Journal of Fluids Engineering-Transactions of the Asme

Papers
(The median citation count of Journal of Fluids Engineering-Transactions of the Asme is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)
ArticleCitations
Effect of Trailing Edge and Span Morphing on the Performance of an Optimized NACA6409 Wing in Ground Effect48
Hydrodynamic Forces and Flow Characteristics Around a Rigid Helical-Shaped Metallic Chip in Shear Flow Near a Plane Wall41
Stability of Thermal Convection in Two Superimposed Miscible Viscous Fluids Under Gravitational Modulation38
Mechanism of Low-Frequency Oscillation in the Compressor Corner Region and Its Deterministic Impact on Loss Generation31
Controlled Bubble Formation From a Microelectrode Single Bubble Generator30
Switching Events of Wakes Shed From Two Short Flapping Side-by-Side Cylinders29
Fluidic Thrust Vector Control of Aerospace Vehicles: State-of-the-Art Review and Future Prospects29
Cavitation Flows Past a Rotating Circular Cylinder27
A Drag Model for Rough Surfaces Learned Using Feature Importance-Informed Symbolic Regression26
A Novel Method to Achieve Fast Multi-Objective Optimization of Hydrostatic Porous Journal Bearings Used in Hydraulic Turbomachine24
Experimental and Computational Fluid Dynamics Uncertainty Estimation in Solid Particle Erosion23
Particle Image Velocimetry in a Centrifugal Pump: Influence of Walls on the Flow at Different Axial Positions23
Impact of Flow Rate on Turbopump Inducer Blade-to-Blade Interaction During Local Cavitation Instability21
PeleMP: The Multiphysics Solver for the Combustion Pele Adaptive Mesh Refinement Code Suite21
Effect of a Turbulence Grid on the Compressible Flow of an Organic Vapor20
Validation of a Human Upper Airway Computational Fluid Dynamics Model for Turbulent Mixing19
Design and Implementation of an Experimental Test Bench for the Study of Active Flow Control in Scale Wind Turbines18
New Electro-Active Polymers-Based Plasma Actuators for Simultaneous Flow Control and Ice Protection17
A Method to Determine Bubble Distribution in Liquid Using Data of Inverse Acoustical Scattering17
Thermal Protection Analysis of Hypersonic Reentry Nose Cone With Multirow Disk Spike Using Lateral Single/Multijets: A Computational Investigation17
Suppression of Cavitation Instabilities in an Inducer by the Circumferential Groove With Swirl Breakers15
The Measured Flow at the Inlet of a Francis Turbine Runner Operating in Speed No-Load Condition15
A Solution Method for the Filtered Lifting Line Theory15
Spray Entrainment Coefficient Modeling for High Injection Pressure Based on Entrainment Velocity and Force Analysis14
Orifice Jet Curvature and Its Interaction With a Row of Short Pin-Fins14
Data-Driven Dynamical System Models of Roughness-Induced Secondary Flows in Thermally Stratified Turbulent Boundary Layers14
A Study of the Velocity Field During Mitigation of Vortex Breakdown in Model Francis Turbine at High Load14
Unified Approach for Damping Rate of Transient Laminar Flow: Experiments, Computational Fluid Dynamics, and One-Dimensional, and Global Models14
A Compound Droplet Undergoing Thermocapillary Migration Passing Through a Constricted Tube14
Experimental Investigation Into Cavitation Erosion Characteristics of Stainless Steel Caused by Laser-Induced Bubbles13
Hydrodynamic Investigation of a Hybrid-Bladed Savonius Hydrokinetic Turbine—Computational Fluid Dynamics and Taguchi Optimization Approaches13
Direct Numerical Simulation of Involute Channel Turbulence13
A Wind Speed Forecasting Method Using Gaussian Process Regression Model Under Data Uncertainty13
Actuation Modeling of a Microfluidically Reconfigurable Radiofrequency Device13
Assessing the Effect of Coriolis Acceleration on the Coherent Structures in the Wake of a Wind Turbine Using Dynamic Mode Decomposition13
Research on Noncavitation Noise of Axial-Flow Pump Jet Propulsor Impellers and Biomimetic Noise Reduction Design12
Experimental Study of Two-Phase Flow-Induced Vibrations in Pipelines Under Varying Flow and Burial Conditions12
Correlations Describing Laminar Hydrodynamic Development in a Circular Pipe11
Loss Assessment Method of Fluid Curtain–Labyrinth Seals and Action Mechanism of Key Parameters on Seal Performance in a Turbine Rotor Tip11
Numerical Analysis of the Drag Reduction Performance of a Double M-Ship Boat With Stepped Planning-Air Coupling11
Analysis of Flow Maldistribution in Compact Heat Exchangers11
Aerodynamic and Aeroacoustic Simulations of a Wind Turbine Airfoil Employing a New Transitional IDDES Method10
Numerical Investigation of Supersonic Air-to-Air Ejectors Including Design Effects on Entrainment Efficiency10
Swirl Effects On Gas-Liquid Upward Vertical Pipe Flow10
Effect of Tip-Mounted Propeller and Trailing-Edge Flap on Wing's Lift and Drag Coefficients and Vortical Wake10
Cavitation Characteristics Analysis of a Reciprocating Cryogenic Pump During Fluid Inlet Process Based on Computational Fluid Dynamics Simulation9
Numerical Assessment of Steady-State RANS Models for Predicting Boundary-Layer Transition, Separation, and Wake Characteristics of Horizontal-Axis Wind Turbines9
Mitigating Sediment Erosion of a Centrifugal Pump Impeller Using a Passive Flow Control Method9
Flow Control Around a Cylinder With a Perforated Cylinder9
Influence of Nozzle Convergence Angle on the Flow Characteristics of Synthetic Jets in a Turbulent Crossflow Boundary Layer9
Effect of Perforation on Vortex Characteristics of a Microvortex Generator Mounted on a Flat Plate9
Tip Leakage Flow Structures and Its Influence on Cavitation Inception for a NACA0009 Hydrofoil9
Leak-Rate Through Carbon Brush Seals: Experimental Tests Versus Predictions From a Porous Medium Approach9
Flow Through a Passage With Scaled Additive Manufacturing Roughness Representing Different Printing Orientations9
Unsteady Flow and Pressure Pulsation Characteristics in an Ultra-High-Speed Centrifugal Pump Considering the Weak Compressibility Effect8
The Influence of Vortex Flow in the Dispersed Phase on Droplet Formation Dynamics8
Numerical Studies of Bubbles in Swirling Channel Flows8
Analytical Solution to Time-Periodic Electro-Osmotic Flow of Generalized Maxwell Fluids in Parallel Plate Microchannel With Slip-Dependent Zeta Potential8
Novel Calculation Method for Windage Power Loss of Double-Helical Gear Transmission8
Vortex Identification Method Based on Topological Analysis and Velocity Gradient Invariance8
Simulative Quantification of the Supersonic Discharge Process of Cold Gas Airbag Inflators8
Analysis and Modeling of Turbulence Anisotropy of a Swirled Hot Streak Flow8
Stability and Energy Balance Analysis of Axisymmetric Boundary Layer: Effects of Oblique Nonuniform Suction and Injection8
Boundary Layer Investigations for Primarily Axial Flow Over a Stationary and Transversely Oscillating Cylinder8
Extending the Pressure-Time Method to Pipe With Variable Cross-Section With Three-Dimensional Numerical Simulations8
Influence of Scallops on Windage Loss and Flow Characteristics in Disk-Type Gap8
Experimental Demonstration of a Topology Optimization Method to Generate a Capacity-Specific Device With Cavitation Resistance for Control Valve Applications8
Predicting Erosion in a Counter-Rotating Fan Under Different Operating Conditions8
Characterizing the Effect of Sinusoidal Wall Amplitude on Turbulent Wall Jet Flow Parameters8
Passively Enhanced Vortex-Induced Vibration Response of Side-by-Side Cylinders in Turbulent Flow7
Research on the Correlation Between Structural Deformation and Flow Field Characteristics of Ejector Baffle Based on Fluid–Structure Coupling Analysis7
Special Issue Dedicated to the 2025 ASME Turbo Expo on Wind and Renewable Energy Research7
Two-Stage Fluidic Valve With SparkJet Actuation for Flow Control7
Static and Dynamic Time Filtering Techniques for Hybrid RANS-Large Eddy Simulation of Non-Stationary Turbulent Flows7
Derivation of “Double-Loop” Theory and Mechanism of Cavitation-Vortex Interaction in Turbulent Cavitation Boundary Layer7
Three-Dimensional Numerical Investigation of Bubbles Growing and Merging in Superheated Nucleate Boiling7
An Aerodynamic Investigation of the Last-Stage Turbine in an Upgraded Gas Turbine7
Pulsed Blowing for Amplifying Unsteady Lift on a Cylinder7
The Influence of Oblique Tunnel Portals and Blockage Ratio on the Aerodynamic Performance of Urban Rapid Rail Tunnels7
Experimental and Simulation Investigation of J-Shaped and Kammtail Virtual Airfoils in Small-Scale Horizontal Axis Wind Turbines7
High-Order Large Eddy Simulations of a Wind Turbine in Ducted and Open-Rotor Configurations7
The Limit to Concentric Electrohydrodynamic Analysis of a Sedimenting Compound Drop7
Experimental Comparison of Hydrodynamic Behavior Under Partial Flowrates and Cavitation in Three Configurations of a Centrifugal Pump With Inducer and Impeller7
Backflow-Induced Negative Cross-Coupled Stiffness—A Numerical Study of Multistage Axial-Flow Impeller Rotordynamic Forces7
A Physical Interpretation of Swept Blades in Axial Compressors Employing Spanwise Equilibrium Analysis6
Study of a Cavitation Treatment in Kaplan Hydro-Turbine6
Inflow Conditions and the Flow Behavior of Submerged Annular Viscoplastic Non-Newtonian Jets6
Numerical Studies on the Oil Film Thickness in the Case of Stratified Flow With Different Oil–Water Flow Combinations Through Sudden Contraction Tube6
Behaviors of a Droplet Impact on a Cylinder6
An Optimization-Based Design Strategy for Centrifugal Compressors of Automotive Turbochargers and the Comparison of Five Particular Optimization Methods6
Flow State at Impeller Inlet: Optimization of Conical Frustum Section of Elbow Inlet Conduit in Large Low-Lift Pump Station6
Overturn Prevention Simulation of a Truck With Corner Nozzles6
Instability of Poiseuille Flow in a Bidisperse Porous Medium Subject to a Uniform Vertical Throughflow Effect6
Large Eddy Simulation of a Turbulent Polydisperse Spray Flow: A Comparative Study of Subgrid Scale Models and Droplet Injection Models6
Numerical and Experimental Flow Visualization of a Jet Flow around a Cylinder6
Detached Eddy Simulation of Micro-Vortex Generators Mounted on NACA 4412 Airfoil6
Relaxation Fluidic Oscillators: Design Parameters, New Operating Modes, and Characteristics of Their Internal and External Flows6
Role of Secondary Ions on the i-v Characteristics of Oxyfuel Flame Subject to an Electric Field6
Special Issue on the 2022 Fluids Engineering Division Summer Meeting6
An Actuator-Disk Model Augmentation for Low-Pressure Axial Fan Simulation6
A Combined Delayed Detached Eddy Simulation and Linearized Navier–Stokes Equation Study on the Generation and Reduction of Aerodynamic Noises Inside Steam Turbine Control Valve With Acoustic Liner6
Hydrodynamics of a Multisized Particle Mixture in Shallow Fluidized Bed With Immersed Tubes6
Flow Over a Square Cylinder at Intermediate Reynolds Numbers6
Structure Optimization and Cooling Performance of a Heat Sink With Discontinuous Triangular Ribs Impacted by Hybrid Nanofluid Confined Slot Jet Impingement5
Erosion Wear Analysis on Valve Cage of Cage-Typed Sleeve Control Valve for Coal Liquefaction5
The Effect of Curved Geometry on Exiting Flow of Fluidic Oscillators5
Analyzing Hydrogen Flow Behavior Based on Deep Learning Sensor Selection Optimization Framework5
On Boundary-Layer Stabilization by Bio-Inspired Compliant Coatings for Underwater Drones5
A Multiscale Euler–Lagrange Model for High-Frequency Cavitation Noise Prediction5
Boundary-Layer Agitator for Advanced Convective Mixing5
The Effect of Backward Curved Back Vanes and Back Channels on Fiber Entry Into the Back Shroud Cavity of a Wastewater Pump5
Experimental and Numerical Investigation of a Needle-Ring Type of Ionic Wind Generator Acting Alone and as a Flow Enhancement Device5
A Comparative Design Study of Biomimetic Multiwinglets for Tip Vortex Splitting5
Effect of Rotation on the Three-Dimensional Flow Around Two Side-by-Side Circular Cylinders at Reynolds Number 39005
Experimental Study of The Pressure-Time Method With Potential Application for Low-Head Hydropower5
Optimization of Exhaust Covers in Marine Scrubbers5
On Particulate Taylor-Couette Flow Driven by Periodically Oscillating Cylinders5
Numerical Investigation of Nature-Inspired Dune-Shaped Vortex Generators for Drag Reduction in a D-Shaped Cylinder Flow5
Grid Convergence Properties of Wall-Modeled Large Eddy Simulations in the Asymptotic Regime5
Experimental Study of the Cavitating Flow on an Independently Heated Venturi Nozzle5
Experimental Study of Turbulence Response in a Slowly Accelerating Turbulent Channel Flow5
Fleet Based Monitoring With Multi-Feature Hierarchical Clustering5
Accuracy Computational Simulation of the Savonius Wind Turbine Aerodynamic Performance: Effect of RANS Turbulence Models5
Enhancement of the Thermodynamic Suppression Effect of Cavitation in a Hydrofoil With a Slit5
Numerical Investigation of the Influence of Cavitation on the Runner Speed at Speed-No-Load and Runaway for a Francis Turbine of Low Specific Speed4
Numerical Investigation on Tip Clearance Leakage Control for a Radial Turbine With Tip Control Holes4
Large Eddy Simulation of Transitional Separated Flow Over a Low Reynolds Number Cambered Airfoil4
Computationally Efficient and Interface Accurate Dual-Grid Phase-Field Simulation of Turbulent Drop-Laden Flows4
Numerical Study of Horizontal Launch Free Motions of Powered Natural Supercavitating Vehicles4
Necessity of Ventilation Compressibility in Numerical Simulation for Predicting Ventilated Supercavity Geometry and Supercavitation Flow Characteristics4
Competition Between Evaporation Rate and Surface Tension Affecting Particle Deposition in a Sessile Droplet4
Flow-Induced Vibration Analysis of Rigid Horizontal Pipelines Under Two-Phase Flow and Leak Conditions4
Benchmarking the Performance of the Actuator-Disk Method for Low-Pressure Axial Flow Fan Simulation4
Modeling the Surface Pressure Spectrum on Rough Walls in Pressure Gradients4
Dynamic Transition of Unsteady Supersonic Flow From Mach to Regular Reflection Over a Moving Wedge4
Computational Fluid Dynamics Modeling and Predicting Environmental Conditions in a Poultry Incubator4
Heat Transfer in Double Pipe Heat Exchangers With Small Tube Spacing4
Energy Exascale Computational Fluid Dynamics Simulations With the Spectral Element Method4
Oil–Water Emulsion Behavior Under Variable Brine Salinity and p H Conditions4
Numerical and Experimental Flow Visualization of a Sphere in the Wind Tunnel4
Impact of Wall Temperature on Aerothermal Characteristics of an Array of Surface Microstructures4
Maximum Likelihood Identification of Backflow Vortex Instability in Rocket Engine Inducers4
Aerodynamic Enhancement of Airfoils for Wind Energy Applications Using Active Fluid Gurney Flaps4
High-Speed Visualization and Characterization of Bubbles in a Bubble Absorber With Swirl-Induced Flow of Refrigerant4
Effects of Reynolds Number on the Wake Characteristics of a Notchback Ahmed Body4
Investigation of Tyre Pattern Effect on the Aerodynamics of a Passenger Vehicle4
X-Ray Flow Visualization: Techniques and Applications4
Rotary Displacement Pump With a Sinusoidal Working Chamber and Oscillating Pistons4
Data-Driven Sparse Reconstruction of Three-Dimensional Steady and Unsteady Flow Fields in a Centrifugal Impeller4
Validation of a RANS Turbulence Model for a S833 Wind Turbine Airfoil With a Trailing Edge Flap Using Oil Visualization and Pressure Taps4
Numerical Study of Bifurcation Structures in Reflected Shock-Wave/Laminar-Boundary-Layer Interaction Within an End-Wall Tube4
Particulate Flow of a Viscous Fluid Driven by a Torsionally Oscillating Disk4
Predicting Leidenfrost Temperature and Effects of Impact Conditions on Droplet Size Distribution in Film-Boiling Regime4
A Study of Shock-Induced Transient Jets: The Impact of Exit Conditions on Mach Disk and Vortex Ring4
Shock Vector Control of a Double Divergent Nozzle for Futuristic Space Vehicles4
Evaluation of Thermoacoustic Instability for Chemically Reacting Flows Using Large-Eddy Simulations4
Numerical Investigation of Unsteady Flow Characteristics of Planar Plug Nozzle in Overexpanded Conditions4
CFD Study on Effects of Unilateral Axial Clearance on Inner Pressure Distribution and Performance of a CO2 Scroll Compressor3
Associate Editor's Recognition3
Experimental Investigation of the Effect of Rake on a Bluff Body Equipped With a Diffuser3
Maximum Likelihood Identification of Cavitation Instabilities in Axial Inducers3
An Air-Bearing Floating-Element Force Balance for Friction Drag Measurement3
Propulsive Effect of Wall Vibrations3
A Numerical Study of the Flow Field Driven by a Submerged, High-Speed, Gaseous Jet3
Cavitation Performance of a Pump With Independently Rotating Inducer and Impeller in Co-Rotation and Counter-Rotation Modes by Varying Rotor Speeds3
Experimental Investigation of the Performance of a Novel Adiabatic Swirl-Flow Separation Apparatus in Air–Water Two-Phase Flow3
Investigation of the Volute Effect on Performance of a Centrifugal-Pump Impeller With High-Fidelity Simulations3
Analysis of Rotordynamic Stiffness Forces in a Mixed-Flow Pump With a Shrouded Impeller3
Model Verification and Experimental Study of the Turbomachinery Wake Flow Field Reconstruction3
Enhanced Liquid Detection in Wet Gas Metering Via Microwave Sensing and Random Forest Regression3
Morphological Features of a Splashing Drop Extracted Using Explainable AI3
A Computational Study of In-Phase and Anti-Phase Interactions of Fish in a Phalanx School3
A Comprehensive Study on Improving the Electrohydrodynamic Performance of Electroconjugate Fluid Micropumps Using Hydrodynamic-Shaped Electrodes3
Erratum: “Symmetric and Asymmetric Disturbances in the Rayleigh Zone of an Air-Assisted Liquid Sheet: Theoretical and Experimental Analysis,” ASME J. Fluid Eng., 2020, 142(7), p. 071302, DOI: 10.1115/3
Reconstruction of Three-Dimensional Structures From Two-Dimensional Sectional Flow Fields of Cavitating Turbulent Flows Using Machine-Learning-Based Super-Resolution3
Research on Predicting Gas–Solid Erosion in Series Elbows Using Interpretable Machine Learning3
Unraveling Coherent Structures in Pump-Turbine Tandem Cascades Using Enhanced SPOD3
Gaseous Entrainment Dynamics in a Viscous Pool Due to Combined Influence of Asymmetric Rotational Field and Crossflow of Air3
Methodology for the Development of a Closed 2-Channel Impeller With Low Susceptibility to Clogging3
Characterization of Two-Phase Wakes in an Upward Adiabatic Liquid-Gas Flow Around a Cylinder3
Maneuvering Prediction of a Surface Combatant in Calm Water With a Computational Fluid Dynamics-Informed Mathematical Model3
An Investigation on the Steady and Unsteady Wake Flow Regimes and Aerodynamic Characteristics of the Trapezoidal Cylinders Using Immersed Boundary-Lattice Boltzmann Method3
Flow Performance Improvement of Fluidic Oscillator Through Variation in Number of Ribs on Coanda Surface3
Flow Characterization in A Piezo-Acoustic Inkjet Printhead: Vortex Formation and The Role of Nozzle Tapering3
Selection Criteria for Rotor Number and Rotational Direction in Arrays of Closely Spaced Darrieus Turbines3
Parametric Assessment of Size and Peak Pressure Variability for Cavitation Bubbles Induced by Low-Voltage Discharge3
Coherent Flow Structures Near Tongue Region in a Centrifugal Fan With Forward-Curved Blades3
Comparison of Vortex Structures and Turbulent Heat Transport for a Single Jet and Multiple Jets in Crossflow3
A Numerical Investigation of the Longitudinal Vortex Pair Structure in Underbody Diffuser Flows3
Numerical Investigation of Duct Augmented Vertical Axis Wind Turbine With Cambered Airfoils3
Mitigation of the Pressure Pulsations in an Axial Turbine at Speed-No-Load With Independent Guide Vanes Opening3
Two-Sided Feed Analysis in Gerotor Pumps to Enhance Filling Performance Through Computational Fluid Dynamics3
Experimental Study on Airflow Upwash and Control of Thrust Increase Induced by Ceiling Effect on Microrotor3
Ground Effect of a Two-Dimensional Flapping Wing Hovering in Inclined Stroke Plane3
A Unified Mechanistic Model to Classify Flow Patterns and Predict Pressure Drops in Oil–Water Pipeline Systems3
Reviewer's Recognition3
Numerical Simulation of Air-Core Surface Vortex at Critical Submergence for Dual Horizontal Intakes3
In Memoriam: Frank M. White (1933–2022)3
Efficient Impeller Optimization for Centrifugal Pumps Based on Kriging Surrogate Model With Multipoint Infill Strategy3
Radial Forces Reconstruction on a Space Inducer From Casing Pressure Measurements3
Numerical Simulation of Two-Dimensional Giesekus Flow Past a Rotating Cylinder3
Advancing Machine Learning-Enhanced Flow Modeling for Collision Phenomena in Total Cavopulmonary Connection3
Aerodynamics and Flowfield of Distributed Electric Propulsion Tiltwing During Transition With Deflected Trailing-Edge Flap3
The Similarity Law of Cavitation Number on Cavitation Instability in Liquid Rocket Inducer3
Uncertainty of Sand Particle Erosion Measurements in Two-Phase Fluid Flow Conditions: A Monte Carlo and Machine Learning Approach3
Growth-Rate Prediction for Low-Speed Variable-Density Spatially Developing Turbulent Planar Shear Layers: Status and Prospects3
Physics-Based Reduced-Order Model for Liquid Ring Pumps2
Review—Drag Coefficients of Non-Spherical and Irregularly Shaped Particles2
Numerical and Theoretical Investigation of the Gap Flow in Centrifugal Fans for Design and Off-Design Conditions2
Large-Eddy Simulations of a Turbulent Boundary Layer Separation Over a Bump With Strong Pressure Gradients and Free-Stream Turbulence2
A Meshless Discrete Boltzmann Solver With the Radial Basis Function Finite Difference Scheme for Fluid Flows With Dirichlet Boundary Conditions2
Research on the Unsteady Evolution Mechanism of Internal Pressure in Ultra-High-Speed Double-Car Elevators Under Differentiated Ventilation Modes2
The Integral Momentum Balance Applied to Metering Orifices to Obtain the Pressure Drop and the Flow Rate With High Accuracy2
Streamwise Extent and Ramp Rate Effects on Laminar Boundary Layer Response to Plasma Actuator Vortex Generators2
Optical Considerations for Designing Laser-Based Volumetric Particle Tracking Velocimetry2
Investigation on Heat Transfer Characteristics of Rectangular Channels With Internal Rough Surface Naturally Formed by Selective Laser Melting Three-Dimensional Printing2
Flow Physics of a Rotating Bernoulli Pad: A Numerical Study2
A Volume-Averaged Hyperbolic System of Governing Equations for Granular Turbulent Flow Modeling With Phase Change2
Pressure Loss Coefficients of Ductwork Fitting Combinations With and Without Vanes (Baffles)2
Numerical Simulation of Hit Noise Generation Due to Sloshing Phenomenon in a Rectangular Tank Under Periodic Excitation2
Bubble Size Distribution Dependence on Liquid Viscosity and Gas Flowrate Within a Bubble Column With a Porous Sparger2
Numerical and Experimental Study of Electrohydrodynamic Interactions in Two-Phase Flow Under Constant and Transient Electric Fields2
The Structure of Inclined Choked Gas Jet2
Effects of Blockage Ratio on the Spatiotemporal Dynamics of Turbulent Flow Separation Around a Square Cylinder at Moderate Reynolds Numbers2
Behavior of Gas Entrainment Inside Viscous Pool Due to Combined Influence of Symmetric Rotational Field and Freestream Flow of Air2
Effect of Trimmed Rear Shroud on Performance and Axial Thrust of Multi-Stage Centrifugal Pump With Emphasis on Visualizing Flow Losses2
Mixing in Low Reynolds Number Reacting Impinging Jets in Crossflow2
Turbulent Flow and Wall Forces in Staggered Square Cylinder Porous Media: An Large Eddy Simulation Analysis2
Plume Spreading Due to Floor Conditions of a Plunging Liquid Jet Using Stereographic Backlit Imaging2
Control of Flow and Acoustic Fields Around an Axial Fan Utilizing Plasma Actuators2
Experimental Study of Turbulent Wake Flow Around Trapezoidal Cylinders With Varying Streamwise Aspect Ratios2
Computational Fluid Dynamics Modeling of Gaseous Cavitation in Lubricating Vane Pumps: On Metering Grooves for Pressure Ripple Optimization2
Numerical Investigation and Experiment on Natural Circulation Resistance and Energy Characteristics in a Circulating Axial Pump2
Droplet Formation in Dynamic Stratified Liquid–Liquid Systems for Solution-Based Deposition Methods2
Effect of Bypass Duct on the Thrust Vectoring Performance of Dual Throat Nozzle in a Supersonic Aircraft2
Study of the Flow Characteristics of Pumped Media in the Confined Morphology of a Ferrofluid Pump With Annular Microscale Constraints2
A Study on the Drag Reduction Characteristics of Flexible Appendage Submersible During Dives2
A Numerical Study of Cyclist-Cyclist Aerodynamic Interaction towards Efficient Overtaking Strategy2
A Fundamental Viscous Flow Study to Understand a Separation Control Mechanism2
Improving Three-Dimensional Synthetic Jet Modeling in a Crossflow2
Investigation of the Impact of Wear-Ring Clearance on Hydraulic Performance and Axial Thrust in Multistage Low-Specific-Speed Centrifugal Pumps2
A Three-Dimensional Open-Source Solver for Incompressible Viscoelastic Two-Component Flows2
Siphon Break Phenomena Associated With Pipe Leakage Location2
Curvature-Sensitive Transition Model Application to Flow Around a Smooth Circular Cylinder2
Localized Blowing for Near-Wake Flow and Vortical Structure Control in Turbulent Boundary Layers Over Periodic Two-Dimensional Roughness2
Lift Computation Through Crossflow Measurement Behind a Rectangular Semiwing in Ground Effect2
Investigation of Flow Behavior of Turbulent Wall-Jet in the Viscous Shear Regime With Moving Wall Condition2
Numerical Investigation of Hydrodynamic Characteristics for Semiplaning Ships: A Comprehensive Study Using OpenFOAM2
LES/Lagrangian-Particle-Simulation of a Supersonic Reactive Turbulent Planar Jet2
Experimental Study on the Pressure Increment and Flow Pattern Evolution of a Blade-Type Multiphase Pump Under Different Operating Conditions2
0.14673495292664