OOIR: Observatory of International Research

Papers

(The TQCC of Strojniski Vestnik-Journal of Mechanical Engineering is 3. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-01-01 to 2026-01-01.)

Article	Citations
Research on a Real-time Reliability Evaluation Method Integrated with Online Fault Diagnosis: Subsea All-electric Christmas Tree System as a Case Study	16
A Modified Approach to the Rack Generation of Beveloid Gears	14
Switch Semi-Active Control of the Floating Raft Vibration Isolation System	13
Research on a Rapid Method for Obtaining the Matching Point of the Static Operating Pressure of a Supersonic Jet in a Wind Tunnel	12
Preparation and Thermal Characterization of Nanographene- Enhanced Fatty Acid-Based Solid-Liquid Organic Phase Change Material Composites for Thermal Energy Storage	11
An Optimal Design Method of Hydrostatic Turntable Based on FPSO Algorithm	11
The Impact of Micro-texture Distribution on the Frictional Performance of Straight Bevel Cylindrical Gears	9
Design Optimization of Mechanical Valves in Dishwashers Based on the Minimization of Pressure Losses	9
New Device Proposed For Industrial Measurement of Rolling Bearing Friction Torque	8
Comparison Study of Four Commercial SARS-CoV-2-Rapid Antigen Tests: Characterisation of the Individual Components	8
Design of 3D Printed Below-Knee Prosthetic - A Finite Element and Topology Optimization Study	8
Experimental Research on Transmission Characteristics of Elliptic Gear Transmission Systems	8
Estimation of Surface Temperature and Heat Flux over a Hollow Cylinder and Slab using an Inverse Heat Conduction Approach	8
Scalability Solutions in Blockchain-Supported Manufacturing: A Survey	8
Multi-Response Optimization of the Tribological Behaviour of PTFE-Based Composites via Taguchi Grey Relational Analysis	7
Active Disturbance Rejection Control Algorithm for the Driven Branch Chain of a Polishing Robot	7
Correlation between Air Pollution and the Spread and Development of COVID-19 Related Disease	7
Experimental Study and Numerical Analysis on Windage Power Loss Characteristics of Aviation Spiral Bevel Gear with Oil Injection Lubrication	7
A Numerical Simulation and an Experimental Study on the Steady-State Levitation Characteristics of a Magnetic Ball Driven by External Electromagnets in a Fluid Tube: Applications to Micromachines	6
The Illusion of a Green Transition in Slovenia by 2050	6
Effect of Tool Geometry in Stir Zone for Hook Formation of Dissimilar Aluminium Alloys: A Parametric Investigation on Metallurgical and Mechanical Characteristics	6
Incorporation of a Simplified Mechanical Joint Model into Numerical Analysis	6
Finite Element Analysis of Notch Depth and Angle in Notch Shear Cutting of Stainless-Steel Sheet	5
The Dynamics of Tapered-roller Bearings – A Bottom-up Validation Study	5
Service Performance Optimization and Experimental Study of a New W-W Type Non-circular Planetary Gear Train	5

Inventory Risk Decision-Making Techniques Using Customer Behaviour Analysis	5
Acceleration Harmonic Estimation and Suppression for Hydraulic Load Simulator Based on Artificial Bee Colony with Chaotic Search Strategy	5
Study on the Properties of Sinusoidal Micro-Textured Ball End Milling Cutter for Milling Titanium Alloy	5
Short-term Creep Behaviour of Different Polymers Used in Additive Manufacturing under Different Thermal and Loading Conditions	5
Analysis of the Dynamic Characteristics of a Gear-Rotor-Bearing System with External Excitation	4
Removal of Inclusions and Trace Elements from Al-Mg-Si Alloys Using Refining Fluxes	4
A Study Using the Hybrid Fuzzy AHP&TOPSIS Method in the Conversion of a LEED-Certified Education Building into a Nearly Zero-Energy Building in a Cold Climate	4
Numerical Investigation of Erosion Due to Particles in a Cavitating Flow in Pelton Turbine	4
Public Handling of Protective Masks from Use to Disposal and Recycling Options to New Products	4
Influence Analysis and Performance Optimization of a Pneumatic Actuator Exhaust Utilization System	4
Nitriding HS6-5-2 Steel in Inductively Coupled Plasma	4
Lifespan Evaluation for a Standard RV Reducer based on Fatigue Strength Theory	4
The Double-Sided Upsetting of the End Thickenings on Rod Blanks	4
Detection of Outer Wall Defects on Steel Pipe Using an Encircling Rotating Electromagnetic Field Eddy Current (RoFEC) Technique	4
The Use of Heuristic Optimization Techniques on RV Cycloid Reducer Design: A Comparative Study	4
Evaluation of Surface Functional Properties of Polymeric Sliding Materials for Lubricated Metal-Polymer Pairs Applications	4
The Dynamic Behaviour of Symmetrical Laminated Nano-composite Containing Equal Numbers of Glass and Carbon Fibre Layers	3
Experimental Testing System for Adsorption Space Heating	3
Impact Behaviour Modelling of Magnetorheological Elastomer Using a Non-Parametric Polynomial Model Optimized with Gravitational Search Algorithm	3
Development of a New Expert System for Diagnosing Marine Diesel Engines Based on Real-Time Diagnostic Parameters	3
Effect of the Curvature Angle in a Conduit with an Adiabatic Cylinder over a Backward Facing Step on the Magnetohydrodynamic Behaviour in the Presence of a Nanofluid	3
Analysis of Educational Building’s Ventilation Suitability to Prevent the Spread of Coronavirus (SARS-CoV-2)	3
Dynamic Performance of C80 Railway Wagon Under the Influence of Wheel Polygons and Typical Mode Shapes of the Car Body	3
Rigid-hyperelastic Coupling Dynamic Model and Dynamic Characteristics of Spring type of Traction Robot	3
Machining of Hard-to-cut AISI 4462 Duplex Stainless Steel with an Environmentally Friendly Approach with Vortex Tube	3
Through-thickness Work Hardening Variation in Thick High Strength Steel Plates: A Novel Inverse Characterization Method	3
Improvement of the Dimensional Accuracy of a Ti-6Al-4V Ripple Disc During Electric Hot Incremental Sheet Forming	3
Quantitative Sequential Modelling Approach to Estimate the Reliability of Computer Controlled Pneumatically Operated Pick-and-Place Robot	3
Transient Flow Characteristics of a Pressure Differential Valve with Different Valve Spool Damping Orifice Structures	3
Research on the Cutting Performance of Self-Lubricating Tools with Microtexture of the Front and Back Surfaces	3
Optimization of FSW Processing Factors on Hardness for Dissimilar AA6061-T6 and AZ31B O Alloys	3
Editorial: Special Issue of the Faculty of Mechanical Engineering, University of Maribor — 30 Years of Excellence in Engineering Research	3