OOIR: Observatory of International Research

Papers

(The H4-Index of Composite Structures is 69. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Editorial Board	459
Editorial Board	185
A two-layered cross-ply laminate model for a single-ply satin woven fabric composite under thermal loads	175
Editorial Board	170
Mechanical investigation of inverse FML under mode II loading using acoustic emission and finite element method	151
A two-dimensional model to analyze the static and dynamic mechanical behavior of multilayered shell structures	148
Editorial Board	145
Editorial Board	131
A numeric-experimental study on damage parameters for crack propagation using the Finite Element Method Updating approach	129
A topology optimization framework for 3D phononic crystals via the method of successive iteration of analysis and design	128
Influence of boehmite nanoparticles on moisture absorption and temperature effects in GFRP used for wind turbine blades	127
Influence of fibre undulation on the biaxial behaviour of filament-wound FRP tubes in concrete-filled FRP tubes	126
Dynamic concurrent topology optimization and design for layer-wise graded structures	124
Stiffness-driven design and optimization of a 3D-printed composite prosthetic foot: A beam finite Element-Based framework	121
A finite element-based continuum damage model for mechanical joints in fiber metal laminates under static and fatigue loading	120
A coupled 3D morphological reconstruction method for point microcrack defects in Si3N4 ceramic bearing rollers	120
Enhanced near-field radiation of acoustic-actuated antennas using embedded magnetoelectric composites	119
Near-zero thermal mismatch flexure metastructure with high-resonant frequency	116
Shear behavior of RC beams strengthened with BFRP grid-reinforced EGC	105
Multiple blast resistance enhancement through negative-mass meta-honeycombs with multi-resonator	105
Laser-induced heating, property changes, and damage modes in carbon fiber reinforced polymer matrix woven composites	104
An efficient micromechanical framework for elastic and viscoelastic properties prediction of unidirectional continuous fiber-reinforced polymers with microvoids	101
Piecewise power law approximation of the interlayer relaxation curve for the long term viscoelastic fractional modeling of laminated glass	101
High-speed penetration of laminated alumina ceramic/polymethacrylimide foam composite: in situ synchrotron X-ray imaging and mesoscale modeling	98
Experimental and numerical failure analysis of thin-walled composite plates using progressive failure analysis	98

Anisotropic elastoplastic constitutive modeling of additively manufactured Strut-Based lattice structures	96
Differential viscoelastic model with independent shift factors for thermorheologically complex polymers and composites	96
Analytical modeling of axial compressive behavior of geopolymer concrete columns confined with FRP-bamboo winding tubes	95
Aeroelastic optimization design of composite materials blade based on RBF/ROM and CCA reliability analysis	94
Investigations of horizontal rotation at the support of bending beams as proof of global distortional buckling mode	94
Multiscale analysis of open holes and fasteners in CMC structures with the Generalized Finite Element Method	92
Dynamic crushing performance of foam-filled periodic hybrid cellular structures	91
A carbon fiber lamina electrode based on macroporous epoxy with vertical ion channels for structural battery composites	90
Study of mixed-mode fracture in functionally graded material using an adaptive phase-field fracture model	89
A hierarchical analytical model for twisted yarn reinforced plant fiber composites considering dual-scale filler content, porosity and local aggregation effect	87
Compressive response of bio-strengthened engineered cementitious composites (ECC) with self-healing characteristics	85
Multi-axis 3D printing of L-shaped honeycomb sandwich structure with continuous carbon fiber reinforced composites	85
A constitutive model for rate-dependency analysis of open hole woven composites under compression loading	84
Study on stable configurations and snap through of the rectangular VS bi-stable laminates with curvilinear fiber alignment	84
An efficient model for predicting complex delamination front of elastic coupling laminates	82
A novel advanced block assembly method with 3D printed channel systems	81
Multiscale modeling of carbon nanotube fibers. Interpretation of microscopic properties from tensile tests	80
Investigation of the evolution and movement of volatile bubbles in the process of curing polyimide composites by in-situ observation	80
Navigating the degree of multistability and snap-through in piezoelectrically actuated series-connected unsymmetrical laminates	80
A comparative study of tensile fatigue life in various flexible-oriented three-dimensional woven process structures based on finite element models	80
Wet collapse mechanism of steel-reinforced flexible pipe structures under curvature effect: Physical experimentation and numerical simulation	79
Study on the mechanical properties and ballistic resistance of interface-modified fabrics with environmentally friendly shear thickening liquid	77
Influence of preheating on ultrasonic welding of CF/PEEK composite laminates	76
Development of a geometric modeling strategy for the generation of representative unit cells in 2D braids	76
Enriched embedded-fiber crack-bridging element for XFEM fracture and pullout analysis of composites	75
A Spectro-geometric solution of dynamic characteristics of submarine-like structures	75
Tolerance modelling of vibrations of thin functionally graded cylindrical shells	75
In situ growth of micro-nano structured black oxide coating on steel with excellent superhydrophobicity and corrosion resistance	75
An elastoplastic mechanical-thermal model for temperature rise simulation of two-dimensional triaxially braided composites under quasi-static loads	75
Numerical homogenization with FFT method for elastic composites with spring-type interfaces	74
Monotonic and cyclic compression behavior of axially loaded FRP-confined concrete-encased cross-shaped steel columns	74
Dynamic mechanical behavior of basalt-polyethylene fiber-reinforced concrete after chloride attack	74
Multiscale topological design of coated structures with layer-wise bi-material lattice infill for minimum dynamic compliance	73
Fluid-structure interaction analysis of nonlinear flapping dynamic behaviors of variable stiffness composite laminated plates in viscous flows	73
A mixed finite element model for FRP-strengthened RC slabs based on sequential linear analysis	72
Multimodal characterization of adhesion within thermoplastic welded composites using Lamb waves	72
Rve-based isogeometric analysis of thermo-electro-mechanical band gaps in piezoelectric composite phononic crystals	72
An improved contact parameter model with elastoplastic behavior for bolted joint interfaces	72
Callus geometry estimation for tibial fractures with flexible composite intramedullary nail	71
Thermomechanical in-plane dynamic instability of asymmetric restrained functionally graded graphene reinforced composite arches via machine learning-based models	70
A unified Ritz framework for free vibration analysis of shells	70
Theoretical and numerical study on buckle propagation in sandwich pipelines subjected to external pressure	70
M-VCUT level set method for the layout and shape optimization of stiffeners in plate	70
SIMP Phase-field topology optimization framework to maximize fracture resistance in FGMs	70
Bio-inspired nacre-like structures for enhanced blast resistance	69
A comparative study on conventional drilling and ultrasonic vibration-assisted drilling of CF/PEEK	69
On dynamics of origami-like structures: Necessity of enhanced models	69