OOIR: Observatory of International Research

Papers

(The TQCC of Journal of Adhesion is 6. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Development of productive curing processes for the manufacturing of adhesively bonded milling tools	46
Machine learning-based assessment of hygrothermal aging performance in CFRP-aluminum alloy adhesive bonded structures	34
Low-velocity impact analysis of metal-composite joints with grain-refined A356 and reinforced epoxy adhesive using six node pentahedron cohesive elements	33
Material-related and various dependences of adhesion force on piezo velocity revealed on an AFM at moderate humidity	22
Effect of graphene nanoplatelets on mode I fracture Toughness of epoxy adhesives under water aging conditions	20
Failure mechanisms in pre-tensioned bonded hybrid joints	19
Adhesive paperboard connections in architectural applications: modelling, characterization, and performance assessment	17
A discussion on the various aspects of the minimum pressing time for polyurethane adhesives	16
Experimental and numerical study of rate-dependent mode-I failure of a structural adhesive	16
Optimization of chitosan adhesive properties by means of genipin crosslinking	15
Nano-toughened swelling resin as a high-Performance sealing and adhering agent for cementing remediation	14
Effect of laser pretreatment on the adhesive strength, fracture toughness, and strain distribution of carbon fiber reinforced thermoplastics via mechanoluminescence visualization	14
Life prediction of adhesive steel joints under ageing stress – experimentally based model validation	14
Preparation of high strength silicone-based electrically conductive adhesives with excellent electrical conductivity at low content of Ag fillers	13
Parametric investigation of bonded composite joints under Mode II using a new methodology based on design of experiments	13
Hybrid joints: adhesive and pretensioned bolts in automotive applications	13
Pull-out behavior of glulam connections with glued-in rod loaded parallel to the grain	12
Viscoelastic behavior of pressure-sensitive adhesive based on block copolymer and kraft lignin	12
A novel 3D fibre-reinforcement architecture for high performance natural fibre reinforced composite adhesively bonded joints	12
Penicillium expansum adhesion to materials used in food industry	12
Comparison between cure kinetics by means of dynamic rheology and DSC of formaldehyde-based wood adhesives	11
Investigation of Residual Strength in CFRP Double-Adhesive Single Lap Bonded Joints after Low-velocity Impact	10
Analysis of adhesive degradation mechanisms and strength prediction based on principal component analysis	10
Harnessing bio-based adhesives for engineered wood: a density functional theory-guided systematic review of properties and binding mechanisms	10
Innovative multifunctional nanocomposite coated aluminum alloy for improved mechanical, flame retardant, and corrosion resistance in automobile industries	10

Durability of the effectiveness of atmospheric plasma treatment applied to thermoplastic Styrene-Butadiene-Styrene (SBS) rubber	9
Enhanced strength and toughness of repurposed glass fiber reinforced adhesive joints for sewage applications	9
Assessing the effect of a thickness gradient on the shear stress profile at the epoxy/silicone interface of thin coatings subjected to transverse shear loads with finite element analyses	9
Underwater adhesive bonding for offshore structure maintenance and repair	9
Micro-nano structuring of aluminum alloy via hybrid-acid anodization for Enhanced interfacial bonding in Al/PEEK hybrids	9
The effect of urea-formaldehyde adhesive modification with propylamine on the properties of manufactured plywood	9
Influence of the joining technique on the structural behaviour of hybrid timber-steel cross-sections	9
Symmetric expressions of surface tension components	9
Enhancing adhesion and microstructural properties of cementitious mortars through submerged arc welding (SAW) slag incorporation	8
Statistical aspects of diffusive adhesion between polymers with drastically different molecular mobility: Weibull’s and normal probability analysis	8
Correction	8
Experimental investigation of adhesive joint strength and stress-based criteria under tensile/compression–shear stress state using a developed fixture	8
Determination of Mode I cohesive law of structural adhesives using the direct method	8
Effect of laser generated microgrooves geometric parameters on the shear strength of CFRP-Aluminium alloy adhesive joints	8
Enhancement of adhesion performance and hydrolytic stability of particleboard bonded with gum rosin-modified maleic anhydride and polymeric isocyanate	8
Evaluation of surface pretreatment methods on thin austenitic stainless steel foils for adhesive bonding applications	8
Methodology for evaluating the mechanical performances of a bonded assembly through complementary mechanical tests	8
Viscoelastic-adhesive modeling of hybrid adhesively bonded double-lap joints: analytical and numerical studies	8
A comprehensive review on adhesion interactions between formaldehyde–based adhesives and wood biopolymers on surface	8
Effect of combination of microstructure and surface treatment on shear strength of precision bonded joints	8
Inhibition of adhesion of dairy-associated bacteria on stainless steel by plant extracts from the Fez-Meknes region (Morocco)	7
Peel behavior of polyurethane/Monel 400 interface under load in saline water	7
Compliance Methods For Bonded Joints: Part I - Investigation Of The Standardized Methods To Obtain The Strain Energy Release Rate For Mode I	7
Development of a discriminant model based on visible – near-infrared hyperspectral imaging data for evaluating the distribution of fracture modes on the surfaces of wooden block-shear specimens	7
Preparation of isocyanate microcapsules by complex coacervation and its application in plywood	7
Assessing bonding and debonding properties of Evotherm modified bitumen with natural aggregates using surface free energy approach	7
Effects of support patches on the mechanical characteristics of adhesively bonded aluminium alloy single lap joints	7
Effects of the incorporation of modified kraft lignin on the mechanical properties of epoxy adhesive: experimental and theoretical approaches	7
Numerical analysis of the effect of ice-metal interface stress singularity on bonding failure	7
Comparative analysis of nanomaterial-enhanced epoxy coatings for steel rebar protection	7
Damage tolerance analysis of double strap joints with composite adherends	7
High-performance lignin-phenol-formaldehyde resins synthesised with hardwood lignin from continuous batch cooking-CBC process	7
Mode I fatigue threshold energy assessment of a polyurethane adhesive: effects of temperature and Paris law relation	7
Electrical properties of adhesives designed for smart debonding by a pulsed discharge method	7
Analysis of the effects of free-length on bonded T-joints by an elastoplastic meshless analysis	7
On the crack propagation along brittle viscoelastic adhesive layer in DCB test	7
Experimental investigation on enhancing the adhesive bonding behaviour of titanium-di-oxide-based BK-9 adhesives under varying ambient temperature	7
Adhesion and growth of titanium nitride coating deposited on AISI 316L using cylindrical magnetron sputtering	6
Adherend effect on the mode I fracture energy analysis	6
Fracture Energy Determination of Wedge-opening Double Cantilever Beam Tests	6
Metal-metal and metal-composite joints with 3D printed aluminium substrates: effect of surface treatment on the mode I fracture toughness	6
Chemical modification of jabon veneers with citric acid–polyol systems: impacts on dimensional stability and bonding performance of plywood	6
Process simulation of laser shock-based disassembly of adhesively bonded composite/metallic structural parts: a numerical upscaling	6
Improved theoretical study of stress behavior of reinforced concrete beam strengthened by prestressed carbon fiber reinforced polymer plates	6
Direct observation of oil-surface adhesion via sum frequency generation spectroscopy	6
An enhanced surface treatment for effective bonding of 7075-T6 aluminium alloys	6
Hybrid joints: laboratory vs. field conditions	6
Improving the reversible adhesion performance of an epoxy vitrimer adhesive through surface treatment technology	6
Multiaxial stress effects on bonding strength in adhesively bonded joints	6
Experimental and numerical investigation of the squeegee process during stencil printing of thick adhesive sealings	6

Gecko-inspired adhesives: mechanical principles, synthetic fabrications, and applications	6
Analytical axisymmetric Newtonian squeeze-flow models for adhesive bondline thinning: velocity- and force-controlled compression with Navier slip conditions	6
The effect of sulfur to accelerator ratio on the adhesion strength of NR/SBR blend to bronze-plated bead wire in sulfur curing systems	6
Pull-off strength of mushroom-shaped fibrils adhered to rigid substrates	6
Impact of recycled polyol content on the structure and performance of reactive polyurethane hot-melt adhesive	6
Effect of laser pre-treatment on adhesive joint performance and evaluation of interfacial strain distribution using mechanoluminescence	6
Dominant role of liquid film flow in contact time dependence of adhesion force at silica-graphite interfaces revealed on AFM	6