OOIR: Observatory of International Research

Papers

(The H4-Index of Chemical Engineering Research & Design is 46. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-01-01 to 2026-01-01.)

Article	Citations
Effect of operating condition on the properties of ectoine particles for improving the purification process	150
Effect of bubble-to-oil size ratio on dynamic behavior in flotation	144
A new method for measuring the uniformity of multiphase mixing in direct contact heat exchangers based on the EMT system	131
Contents	123
Columns with parallel streams applied to the steam stripping of edible oils	119
Industrial process fault diagnosis based on video recognition and multi-source information fusion	116
Visualization experiments of a solid cylinder suspended by laminar flow	107
Review of confined swirling flows and bluff body impacts on flow and heat transfer characteristics	107
Dynamic characteristics of pollutant emissions from CFB boilers during periodic fire banking and start-up	98
Fabrication of CFOx-PVDF catalytic membrane for removal of dyes in water and its mechanism	95
Cost-effectiveness analysis in the manufacture of allogeneic human induced pluripotent cells in Japan by agent-based modeling	95
Artificial neural networks modeling ethanol oxidation reaction kinetics catalyzed by polyaniline-manganese ferrite supported platinum-ruthenium nanohybrid electrocatalyst	95
A modeling analysis on industrial radial-flow packed-bed reactors for the catalytic dehydrogenation of long-chain normal paraffins: Appraisal of the modeling approach	95
Removal of hydrocarbon pollutants from aqueous media using hydrophobic cellulose-based adsorbents	88
Modified emulsion polyvinyl chloride membranes for enhanced antifouling and dye separation properties by introducing tungsten disulfide (WS2) nanosheets	88
Numerical simulation on liquid-solid two-phase erosion characteristics of pipe bends with different bend angles	80
A novel approach for modeling and simulation of vibrating fluidized bed dryers: Industrial scale case study	77
Double tube configuration of atmospheric pressure plasma jet for deposition of organic coatings in open air	73
Blending in unbaffled and baffled mechanically agitated vessels – Effect of Reynolds number and liquid height	71
Investigation on structural optimization of rotational hydrodynamic cavitation reactor with a tapered rotor for organic dyes degradation	68
Dynamic control analysis of energy-efficient side-stream extractive distillation process for separating close-boiling mixture	65
Design and characterization of Kenics static mixer crystallizers	64
Dehydration of isopropanol by poly(vinyl alcohol) hybrid membrane containing oxygen-plasma treated graphene oxide in pervaporation process	64
Continuous degradation of 1,4-dioxane by the combination of a stripping column and photo-Fenton reaction in a continuous stirred tank reactor	61
A cluster-based drag model of rough sphere for the simulation of fast fluidization	60

Synthesis of mesoporous γ-alumina from a low-grade boehmite ore: Effect of thermal/chemical processing order on physico-chemical characteristics of adsorbent and regeneration of used transformer oils	60
A solar-driven CPC photoreactor for decomposition of emerging contaminants in wastewater: Modeling and optimization	60
A porous-crust drying model for a single dairy droplet	60
Contents	59
Flux decline in crossflow ultrafiltration-based diafiltration process for lignin recovery from a deep eutectic solvent comprised of lactic acid and choline chloride	55
Hydrodynamics aspects of asymmetric rotating impeller columns at different scales	55
Experimental investigation of the flow properties of layered coal-rock analogues	54
Characterization and optimization of a used cooking oils collection chain – Study case Bogotá, Colombia	52
A hybrid drag model for studying hydrodynamics in a 2D gas-solid tapered fluidized bed	51
Effect of fluidized bed shapes on gas-solid fluidization characters and flow regime transition	51
Treatment of lignin enriched paper industry wastewater by electrocoagulation: Modelling approach and economic evaluation	51
Biochar-supported zinc ferrite for H2S removal at room temperature in anaerobic conditions	50
Structural optimization of hydrocyclone coalescer based on response surface method	50
Liutex-based flow structure characterization in vibrating downhole hydrocyclone for oil-water-sand multiphase systems	49
Effects of process parameters on preparation of Ti@SiO2 particles during fluidized bed chemical vapor deposition via design of experiments	48
Pilot plant reactor for ammonia synthesis – Computational fluid dynamics analysis with experimental validation	48
Investigation of droplet pairs’ movement under the electric field generated by matrix electrodes	48
Wiped film evaporator with a roller wiper and an internally mounted condenser for the recovery of TBP and n-DD from degraded PUREX solvent	47
Continuous manufacturing based paradigm shift in pharmaceuticals production and current regulatory framework	47
Machine learning-driven prediction and optimization of norfloxacin removal efficiency and energy consumption in plasma process system	46
Intensification of industrial wastewater treatment using hydrodynamic cavitation-based hybrid ternary advanced oxidation processes	46
Aeration model for submerged membrane bioreactor – Characterization, oxygen transfer rate, pollutant removal, and energy consumption	46
On flow close to cavern boundaries in yield stress fluids - revisited. Current interpretation	46
Evaporation effects on residence time in wiped film evaporators with roller wipers	46