitride multilayer coatings7
The evolution and future of polymer cold spray technology7
Influences of Sc(NO3)3 on characteristics of micro-arc oxidation coatings7
Core shell particles7
Enhanced corrosion resistance of CoCrMo by laser-based surface modification6
Microstructure and wear resistance of cold sprayed CoCrFeNi HEA coatings: Influence of powder particle size and spraying temperature6
Surface modification of tantalum6
Characteristics of reduced graphene oxide (rGO) mixed HVOF-sprayed nanostructured coatings6
Improvement of AISI 316L laser cladding properties by high-frequency vibration process6
Effect of Cu on microstructure and properties of Co2CrFeNiMnCux high-entropy alloy coatings prepared by laser cladding6
A green vanadium-based formulation for the conversion of steel6
Analysis of adhesion strength and residual stresses developed by the EDC process6
Ni-P SiC composite coatings on piston rings by plate and bumper technique and its tribological properties6
Electric discharge coating on graphite using W–Cu sintered tool6
Surface modification of stents6
Non Halogenated Flame Retardants6
Wear behaviour of different nano particles coating on Al6061 substrate6
Enhanced tribological performance and nanostructuring speed on AlTiN by beamshaping technology6
Comparative erosion performance of HVOF and LVOF sprayed NiCrSiBCFe-WC-Co coating5
Tribo-corrosion maps of thermally sprayed cemented carbide coatings: A critical review5
Examination of the metallization behaviour of an ABS surface5
Tribocoats for biomedical applications: Nanoscale mechanical stability5
Synthesis of TiO2 coatings by thermal oxidation with a suitable cooling process for improved wettability5
Acrylic-based monocoat eco-friendly, anticorrosive coating for cathodic electrodeposition5
Protection of AA2024 alloy against wear and corrosion by HVAF sprayed AlCuFe coating5
Effects of Er2(SO4)3 doping on characteristics of MAO coating5
Effect of the Nb content on the microstructure evolution and properties of the CrFeCoNiNbx layers prepared by laser cladding5
High-temperature wear behaviour of ZrC/NbC-reinforced CrMnFeCoNi coatings5
Synthesis and self-cleaning properties of superamphiphobic coatings based on burr-like copolymer particles5
Tribological CCF-PEEK transfer film growth on cutting tool coating5
Corrosion fatigue behaviour of electrospun PCL/HA coated magnesium biocomposites5
Tailoring Ti Grade 2 and TNTZ alloy surfaces in a two-step mechanical–chemical modification5
Effect of In2(SO4)3 on characteristics of Al–Li alloy MAO coating5
Electrical discharge micro-texturing using compound tool electrodes for tribological and wettability applications5
Tungsten inert gas-assisted surface modification of 1045 steel with SiC particles5
Coatings to break the ice5
Crack, microstructure, and phase-evolution in pulsed-wave LMD of NiCoCrAlY coating5
Electron beam hardening of nanobainitic steel5
Understanding the fundamentals of TiO2surfaces. Part I. The influence of defect states on the correlation between crystallographic structure, electronic structure and physical properties of5
Long-term oxidation of MoSi2-modified HfB2–SiC–Si/SiC–Si coating at 1700°C5
Investigation of tribological and corrosion properties in ceramic/PTFE coating5
Electrochemical behaviour of sputter-coated titanium films on AZ31 magnesium alloy5
0.35014390945435