International Journal of Electronics

Papers
(The median citation count of International Journal of Electronics is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)
ArticleCitations
A new Buck-Boost converter with capability of eliminating right-half-plane zeros45
Trapezium backed dual circularly polarised hepta-band monopole antenna32
An improved isolated DC–DC Buck converter with high step-down ratio22
Design of carbon allotrope FET-based folded cascode operational transconductance amplifiers (FC-OTA)21
Fault classification in Digital to Analog Converter using machine learning18
A low-power, low-offset, and power-scalable comparator suitable for low-frequency applications15
DC/RF performance and temperature sensitivity of ground-plane based JLTFET15
A 200 MHz 1.22 fJ/bit/search single-ended content addressable memory cell design in 45-nm CMOS technology15
Circuit fault detection model using multiclass support vector machine14
Dual-ground transformerless nine-level dynamic voltage boosting inverter topology14
Design and implementation of low power multiplierless FIR filters on FPGA and ASIC13
Floating-capacitor based inverter for open-ended winding induction motor drive with fault-tolerance13
Miniaturized tri-band fractal antenna design for LTE, WLAN, WiMAX and C-band applications12
A low-profile high gain U slotted wide band micro-strip antenna for 5G applications12
Hybrid high step-up DC-DC converter based on quadratic and switched capacitor cells with reduced voltage stress across the switches12
SiC MOSFET gate oxide degradation monitoring: a gate leakage current approach11
Linear phased meta-material incorporated patch antenna array at sub-6 GHz for 5G base stations11
Application of Lévy flight particle swarm optimisation in MPPT of photovoltaic system11
A performance assessment of nine-stage ternary DC source mli through various PWM topologies10
On the ergodic capacity of MIMO-NOMA systems with JTRAS protocol under imperfect SIC and CSI9
A novel interleaved BIFRED-Zeta with intelligent MPPT for PV applications9
Efficient approximate multipliers with adjustable accuracy9
Design of double-integral sliding-mode controller for fourth-order double input DC - DC boost converter with a voltage multiplier cell9
Design and analysis of SRAM cell using swing restoration inverter for low power applications9
Speed sensorless control of a bearingless induction motor based on sliding mode observer with improved double power reaching law9
Parasitically loaded hexagonal-SRR mutually coupled wideband antenna for 5 G sub-6 GHz NR mid-bands9
High-gain transformerless voltage-lift switched-inductor converter8
A highly efficient adaptive body bias CMOS rectifier with double-side feedback at a tone of 2.4 GHz8
A circularly polarised monopole antenna with switchable frequency, pattern and polarisation8
Enhancing the design of a two-stage CMOS operational amplifier utilising the Bat Algorithm8
Design and implementation of seven-level inverter for grid-tied photovoltaic systems8
Fractional order PID controller optimised by hybrid algorithm for instant torque control of IM motor8
An Area Efficient Approach to Realize Vedic Multiplier using 4–2 Compressor adder for Image processing Applications7
Design of a compact MOSFET model suitable for geometric programming7
Design and investigation of pocket shaped fractal antenna using circular ring elements for UWB technology with stub loaded DGS7
UDE-based robust nonlinear control of the buck-boost power converter7
Detailed analysis and modeling of an improved cascade buck converter7
Low-power ternary inverter using vertical tunnel field-effect transistor with pocket7
A low-SAR four-element antenna for ISM/NR78 band applications7
A 0.75V 10nm FinField-Effect Transistor Based Hybrid Self Controlled PreCharge Free Content Addressable Memory for Low Standby Power Applications7
Dual feedback radiation-tolerant SRAM for space application7
Design and analysis of sub-threshold level shifter for very high speed and ultra-low power applications7
Design and analysis of a dual input quasi SB-SC cell high gain converter7
Performance evaluation of a 15-level inverter using two DC sources with lower standing voltage6
Performance investigation of junctionless nanosheet FET with dual-k sidewall spacer using numerical simulations6
High-isolation coradiator-based UWB MIMO antenna for on-body IoT applications6
Grounded and floating memristor emulator employing ICCTA: decremental or incremental operation6
Development of an ultrawide bandwidth and high gain millimeter wave antenna for 5G wireless networks6
Slotted meandered waveguide antenna for X-band radar applications6
Enhancing torque control in brushless dc motors with hybrid fractional order PID controller approach6
An improved gate-pulse rotation method for efficient voltage balancing in modular multilevel converters for railway applications6
High isolation multiport integrated antenna system for cognitive radio applications6
Design of 30 nm multi-finger gate GaN HEMT for high frequency device6
Compact metamaterial-inspired high isolation triple-band dual-polarised MIMO antenna for 3G-6G applications6
Development of adaptive cooperative jamming technique for pulse compression radar using hybrid meta-heuristic algorithm6
Design of a novel four-element Koch–Sierpinski fractal mmWave antenna for 5G applications6
Modelling and analysis of single-inductor dual-input and dual-output DC–DC converter for e-mobility5
Wireless power transfer with LCC-compensated transmitter and center-tapped receiver winding5
Optimised GRS coded cooperation: sliding relay selection design and improved joint decoding5
High-performance approximate Booth multiplier based on novel encoding scheme and 4–2 compressor5
Modulation signal identification and classification based on the OA algorithm model5
A compact quad-port slotted-spatula shaped ultra wide-band MIMO antenna for mm-Wave, 5G and beyond communications5
High gain step up converter with fault detection and fault-tolerant ability5
MBOA based PV array interconnection scheme for enlarging the harvested power under PS condition5
Super-twisting hysteresis controller for multi-rotor wind energy systems5
A 5-level T-type inverter fed six-phase induction motor drive for industrial applications5
Low RCS MIMO antenna with high isolation based on polarisation conversion surface5
Optimum Chebyshev filter with an equalised group delay response5
Design of Synchronous RF-DC Rectifier for Energy Harvesting System5
Synthesis of stacked HSC-T using improved mixed frequency PWM5
An optimised resource allocation scheme based on NOMA-SWIPT in cooperative network5
A 92.95%-efficiency high-voltage dual-mode buck converter using 0.5-µm HV CMOS process5
A Rotatable Frequency- and Pattern-Reconfigurable Antenna with a Wide Tunable Bandwidth5
Self-multiplexing textile antenna aided by SIW cavity for wearable applications5
Compact design of universal gates with non-aligned gate technology and assessment of its performance in a TCAD Environment5
Analysis and implementation of a single switch-based non-isolated high-gain DC−DC converter for renewable applications4
Multi-objective optimisation design of stator slot parameters for bearingless induction motors4
Implementing comb-based FIR filters on actual FPGA boards4
Differential RVCO with low power, low phase noise and wider tuning range for PLL application4
Ultrawideband low-RCS metasurface optimised by an improved PSO algorithm4
A non-isolated MIC for PV application with wide input voltage range4
Design of a compact quad-port wideband printed MIMO antenna for vehicular communication environment4
Novel design of power-efficient quaternary logic gates using CNTFET4
Simultaneous compensation of distorted DC bus and AC side voltage using enhanced virtual synchronous generator in Islanded DC microgrid4
On-chip supply noise in multiprocessors: impact and clock gating inspired mitigation strategies4
Energy-Efficient approximate compressor design for error-resilient digital signal processing4
Variation aware resilient flip-flop design for low-voltage applications4
Dual-element MIMO wideband 5G radiator using metamaterials at 28GHz4
A comprehensive LPF-droop control based on virtual impedance and matching power command switching in DFIG4
Design of an adaptive finite impulse response filter using low error efficient approximate adder and two-stage operand trimming approximate logarithmic multiplier for WSN in IoT4
Dual input high gain step-up converter for DC grid applications: design, dynamic control and performance analysis4
Pattern diversity enabled bandwidth reconfigurable MIMO antenna4
Design and analysis of quasi-resonant high-gain impedance source DC–DC converter for DC microgrid4
Enhanced performance of full adder using advanced 9-T XOR-XNOR module4
Interleaved high gain modified SEPIC converter in DC microgrid systems4
ANN-based design analysis of O-shaped slotted microstrip patch antenna for L band applications4
Gain enhancement of antenna using tuned complementary FSS for wireless communication4
Improved performance of highly compact CP implantable antenna using slots4
Optimisation of asymmetries in mm-wave single-element fractal antenna for gain-bandwidth enhancement4
Hybrid small-signal model parameter extraction for GaN HEMT based on QGA4
A bulk-driven quasi-floating gate regulated cascode current mirror and its application4
Design and analysis of two-stage PVT-tolerant reset-free phase frequency detector for PLL frequency synthesiser in 45nm CMOS technology4
Sensorless control of an axial flux motor using square-wave injection for low switching frequencies4
A reduced device symmetrical-asymmetrical multilevel inverter with self capacitor voltage balancing and reduced capacitor voltage ripple3
28/38 GHz compact rhombic-shaped antenna for future generations of mobile communications3
Light load analysis and topology morphing between full-/half-bridge DC-to-DC converter3
Dual-band frequency selective surface with sharp band edges3
Direction of arrival estimation via DE based-optimised excitation amplitude and spacing3
Analysis of bridge type and bridgeless cuk converter fed motor drives for improved power quality3
Design and optimization of broadband CPW rectenna for RF energy harvesting3
Design and implementation of novel multilevel inverter with full DC-utilization3
Design and implementation of single-phase modified bridgeless positive output CSC converter3
Low-power ternary full adder/subtractor design using GNRFET technology3
Behavioural modelling of Low-Noise amplifier using the NRBO-TCN-BiGRU algorithm3
A line loss detection method for three-phase unbalanced loads in low-voltage distribution stations based on IoT sensing and swarm intelligence3
Design and optimisation of an R-shaped microstrip patch antenna using CSO and curve fitting for mmWave 5G applications3
Voltage-controlled oscillators using CFOAs with correction terminal Z3
Adaptive clustering with continuous phase modulation in NOMA systems3
DSTATCOM using model predictive control associated with LMS control3
Wide voltage range and low current ripple bidirectional DC/DC converter3
A novel square‐shaped four‐port multiband MIMO antenna with enhanced characteristics for sub 1 GHz and sub 6 GHz 5G applications3
Electromagnetic band gap metamaterials printed hybrid reconfigurable patch antenna for 5 G and beyond applications3
Dual randomized discontinuous pulse width modulation for three-phase inverter3
Frequency control enhancement of an islanded microgrid using disturbance-observer-based approach3
Impact of source/drain lateral straggle on GIDL current of low SS NC-FinFET3
CMOS Synthesis of Multiple-Valued Multiple Threshold Functions– analysis and comparison3
Improved linear/nonlinear active disturbance rejection switching control for bearingless induction motor3
Simulation-based analysis of an L-patterned negative-capacitance dual tunnel VTFET3
AI-enhanced single-phase bridgeless buck-boost AC-DC converter for high-efficiency LED driver applications3
Composite chattering-free discrete-time sliding mode controller design for PMSM3
A new dual input boost converter with coupled inductors3
Efficient quantum-dot adder optimisation and analysis for future circuits3
A tunable graphene-VO 2 metasurface for multiband absorption-reflection switching in 6 G communication3
A novel quaternary inward inverter gate based on MIN and MAX functions3
Novel double stator switched reluctance generation system with energy storage units3
A hybrid binary logical regression -gradient decent approach for dynamic cooperative spectrum sensing in CRN3
Wideband GaN HEMT Doherty power amplifier for 5G and satellite applications3
A low complexity and high modularity design for continuously variable bandwidth digital filters3
Data transmission via hybrid fuzzy time slot scheduling in long-range communication2
Optimized CNN and adaptive RBFNN for channel estimation and hybrid precoding approaches for multi user millimeter wave massive MIMO2
Statement of Removal: Knowledge-based heuristic optimisation technique for mm-wave 5G antenna2
A novel cascaded multilevel boost converter fed multilevel inverter with reduced switch count2
Wireless power transfer empowered by reconfigurable intelligent surfaces2
A new high step-down soft-switched DC–DC converter based on coupled inductor2
A 16-bit time-interleaved low-pass delta-sigma modulator and duty-cycle-error compensation2
A New Generalised Symmetrical/Asymmetrical Boost Integrated Multilevel Inverter with Reduced Components for PV/UPS Applications2
An improved Z-source-derived converter for efficient PV integration2
A novel intelligent hybrid algorithm for maximum power point tracking in PV system2
DGS and metamaterial incorporated highly isolated wideband MIMO antenna2
Closed form expression to predict the resonant frequencies of a dual band asymmetric double-sided printed dipole antenna2
On the optimisation of detector threshold for energy efficient CSS over fading channels2
Statement of Removal: Design and analysis of 1-bit hybrid full adder cells for fast computation2
A compact microstrip quint-band bandpass filter using shorted stub-loaded SIRs based on the interdigital feedline structure2
Design of energy efficient N-bit vedic multiplier for low power hardware architecture2
Hybrid approach for 3 phase bridgeless AC to DC Cuk converter for WECS2
4-port MIMO antenna backed with frequency selective surface (FSS) for improved characteristics in n46 and n47 WLAN Bands2
Error analysis of quadruple-correlated cooperative communication systems2
Performance analysis of high voltage extended boost (HVX-B) converter with optimised MPPT control for PV-Grid application2
Optimization of LDPC decoding algorithm in semi-conductor storage based on artificial neural networks2
High isolation pattern diversity multiband MIMO antenna using ring and stub with bandstop filter2
A high current efficiency rail-to-rail operational amplifier2
Design and performance analysis of an optimised hybrid boost converter with coupled inductor for PV-based EV applications2
Design and implementation of a high step-up DC-DC converter with low voltage stress on devices and enhanced gain-to-element ratio2
An accurate interpolation-based iterative frequency estimator of 2D multi-frequency sinusoids2
Fixed-frequency modified gating signals controlled high-frequency isolated LCL-T DC-DC resonant power converter2
Improved ultra voltage gain switched inductor based-Y-Source DC/DC converter with low device stress2
Multi-target CFAR detector based on compressed sensing radar system2
An interleaved multilevel converter for onboard EV charging application2
Effects of metal work function and gate-oxide dielectric on super high frequency performance of a non-align junction DG-MOSFET based inverter in the sub -100 nm regime: 2
Single carrier PWM-based power balancing for five-level CHB inverter2
An adaptive routing selection algorithm based on improved ant colony optimisation for mobile ad hoc networks2
Novel Low Profile Beam Switchable 5G Sub-6 GHz E-GSM Antenna for Vehicular Communication2
A monostatic RCS reduction study for an antenna in structural mode at X band2
A step-up multilevel inverter with reduced devices and input current ripple2
Analysis of STC-GFDM with Walsh Hadamard in generalized η−μ fading channel2
A corrugated edge tapered slot dual polarized MIMO antenna for phased array systems2
Low power design of energy efficient median filter2
An improved PWM with simplified unified switched logic (USL) for RSC MLIs2
Design and analysis of GQ-Based SC coupled-inductor inverter for DC-AC boost conversion2
FPGA implementation of proficient Vedic multiplier architecture using hybrid carry select adder2
A novel merged carrier PWM for improved line-harmonic performance of three-phase reduced switch count MLI configurations2
An improved maximum boost control technique for CDBC-based three-level ZSI2
A novel boost self-balanced thirteen-level inverter based on switched-capacitor H-bridge units2
High-efficiency class-F power amplifier based on double spiral defected ground structure2
A high boost switched capacitor multilevel inverter with reduced components2
A progressive phase multiple-injection locking technique for jitter suppression in voltage-controlled ring oscillator2
Thermal analysis of analog and noise parameters of dual material recessed source-drain junctionless gate all around MOSFETs2
EMSOA based application mapping framework for power optimisation in 3D-NoC2
Hybrid matrix converter for grid connected multiphase wind generation2
Analysis and design of switched capacitor-based Quasi-Z-Source DC-DC converter with improved operation factors2
Design and analysis of low-profile quad element wide band MIMO antenna with efficient isolation for C and X-band applications2
FPGA based design and performance evaluation of 32-bit hybrid carry select adder architectures2
An X-band conformal FSS with enhanced shielding effectiveness2
Design and FPGA implementation of digital down converter using reversible adders2
Ultra-wide stopband miniaturised Wilkinson power divider for application in Doherty power amplifiers2
Design and performance of self adaptive SRF-PLL technique for grid synchronisation2
Research on MPPT control strategy based on CCAOA algorithm2
Miller capacitance reduction in negative capacitance TFETs2
A low-voltage and low power FinFET based full-wave rectifier2
Circulating current control of MMC-fed induction motor drive under entire speed range operation2
A reconfigurable single and multi-switch fault-tolerant multilevel inverter1
A novel non-isolated step-up/step-down DC-DC converter with wide voltage gain1
A modified perturb and observe MPPT algorithm with zero steady state oscillation for single-phase grid-connected transformerless solar inverter1
Theoretical and experimental study of an annular ring patch antenna on two layers1
A novel non-isolated step-down converter with low switch voltage stress1
Bandwidth oriented approach for the design of a PI controller for a three phase two-stage grid-connected PV system1
Sensorless speed control of BLDC motor drive using Volt/Hertz method1
A scalable and adaptive cell-level mapping algorithm for QCA placement and routing1
Low leakage, differential read scheme CNTFET based 9T SRAM cells for Low Power applications1
A low-power SRAM design with enhanced stability and I ON /I OFF ratio in FinFET technology for wearable device applications1
Conducted interference and voltage ripple suppression study in LLC resonant converter based on symmetric chaotic spread spectrum1
DER integrated BTB-VSI based DSTATCOM for PQ enhancement1
A high-gain step-up DC-DC converter based on a three-winding coupled-inductor and voltage multiplier cell with enhanced voltage stress on devices1
High gain solar-powered electric vehicle drive system using improved quasi-coupled inductor boost converter and advanced PI control1
Impact of process parameters variation on noise and linearity performances of GC-JL-GAA MOSFET1
Enhancing robust control of DC-DC converters: adaptive super twisting control based on barrier function1
High gain multi-stage DC-DC boost converter using improved switched-inductor network with reduced voltage stress1
A Reduced Switch Count Multilevel Inverter for PV Standalone System using Modified JAYA Algorithm1
Multi band multi polarised fractal antenna for white space TV band1
A 24.1 TOPS/W mixed-signal BNN processor in 28-nm CMOS1
Simultaneous power, delay, and crosstalk noise reduction for the BUS encoding method of ternary LWC plus quaternary TS1
A 28 GHz transformer-based Doherty power amplifier for FR2 5G applications in 40 nm CMOS1
A novel structure for multi-level inverter with reduced components1
A compact SIW dual-functional design with integrated filter and self-diplexing antenna1
Mobile-integrated SRR-based four-port MIMO antenna for broadband mm-wave 5G applications1
An energy-efficient design of ternary SRAM using GNRFETs1
DC impedance modelling and stability analysis of droop mode parallel DC power supply system1
A Novel Hardware Efficient High Resolution Spectrum Hole Detection Technique for Cognitive Radio1
Evaluation of dual-ONOFIC method for subthreshold leakage reduction in domino circuit1
Design of miniaturised circular polarisation-reconfigurable and frequency agile slow-wave SIW based microstrip antenna for wireless applications1
High-performance Schmitt trigger buffer with DTMOS integration1
A high step-up soft-single switched converter with three coupling inductors1
Modelling of single band and double band hysteresis based current controlled voltage source inverter in a microgrid1
A novel switched-capacitor based multilevel voltage boost inverter for EV interface1
Hybrid closed-loop controller for modular multilevel converter with optima number of sensor approach1
Super-wideband fractal antenna of two-arm structure with broadband balun1
A reconfigurable routing architecture of asynchronous NoC systems1
0.28-nW level-shifter folded flipped source follower fourth-order low-pass-filter IC design1
An Optimized Sequence for Sparse Channel Estimation in a 5G MIMO System1
Gain and bandwidth enhancement using superstrate loaded 2×2 circular-array antenna for X-Band and RADAR applications1
Dual-hop communications over PLC/ η-μ and PLC/ λ-μ fading channels1
A new low voltage low power fully differential CMOS class AB current output stage with unique current drive capability1
A dependable and resource-frugal ring oscillator physically unclonable function1
Design of digital compensators for multi-output DC-DC converters with reduced cross-regulation1
Design and implementation of switched capacitor-based high gain converter1
A 2.71 fJ/conversion-step 10-bit 50 MSPS split-capacitor array SAR ADC for FOG systems1
Fuzzy Based Hybrid Controller for UPQC with Wind and Battery Storage Systems1
A fast-locking low-reference spur cascaded PLL with gate-diffusion input-based phase detector and pulse width amplifier1
A multi-beam circularly polarised Fabry-Perot resonator antenna array using SIW for X-Band applications1
Power balancing and performance enhancement of a five-level CHB inverter using a simplified PWM technique1
0.22169208526611