Kovove Materialy-Metallic Materials

Papers
(The TQCC of Kovove Materialy-Metallic Materials is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)
ArticleCitations
Effects of ultrasonic peening on corrosion fatigue and corrosion behavior of welded AA5086-H32 aluminum alloy9
"Effect of plasma spraying parameters on microstructure and thickness and porosity of WC-CrC-Ni coatings deposited on titanium "7
The yttrium substitution impact on mechanical properties of biodegradable Mg66Zn30Ca4 alloy5
Influence of gas-shielded welding process on the microstructure and properties of joints of 1100 MPa high-strength steel4
Impact of RE/Ba change on RE2O3 phase and BaZrO3 nanorods at low temperature in REBCO superconducting film3
The effect of laser pre-oxidation of stainless steel on joining to polyamide by the LAMP method3
Investigation of the mechanical properties of Inconel 718 and AISI 316L welded materials using continuous drive friction welding3
"High-cycle fatigue and tensile strength of AZ91 Mg alloy with MAO-epoxy duplex coating "3
Influence of tool rotational speed on the microstructure and mechanical behavior of friction stir processed AA 7050 aluminum alloy3
Effect of graphene codeposition on tribological behavior of Ni-plated anodic hard coating3
High temperature deformation behaviour of as-cast Al0.4Co0.9Cr1.2Fe0.9Ni1.2(Si, Ti, C, B)0.375 complex concentrated alloy during tensile and compression tests3
Microstructure, mechanical properties of dissimilar friction stir welded AA6063/AA5052 alloys, and optimization of process parameters using Box Behnken-TOPSIS approach3
Influencing impact toughness transition temperatures of high carbon powder metallurgy steels by nickel adding2
Study on microstructure and properties of typical copper foils2
A new test for evaluating crack sensitivity of materials during welding2
Metallurgical characterization of natural aging effects on pre-deformed Al 7075/T651 alloy during retrogression and re-aging heat treatment2
Analysis of thermal deformation behavior and workability of 37CrS4 special steel2
"The resonance between the mixing energy and the elastic strain energy as the reason for the composition modulation effect appearance during the spinodal decomposition of GaInPAs solid solutions "1
Microstructure and properties of steady magnetic field-assisted laser welded joints of CP780-TRIP590 steels1
Modeling roughness surface Rp of 3D selective laser melting metal materials1
"Investigation of the effect of shot blasting on the surface properties of the HA coatings processed by the EPD method "1
Effect of  phase precipitation on grain growth and mechanical properties of Inconel 718 prepared by selective laser melting1
Effect of tantalum (Ta) addition and heat treatments on the properties of Ti-rich Ti36Ni49Zr15 alloy1
Microstructure and properties of graphene/AlCoCrNiMox high-entropy alloy composites1
Study of thermal properties of the aluminium EN AW 2024-T3 alloy1
Study of mechanical and microstructural properties of arc-produced aluminum 6061 alloy thin plate and block using additive manufacturing1
Study of electronic and optical properties of As-doped TiO2 using first principles1
Laser additive manufacturing of graphene/CoCrFeNiNbx coatings and their application in automatic measurement robot devices1
Effect of antimony addition on the microstructure modification and properties evolution of hypereutectic Al-Si-Zr alloy1
Tensile properties of as-cast and aged Pb-Sn-Ca alloys for positive grids of lead-acid batteries1
Microstructure and mechanical properties of fibre laser welded joints of CP780 and TRIP690 steel1
Effects of hot deformation on microstructure evolution, hardness, and intergranular corrosion of 7085 aluminum alloy sheets1
Influence of Cu and C particle reinforcement on the mechanical, thermal, electrical, and soldering behavior of Sn88Bi12 solder alloy1
A comparative study of Fm-3m TiO2, ZrO2, HfO2, and CeO2 via atomistic modelling1
High temperature friction and wear of spark plasma sintered Ti-Cu matrix friction composites with additions of machining metal wastes and reinforced with graphene nanoplatelets and ceramic particles1
Effect of cold rolling reduction rate on high-temperature plasticity of 3207 duplex stainless steel1
Effect of laser beam power ratio on microstructural evolution and mechanical properties in dual beam laser welding of duplex stainless steels1
Microstructural and mechanical behavior of unique aluminum matrix composites reinforced with pre-synthesized Al/Cu core-shell particulates1
0.089756011962891